Zhone-VOICE-ANALOG-IF-MIB Table View

The Analog Voice Standard Configuration Table. It contains 
the standard configuration information of the analog          
telephony interface.

zhoneVaIfCfgEntry row .1.3.6.1.4.1.5504.5.6.1.1.1

An entry in the configuration table for each voice analog
interface. The entry is created when the voice analog
hardware is detected.

Indexes

IF-MIBifIndex

Column	Syntax	OID
zhoneVaIfCfgImpedance Specifies the terminating impedance of voice analog interfaces. other - none of the following; arbitrary, within limits, for special cases. ohms600Real - 600 Ohms. ohms600Complex - 600 Ohms …	Enumerationr/w Enumerated Values: 1 other 2 ohms600Real 3 ohms600Complex 4 ohms900Complex 5 ohmsComplex1 6 ohmsComplex2	.1.3.6.1.4.1.5504.5.6.1.1.1.1
zhoneVaIfCfgReceiveTLP Receive Transmission Level Point (RTLP) settings control the amount gain or loss added to the incoming signal after it is decoded to analog. to increase the signal level set the RTLP setting to higher values. The defa…	Enumerationr/w Enumerated Values: 1 fxsRtlpN9db 2 fxsRtlpN8db 3 fxsRtlpN7db 4 fxsRtlpN6db 5 fxsRtlpN5db 6 fxsRtlpN4db 7 fxsRtlpN3db 8 fxsRtlpN2db 9 fxsRtlpN1db 10 fxsRtlp0db 11 fxsRtlp1db 12 fxsRtlp2db 13 fxsRtlp3db 14 rTlpNummeric	.1.3.6.1.4.1.5504.5.6.1.1.1.2
zhoneVaIfCfgTransmitTLP In case of FXO, it specifies FXO attenuation and default value is 0dB(fxsTtlp0db). In case of FXS this setting controls the amount of gain or loss added to a voice signal from CPE before it is encoded to digital PCM…	Enumerationr/w Enumerated Values: 1 fxsTtlp9db 2 fxsTtlp8db 3 fxsTtlp7db 4 fxsTtlp6db 5 fxsTtlp5db 6 fxsTtlp4db 7 fxsTtlp3db 8 fxsTtlp2db 9 fxsTtlp1db 10 fxsTtlp0db 11 fxsTtlpN1db 12 fxsTtlpN2db 13 fxsTtlpN3db 14 tTlpNummeric	.1.3.6.1.4.1.5504.5.6.1.1.1.3
zhoneVaIfCfgTrunkConditioning The trunk conditioning setting specifies whether the FXS/FXO port should send the idle pattern to the network upon declaration of a Carrier Group Alarm(CGA) on the WAN link to which the port is assigned . In most cases …	Enumerationr/w Enumerated Values: 1 off 2 idle 3 busy	.1.3.6.1.4.1.5504.5.6.1.1.1.4
zhoneVaIfCfgLineType The Card type FXS, FXO, EM, EBS. Entries in the table will be created or deleted on the basis of zhoneVaIfCfgLineType in the zhoneVaIfCfgTable and we are not using rowStatus entry for this . The tables which are augum…	Enumeration Enumerated Values: 1 fxs 2 fxo 3 em 4 ebs	.1.3.6.1.4.1.5504.5.6.1.1.1.5
zhoneVaIfCfgIntegratedDSP Indicates whether the interface has an integrated Digital Signal processing (DSP) unit.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.5.6.1.1.1.6
zhoneVaIfCfgLineCapabilities The Interface types supported on this interface. This is a bit-map of possible types. This variable can be used to determine zhoneVaIfCfgLineType.	Bits Enumerated Values: 0 fxs 1 fxo 2 em	.1.3.6.1.4.1.5504.5.6.1.1.1.7
zhoneVaIfCfgMaintenanceMode Indicates the maintenance modes of the Analog voice interface. loopback options for Fxo and Fxs cards (Zhone specific) ---------------------------------------…	Enumerationr/w Enumerated Values: 1 off 2 ifDigitalLoopback 3 ifAnalogLoopback	.1.3.6.1.4.1.5504.5.6.1.1.1.8
zhoneVaIfCfgPCMEncoding alaw(1) :for E1 mulaw(2) : for T1	Enumerationr/w Enumerated Values: 1 alaw 2 mulaw	.1.3.6.1.4.1.5504.5.6.1.1.1.9
zhoneVaIfCfgReceiveTLPNum Receive Transmission Level Point (RTLP) settings control the amount gain or loss added to the incoming signal after it is decoded to analog. to incrase the signal level set the RTLP setting to higher values. The defaul…	dB/10Integer32r/w Constraints: range: -160-85	.1.3.6.1.4.1.5504.5.6.1.1.1.10
zhoneVaIfCfgTransmitTLPNum Transmit Transmission Level Point controls the amount of gain or loss added to a voice signal from CPE before it is encoded to digital PCM. To increase the signal level, reduce the TTLP setting to lower value. The def…	dB/10Integer32r/w Constraints: range: -175-70	.1.3.6.1.4.1.5504.5.6.1.1.1.11
zhoneVaIfCfgLoopCurrent To set the loop current value for a subscriber	mAInteger32r/w Constraints: range: 20-44	.1.3.6.1.4.1.5504.5.6.1.1.1.12
zhoneVaIfCfgRingVoltage To set the ring voltage for a subscriber.	Enumerationr/w Enumerated Values: 1 b85vrms 2 b75vrms 3 b92vrms	.1.3.6.1.4.1.5504.5.6.1.1.1.13

