WESTERMO-SW6-MIB Table View

Ethernet Network Interfaces.

cfgNetEthernetTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.2.1.1

Ethernet Network Interfaces.

Indexes

cfgNetEthIndex

Column	Syntax	OID
cfgNetEthIndex Entry index of table.	Integer32 Constraints: range: 0-9	.1.3.6.1.4.1.16177.1.400.1.1.2.1.1.1
cfgNetEthName Name of the ethernet interface. Applies to AP and STA.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.1.1.2
cfgNetEthEnabled Ethernet interface disabled or enabled. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.1.1.3
cfgNetEthBridge If set to other than -1 the interface is part of bridge: * -1: none * 0: br0 * 1: br1 * X: brX Bridges with an index >=100 are special bridges which forward link local traffic. This can be …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.2.1.1.7
cfgNetEthAutoneg Enables or disables auto negotiation of the PHY. * **forced(0):** Forces the speed and duplex defined by `cfgNetEthSpeed`. Only 10Mbit and 100Mbit rates are allowed in forced mode. 1000Mbit requires …	Enumerationr/w Enumerated Values: 0 forced 1 auto	.1.3.6.1.4.1.16177.1.400.1.1.2.1.1.8
cfgNetEthSpeed Defines a bitmask containing the possible speed/duplex combinations. * 0x01 (1) = 10Mbit/Half * 0x02 (2) = 10Mbit/Full * 0x04 (4) = 100Mbit/Half * 0x08 (8) = 100Mbit/Full * 0x20 (32) = 1000Mbit/Full …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.2.1.1.9
cfgNetEthTrunk This entry is active when `cfgNetEthVlanMode` is set to **trunk(0)** or **nativeuntagged(3)**. It specifies which 802.1q vlans are accepted ingress and egress on the respective port. All unspecified vlans…	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.1.1.10
cfgNetEthTag This entry is active when `cfgNetEthVlanMode` is set to **access(1)** or **nativeuntagged(3)**. It specifies which 802.1q VLAN should be used for untagged ingress and egress traffic. Set this entry to -1 to disable it. …	Integer32r/w Constraints: range: -1-4094	.1.3.6.1.4.1.16177.1.400.1.1.2.1.1.11
cfgNetEthVlanMode This entry specifies how the port should behave. * **trunk(0):** A trunk port carries packets on one or more specified VLANs specified in the cfgNetEthTrunk entry. A packet that ingresses on a trunk p…	Enumerationr/w Enumerated Values: 0 trunk 1 access 3 nativeuntagged	.1.3.6.1.4.1.16177.1.400.1.1.2.1.1.12
cfgNetEthLldpEnabled When `cfgLldpEnabled` is enabled, this parameter controls if the interface takes part in LLDP operation. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.1.1.15

WLAN Network Interfaces.

cfgNetWlanTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.2.2.1

WLAN Network Interfaces.

Indexes

cfgNetWlanIndex

Column	Syntax	OID
cfgNetWlanIndex Entry index of Table.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.16177.1.400.1.1.2.2.1.1
cfgNetWlanName Name of the wireless interface. Applies to AP and STA.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.2.1.2
cfgNetWlanEnabled Wireless interface disabled or enabled. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.2.1.3
cfgNetWlanBridge If set to other than -1 the interface is part of bridge: * -1: none * 0: br0 * 1: br1 * X: brX Bridges with an index >=100 are special bridges which forward link local traffic. This can be …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.2.2.1.7
cfgNetWlanTrunk This entry is active when `cfgNetWlanVlanMode` is set to **trunk(0)** or **nativeuntagged(3)**. It specifies which 802.1q vlans are accepted ingress and egress on the respective port. All unspecified vlan…	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.2.1.10
cfgNetWlanTag This entry is active when `cfgNetWlanVlanMode` is set to **access(1)** or **nativeuntagged(3)**. It specifies which 802.1q VLAN should be used for untagged ingress and egress traffic. Set this entry to -1 to disable it.…	Integer32r/w Constraints: range: -1-4094	.1.3.6.1.4.1.16177.1.400.1.1.2.2.1.11
cfgNetWlanVlanMode This entry specifies how the port should behave. * **trunk(0):** A trunk port carries packets on one or more specified VLANs specified in the cfgNetWlanTrunk entry. A packet that ingresses on a trunk …	Enumerationr/w Enumerated Values: 0 trunk 1 access 3 nativeuntagged	.1.3.6.1.4.1.16177.1.400.1.1.2.2.1.12
cfgNetWlanLldpEnabled When `cfgLldpEnabled` is enabled, this parameter controls if the interface takes part in LLDP operation. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.2.1.15

VLAN Network Interfaces.

cfgNetVlanTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.2.3.1

VLAN Network Interfaces.

