zhoneVaIfCfgTransmitTLP – Zhone-VOICE-ANALOG-IF-MIB

Object

column r/w Enumeration

In case of FXO, it specifies FXO attenuation and default value is 0dB(fxsTtlp0db).
In case of FXS this setting controls the amount of gain or loss added
to a voice signal from CPE before it is encoded to digital PCM.
To increase the signal level, reduce the TTLP setting to lower value.
The default is fxsTtlp0db. Ttlpnummeric selects entering the actual
value in zhoneVaIFCfgTransmitTLPNum.

Context

MIB: Zhone-VOICE-ANALOG-IF-MIB
OID: .1.3.6.1.4.1.5504.5.6.1.1.1.3
Type: column
Access: readwrite
Status: current
Parent: zhoneVaIfCfgEntry
Table: zhoneVaIfCfgTable
Siblings: 12

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	fxsTtlp9db
`2`	fxsTtlp8db
`3`	fxsTtlp7db
`4`	fxsTtlp6db
`5`	fxsTtlp5db
`6`	fxsTtlp4db
`7`	fxsTtlp3db
`8`	fxsTtlp2db
`9`	fxsTtlp1db
`10`	fxsTtlp0db
`11`	fxsTtlpN1db
`12`	fxsTtlpN2db
`13`	fxsTtlpN3db
`14`	tTlpNummeric

Related Objects

Sibling Objects

Object	Type	Syntax	OID
zhoneVaIfCfgImpedance Specifies the terminating impedance of voice analog interfaces. other - none of the following; arbitrary, within limits, for special cases. ohms600Real …	column	Enumeration	`.1.3.6.1.4.1.5504.5.6.1.1.1.1`
zhoneVaIfCfgReceiveTLPNum Receive Transmission Level Point (RTLP) settings control the amount gain or loss added to the incoming signal after it is decoded to analog. to incrase the signal level set the R…	column	dB/10 Integer32	`.1.3.6.1.4.1.5504.5.6.1.1.1.10`
zhoneVaIfCfgTransmitTLPNum Transmit Transmission Level Point controls the amount of gain or loss added to a voice signal from CPE before it is encoded to digital PCM. To increase the signal level, reduce …	column	dB/10 Integer32	`.1.3.6.1.4.1.5504.5.6.1.1.1.11`
zhoneVaIfCfgLoopCurrent To set the loop current value for a subscriber	column	mA Integer32	`.1.3.6.1.4.1.5504.5.6.1.1.1.12`
zhoneVaIfCfgRingVoltage To set the ring voltage for a subscriber.	column	Enumeration	`.1.3.6.1.4.1.5504.5.6.1.1.1.13`
zhoneVaIfCfgReceiveTLP Receive Transmission Level Point (RTLP) settings control the amount gain or loss added to the incoming signal after it is decoded to analog. to increase the signal level set the…	column	Enumeration	`.1.3.6.1.4.1.5504.5.6.1.1.1.2`
zhoneVaIfCfgTrunkConditioning The trunk conditioning setting specifies whether the FXS/FXO port should send the idle pattern to the network upon declaration of a Carrier Group Alarm(CGA) on the WAN link to whi…	column	Enumeration	`.1.3.6.1.4.1.5504.5.6.1.1.1.4`
zhoneVaIfCfgLineType The Card type FXS, FXO, EM, EBS. Entries in the table will be created or deleted on the basis of zhoneVaIfCfgLineType in the zhoneVaIfCfgTable and we are not using rowStatus ent…	column	Enumeration	`.1.3.6.1.4.1.5504.5.6.1.1.1.5`
zhoneVaIfCfgIntegratedDSP Indicates whether the interface has an integrated Digital Signal processing (DSP) unit.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.5504.5.6.1.1.1.6`
zhoneVaIfCfgLineCapabilities The Interface types supported on this interface. This is a bit-map of possible types. This variable can be used to determine zhoneVaIfCfgLineType.	column	Bits	`.1.3.6.1.4.1.5504.5.6.1.1.1.7`
zhoneVaIfCfgMaintenanceMode Indicates the maintenance modes of the Analog voice interface. loopback options for Fxo and Fxs cards (Zhone specific) …	column	Enumeration	`.1.3.6.1.4.1.5504.5.6.1.1.1.8`
zhoneVaIfCfgPCMEncoding alaw(1) :for E1 mulaw(2) : for T1	column	Enumeration	`.1.3.6.1.4.1.5504.5.6.1.1.1.9`