The Analog Voice Status Table.  It contains general 
information about the status of Analog Telephony interface
including the error statistics.

zhoneVaIfStatusEntry row .1.3.6.1.4.1.5504.5.6.1.2.1

An entry in the status table for each Analog voice interface.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneVaIfStatusSignalErrors Accumulated number of signaling protocol errors that are detected in the interface since system startup.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5504.5.6.1.2.1.1
zhoneVaIfStatusInfoType The information transfer services for the current call. none - no information transfer service, this is set befgore the first call is made on the interface. voice - analog voice. g3Fax - Group 3 FAX.	Enumeration Enumerated Values: 1 notype 2 voice 3 g3Fax	.1.3.6.1.4.1.5504.5.6.1.2.1.2

The FXS standard configuration table. It contains
FXS configuration parameters, one entry per FXS interface.
The configuration information of this table is set by 
hardware with its default setting or CLI during the hardware 
installation time.

zhoneVaIfFXSCfgEntry row .1.3.6.1.4.1.5504.5.6.2.1.1

An entry in the standard configuration table for
each FXS interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
zhoneVaIfFXSCfgSignalType the signaling type of FXS interface. fxsLoopStart - loop start. fxsGroundStart - ground start. fxsLoopStartFd fxsGroundStartAutomatic - Used with equipment requiring fast response time to the Central Office. fxsGround…	Enumerationr/w Enumerated Values: 1 fxsLoopStart 2 fxsGroundStart 3 fxsLoopStartFd 4 fxsGroundStartAutomatic 5 fxsGroundStartImmediate 6 fxsdnLoopStart 7 fxsdnLoopStartFd 8 fxsdnGroundStart 9 fxsdnGroundStartImmediate 10 fxsdnwinkLoopStart 11 fxsdnwinkLoopStartFd 12 fxsdnwinkGroundStart 13 fxsdnwinkGroundStartImmediate 14 fxstr08SingleParty 15 fxstr08UniversalVoiceGrade 16 fxstr08UniversalVoiceGradeAutomatic	.1.3.6.1.4.1.5504.5.6.2.1.1.1
zhoneVaIfFXSRingFrequency the ring frequency to be used in the FXS interface. ringFrequency25 - ring frequency 25 Hertz. ringFrequency50 - ring frequency 50 Hertz. ringFrequency20 - ring frequency 20 Hertz.(Default) ringFrequency30 - ring f…	Enumerationr/w Enumerated Values: 1 ringFrequency25 2 ringFrequency50 3 ringFrequency20 4 ringFrequency30	.1.3.6.1.4.1.5504.5.6.2.1.1.2
zhoneVaIfFXSRingBack the ring back is requested if this variable is set to on.	Enumerationr/w Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.5504.5.6.2.1.1.3

