ZYXEL-PORT-AUTHENTICATION-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
1
Rows
1
Columns
12
.1.3.6.1.4.1.890.1.15.3.62.1.2
·
1 row entry
·
12 columns
Uses the zyxel variant from
Command help
/opt/observium/mibs/zyxel.
Walk zyxelPortAuthenticationPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZYXEL-PORT-AUTHENTICATION-MIB' -M '/opt/observium/mibs/zyxel:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZYXEL-PORT-AUTHENTICATION-MIB::zyxelPortAuthenticationPortTable'
The table contains port authentication configuration
An entry contains port authentication configuration.
Indexes
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
Enable/Disable 802.1x port authentication on the port. You must first allow 802.1x authentication on
the Switch before configuring it on each port. |
P-BRIDGE-MIBEnabledStatusr/w Type Values:
|
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.1 |
||||
|
Enable/Disable 802.1x port re-authentication on the port. Specify if a subscriber has to periodically
re-enter his or her username and password to stay connected to the port. |
P-BRIDGE-MIBEnabledStatusr/w Type Values:
|
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.2 |
||||
|
Specify the length of time required to pass before a client has to re-enter his or her username and
password to stay connected to the port. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.3 |
||||
|
Specify the number of seconds the port remains in the HELD state and rejects further authentication
requests from the connected client after a failed authentication exchange. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.4 |
||||
|
Specify the number of seconds the Switch waits for client's response before re-sending an identity
request to the client. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.5 |
||||
|
Specify the number of seconds the Switch waits for client's response to a challenge request before
sending another request. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.6 |
||||
|
Specify the number of times the Switch tries to authenticate client(s) before sending unresponsive
ports to the Guest VLAN. This is set to 2 by default. That is, the Switch attempts to authenticate a client twice. If … |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.7 |
||||
|
Enable/Disable Guest VLAN on the port. Clients that fail authentication are placed in the guest VLAN
and can receive limited services. |
P-BRIDGE-MIBEnabledStatusr/w Type Values:
|
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.8 |
||||
|
Enter the number that identifies the guest VLAN. Make sure this is a VLAN recognized in your network.
A guest VLAN is a pre-configured VLAN on the Switch that allows non-authenticated users to access limited network r… |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.9 |
||||
|
Specify how the Switch authenticates users when more than one user connect to the port (using a hub).
Select Multi-Host to authenticate only the first user that connects to this port. If the first user enters the corr… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.10 |
||||
|
If you set Host-mode to Multi-Secure, specify the maximum number of users that the
Switch will authenticate on this port. |
Integer32r/w Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.11 |
||||
|
Set compound authentication mode at strict mode or loose mode for the switch. Users can use this setting
to choise authentication strict or loose of 802.1x and mac authentication. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.890.1.15.3.62.1.2.1.12 |