Indexes

cfgNetVlanIndex

Column	Syntax	OID
cfgNetVlanIndex Entry index of table.	Integer32 Constraints: range: 0-127	.1.3.6.1.4.1.16177.1.400.1.1.2.3.1.1
cfgNetVlanName Name of the VLAN interface. Applies to AP and STA.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.3.1.2
cfgNetVlanEnabled VLAN interface disabled or enabled. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.3.1.3
cfgNetVlanBridge The number of the bridge the VLAN interface is applied to. VLAN interfaces are always of type access. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.2.3.1.7
cfgNetVlanParent Name of the physical parent interface on which the VLAN resides. This entry is only active when the VLAN interface is not part of a bridge (cfgNetVlanBridge = -1). Applies to AP and STA.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.3.1.8
cfgNetVlanVid ID of the VLAN. Applies to AP and STA.	Integer32r/w Constraints: range: 0-4094	.1.3.6.1.4.1.16177.1.400.1.1.2.3.1.9

IP address configuration.

cfgNetIpTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.2.6.1

IP address configuration.

Indexes

cfgNetIpIndex

Column	Syntax	OID
cfgNetIpIndex Entry index of table.	Integer32 Constraints: range: 0-127	.1.3.6.1.4.1.16177.1.400.1.1.2.6.1.1
cfgNetIpEnabled IP disabled or enabled. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.6.1.3
cfgNetIpAddr The IPv4 address (using CIDR notation) of the interface specified in cfgNetIpInterface. Applies to AP and STA.	OctetStringr/w Constraints: range: 9-19	.1.3.6.1.4.1.16177.1.400.1.1.2.6.1.4
cfgNetIpProto This parameter defines which protocol is used to get the IPv4 settings for this interface. * **static(0):** Indicates that the address is manually configured to a specified address given by the IPv4 add…	Enumerationr/w Enumerated Values: 0 static 1 dhcp 2 dhcpForceRenew 3 dhcpForceRelease 4 linkLocal 5 carp	.1.3.6.1.4.1.16177.1.400.1.1.2.6.1.6
cfgNetIpInterface Name of the interface on which the IP resides. Applies to AP and STA.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.6.1.8
cfgNetIpCarpId Id which references the CARP-instance by `cfgNetCarpIndex`. This parameter is only active when `cfgNetIpProto` is set to carp(5). Indicates that the referenced CARP instance processes this IP. …	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.16177.1.400.1.1.2.6.1.10

Redundant IP Addresses with the Common Address Redundancy Protocol (CARP).

cfgNetCarpTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.2.7.1

Redundant IP Addresses with the Common Address Redundancy Protocol (CARP).