The Foreign Exchange Station (FXS) interface Status Table.
It contains hook status, ring active and other states of
the interface.

zhoneVaIfFXSStatusEntry row .1.3.6.1.4.1.5504.5.6.2.2.1

An entry in the status table for each FXS interface.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneVaIfFXSHookStatus This object contains the hook status of FXS interface. onHook - the connected equipment(e.g., phone) is onHook. offHook - the connected equipment is offHook.	Enumeration Enumerated Values: 1 onHook 2 offHook	.1.3.6.1.4.1.5504.5.6.2.2.1.1
zhoneVaIfFXSRingActive This object contains the outgoing ring active indication. If the object value is true, then the interface is currently generating ring out to the Key Telephone System (KTS) or Plain Old Telephone (POT); otherwise, it d…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.5.6.2.2.1.2
zhoneVaIfFXSRingGround This object contains the incoming ring ground indication. It is only valid when the zvaIfFXSCfgSignalType is fxsGroundStart. If the object is true, then the interface is presenting a ring ground to the connected equipm…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.5.6.2.2.1.3
zhoneVaIfFXSTipGround This object contains the incoming tip ground indication. It is only valid when the zvaIfFXSCfgSignalType is fxsGroundStart. If the object is true, then the interface is detecting a tip ground at the interface; otherwis…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.5.6.2.2.1.4

The FXS interface Timing Parameters table. It 
contains the configuration of the various FXS signaling
protocol timing parameters.

zhoneVaIfFXSTimingEntry row .1.3.6.1.4.1.5504.5.6.2.3.1

An entry in the FXS Timing Parameters Table for
each FXS interface.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneVaIfFXSTimingDigitDuration Outgoing DTMF digit duration in milliseconds. The default value of this object is 100 milliseconds. This field is not supported.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.5504.5.6.2.3.1.1
zhoneVaIfFXSTimingInterDigitDuration Outgoing DTMF inter-digit duration in milliseconds. The default value of this object is 100 milliseconds. This field is not supported.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.5504.5.6.2.3.1.2

The FXO standard configuration table. It contains 
FXO configuration parameters, one entry per FXO interface.
The configuration information of this table is set by 
hardware with its default setting or CLI during the hardware 
installation time.

zhoneVaIfFXOCfgEntry row .1.3.6.1.4.1.5504.5.6.3.1.1

An entry in the standard configuration table for
each FXO interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
zhoneVaIfFXOCfgSignalType the signaling type of FXO interface. fxoLoopStart - loop start. fxoGroundStart - ground start. fxodpt- Dial Pulse Terminating , this option allows the unit to attach to incoming one way trunks from a PBX , key system …	Enumerationr/w Enumerated Values: 1 fxoLoopStart 2 fxoGroundStart 3 fxodpt	.1.3.6.1.4.1.5504.5.6.3.1.1.1
zhoneVaIfFXOCfgNumberRings The number of rings detected before closing loop. The default value of this object is 1 ring.	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.5504.5.6.3.1.1.2
zhoneVaIfFXOCfgSupDisconnect Specifies whether a supervisory disconnect signal (CPC) will be presented to the interface when the connected party at the interface hangs up. The default value of this object is 'true'.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.5.6.3.1.1.3
zhoneVaIfFXOCfgDialType Specifies the out dialing type of FXO interface. dtmf - DTMF digit. pulse - pulse. The default value of this object is dtmf(1).	Enumerationr/w Enumerated Values: 1 dtmf 2 pulse	.1.3.6.1.4.1.5504.5.6.3.1.1.4

The Foreign Exchange Office (FXO) interface Status Table.
It contains hook status, ring detection and other states of
the interface.

zhoneVaIfFXOStatusEntry row .1.3.6.1.4.1.5504.5.6.3.2.1

An entry in the status table for each FXO interface.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneVaIfFXOHookStatus This object contains the hook status of FXO interface. onHook - Present the onHook to the connected equipment. offHook - Present the offHook to the connected equipment.	Enumeration Enumerated Values: 1 onHook 2 offHook	.1.3.6.1.4.1.5504.5.6.3.2.1.1
zhoneVaIfFXORingDetect This object contains the ring detect indication. If the value is true, then the interface detects ring from PBX or CO; otherwise, it doesn't.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.5.6.3.2.1.2
zhoneVaIfFXORingGround This object contains the incoming ring ground indication. It is only valid when the zvaIfFXOCfgSignalType is fxoGroundStart. If the object is true, then the interface is presenting a ring ground to the connected equipm…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.5.6.3.2.1.3
zhoneVaIfFXOTipGround This object contains the incoming tip ground indication. It is only valid when the zvaIfFXOCfgSignalType is fxoGroundStart. If the object is true, then the interface is detecting a tip ground at the interface; otherwis…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.5.6.3.2.1.4

The FXO interface Timing Parameters table. It 
contains the configuration of the various FXO signaling
protocol timing parameters.

zhoneVaIfFXOTimingEntry row .1.3.6.1.4.1.5504.5.6.3.3.1

An entry in the FXO Timing Parameters Table for
each FXO interface.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneVaIfFXOTimingDigitDuration Outgoing DTMF digit duration in milliseconds. The default value of this object is 100 msec.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.5504.5.6.3.3.1.1
zhoneVaIfFXOTimingInterDigitDuration Outgoing DTMF inter-digit duration in milliseconds. The default value of this object is 100 msec.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.5504.5.6.3.3.1.2
zhoneVaIfFXOTimingPulseRate Outgoing pulse dialing rate in pulses per second (pps). The default value of this object is 10 pps.	ppsInteger32r/w Constraints: range: 10-20	.1.3.6.1.4.1.5504.5.6.3.3.1.3
zhoneVaIfFXOTimingPulseInterDigitDuration Outgoing pulse dialing inter-digit timing in milliseconds. The default value of this object is 500 milliseconds.	ppsInteger32r/w Constraints: range: 100-1000	.1.3.6.1.4.1.5504.5.6.3.3.1.4

The E&M standard configuration table. It contains 
the current setting of E&M configurable parameters.

zhoneVaIfEMCfgEntry row .1.3.6.1.4.1.5504.5.6.4.1.1

An entry in the standard configuration table for
each E&M tie trunk interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
zhoneVaIfEMCfgSignalType The signaling type of E&M tie trunk interface. winkStart - the calling side seizes the line by going off-hook on its E lead but waits for a short off-hook 'wink' indication on its M lead from …	Enumeration Enumerated Values: 1 winkStart 2 immediateDial 3 delayDial	.1.3.6.1.4.1.5504.5.6.4.1.1.1
zhoneVaIfEMCfgOperation Specify the operation of the E&M signal. twoWires - 2-wire operation. fourWires - 4-wire operation. The default value of this object is twoWires(1).	Enumeration Enumerated Values: 1 twoWires 2 fourWires	.1.3.6.1.4.1.5504.5.6.4.1.1.2
zhoneVaIfEMCfgType Specifies the E&M Lead Signaling type. LEGEND: V = -48V /\/\/ = detector/resister X = normally open relay contact + = normally closed relay contact G = ground SB = Signal Battery SG = Signal Ground…	Enumerationr/w Enumerated Values: 1 typeI 2 typeII 3 typeIII 4 typeIV 5 typeV 6 typeIIE 7 typeIIM 8 typeTO	.1.3.6.1.4.1.5504.5.6.4.1.1.3
zhoneVaIfEMCfgDialType Specifies the out dialing type of E&M interface. dtmf - DTMF digit. pulse - pulse. The default value of this object is dtmf(1).	Enumeration Enumerated Values: 1 dtmf 2 pulse	.1.3.6.1.4.1.5504.5.6.4.1.1.4

The E&M interface Table.  The table contains 
the status of the E&M tie trunk interface.

zhoneVaIfEMStatusEntry row .1.3.6.1.4.1.5504.5.6.4.2.1

An entry in the status table for each E&M interface.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneVaIfEMInSeizureActive This object contains the incoming seizure state of the E&M interface. If the value is true, then the interface has an incoming trunk seizure active; otherwise, it doesn't.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.5.6.4.2.1.1
zhoneVaIfEMOutSeizureActive This object contains the outgoing seizure state of the E&M interface. If the value is true, then the interface has an outgoing trunk seizure active; otherwise, it doesn't.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.5504.5.6.4.2.1.2

The E&M tie trunk Timing Parameters table. It 
contains the configuration of the various E&M signaling
protocol timing parameters.

zhoneVaIfEMTimingEntry row .1.3.6.1.4.1.5504.5.6.4.3.1

An entry in the E&M Timing Parameters Table for
each E&M interface.

Indexes

No indexes recorded

Column	Syntax	OID
zhoneVaIfEMTimingDigitDuration Outgoing DTMF digit duration in milliseconds. The default value of this object is 100 milliseconds.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.5504.5.6.4.3.1.1
zhoneVaIfEMTimingInterDigitDuration Outgoing DTMF inter-digit duration in milliseconds. The default value of this object is 100 milliseconds.	millisecondsInteger32r/w Constraints: range: 50-500	.1.3.6.1.4.1.5504.5.6.4.3.1.2
zhoneVaIfEMTimingPulseRate Outgoing pulse dialing rate in pulses per second (pps). The default value of this object is 10 pps.	ppsInteger32r/w Constraints: range: 10-20	.1.3.6.1.4.1.5504.5.6.4.3.1.3
zhoneVaIfEMTimingPulseInterDigitDuration Outgoing Pulse dialing inter-digit timing in milliseconds. The default value of this object is 500 milliseconds.	millisecondsInteger32r/w Constraints: range: 100-1000	.1.3.6.1.4.1.5504.5.6.4.3.1.4
zhoneVaIfEMTimingClearWaitDuration Time of Inactive seizure signal to declare call cleared. The default value of this object is 400 milliseconds.	millisecondsInteger32r/w Constraints: range: 200-2000	.1.3.6.1.4.1.5504.5.6.4.3.1.5
zhoneVaIfEMTimingMaxWinkWaitDuration Maximum time to wait from the outgoing seizure of the line to the time of sending out a wink-pulse. The default value of this object is 200 milliseconds.	millisecondsInteger32r/w Constraints: range: 100-5000	.1.3.6.1.4.1.5504.5.6.4.3.1.6
zhoneVaIfEMTimingMaxWinkDuration Maximum outgoing wink duration (between the wink-pulse leading edge and trailing edge) for wink start signaling. The default value of this object is 200 milliseconds.	millisecondsInteger32r/w Constraints: range: 100-3000	.1.3.6.1.4.1.5504.5.6.4.3.1.7
zhoneVaIfEMTimingDelayStart Minimum time to wait from outgoing seizure to out-dialing digits for delay start signaling. The default value of this object is 300 milliseconds.	millisecondsInteger32r/w Constraints: range: 20-2000	.1.3.6.1.4.1.5504.5.6.4.3.1.8
zhoneVaIfEMTimingMaxDelayDuration Maximum time to wait from outgoing seizure to out-dialing digits. If the far end does not allow to send digits after the duration specified in the object, a reorder tone will be sent to the calling party. The default va…	millisecondsInteger32r/w Constraints: range: 100-5000	.1.3.6.1.4.1.5504.5.6.4.3.1.9
zhoneVaIfEMTimingMinDelayPulseWidth Minimum delay-dial pulse duration for incoming call. If the value of this object is 0, then no delay-dial is sent to the far end for the incoming call. The default value of this object is 140 milliseconds.	millisecondsInteger32r/w Constraints: range: 140-5000 range: 0-0	.1.3.6.1.4.1.5504.5.6.4.3.1.10