Indexes

cfgNetCarpIndex

Column	Syntax	OID
cfgNetCarpIndex Entry index of Table.	Integer32 Constraints: range: 0-15	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.1
cfgNetCarpEnabled CARP interface disabled or enabled. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.3
cfgNetCarpVhid The Virtual Host ID. This is a unique number that is used to identify the redundancy group to other nodes in the group, and to distinguish between groups on the same network. This must be t…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.10
cfgNetCarpPassword The CARP authentication password. This is the password which is used to encrypt the CARP frames when talking to other CARP-enabled hosts in this redundancy group. This must be the same on a…	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.11
cfgNetCarpAdvbase Advertisement base in seconds. This parameter specifies how often to transmit advertisement frames that we're a member of the redundancy group. This time is divided with `cfgNetCarpAdvdivid…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.12
cfgNetCarpAdvskew Advertisement base in 1/255th of a second. This parameter specifies how much to skew the advbase when sending CARP advertisements. By manipulating advskew, the master of a CARP group can be…	Integer32r/w Constraints: range: 0-254	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.13
cfgNetCarpAdvdivider Divider for `cfgNetCarpAdvbase` and `cfgNetCarpAdvskew`. This parameter specifies how much the Advbase and Advskew are divided to speed the algorithm up. With a factor of 1, the Advbase and Advskew are un…	Integer32r/w Constraints: range: 1-100	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.14
cfgNetCarpRatio The dead ratio after which an existing master is considered dead. A slave device will wait: `cfgNetCarpRatio` * (`cfgNetCarpAdvbase` + `cfgNetCarpAdvskew`) before considering…	Integer32r/w Constraints: range: 1-100	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.15
cfgNetCarpPreempt Preempt other masters when the local device is better. Allow hosts within a redundancy group that have a better Advbase and Advskew to preempt the current master. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.16
cfgNetCarpPreemptdemote Preempt other master when they demote theself. Allow hosts within a redundancy group that have a better Advbase and Advskew to preempt the current master when it demotes itself (skew >= 240). …	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.17
cfgNetCarpLocalInterfaceGroup The local carp interface group the carp interface belongs to. When `cfgNetCarpPreempt` or `cfgNetCarpPreemptdemote` is set to enabled, the interface will demote itself (skew = 240) when another interface …	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.18
cfgNetCarpSyncInterface Name of the CARP control interface. This interface is used to transmit and receive CARP advertisements. This interface is required to have its own unique IP address. Applies …	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.19
cfgNetCarpMcastIp Multicast address on which CARP advertisments are transmitted. The default multicast address for CARP is 224.0.0.18. Use this parameter to specify a custom multicast destination. …	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.16177.1.400.1.1.2.7.1.21

MACVLAN Network Interfaces.

cfgNetMacVlanTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.2.9.1

MACVLAN Network Interfaces.

Indexes

cfgNetMacVlanIndex

Column	Syntax	OID
cfgNetMacVlanIndex Entry index of Table.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.16177.1.400.1.1.2.9.1.1
cfgNetMacVlanName Name of the MACVLAN interface. Applies to AP and STA.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.9.1.2
cfgNetMacVlanEnabled MACVLAN interface disabled or enabled. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.9.1.3
cfgNetMacVlanParent Name of the parent interface on which the MACVLAN resides. Applies to AP and STA.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.2.9.1.8
cfgNetMacVlanMac MAC address of the MACVLAN. Set `00:00:00:00:00:00` to use a random MAC address. **Format:** `00:14:5a:02:10:42` Applies to AP and STA.	OctetStringr/w Constraints: range: 17-17	.1.3.6.1.4.1.16177.1.400.1.1.2.9.1.15

WWAN (Cellular) Network Interfaces.
          
Applies to LTE products only.

cfgNetWwanTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.2.11.1

WWAN (Cellular) Network Interfaces.

Applies to LTE products only.

Indexes

cfgNetWwanIndex

Column	Syntax	OID
cfgNetWwanIndex Entry index of Table. Applies to LTE products only.	Integer32 Constraints: range: 0-1	.1.3.6.1.4.1.16177.1.400.1.1.2.11.1.1
cfgNetWwanName Name of the WWAN interface Applies to LTE products only.	OctetString Constraints: range: 4-5	.1.3.6.1.4.1.16177.1.400.1.1.2.11.1.2
cfgNetWwanEnabled WWAN interface disabled or enabled Applies to LTE products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.2.11.1.3
cfgNetWwanPrimarySim SIM parameter entry for the primary SIM This value references the `cfgCellSimIndex` of the desired entry in the `cfgCellSimTable` for the primary SIM. Applies to LTE products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.2.11.1.4
cfgNetWwanSecondarySim SIM parameter entry for the secondary SIM This value references the `cfgCellSimIndex` of the desired entry in the `cfgCellSimTable` for the secondary SIM. Applies to LTE products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.2.11.1.5

Wireless Hardware Modules.

cfgWlanDeviceTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.1.1

Wireless Hardware Modules.

Indexes

cfgWlanDevIndex

Column	Syntax	OID
cfgWlanDevIndex Entry index of table.	Integer32 Constraints: range: 0-1	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.1
cfgWlanDevName Name of the wireless device. Applies to AP and STA.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.2
cfgWlanDevModulation The modulation modes of the physical wireless device are: * **g(2):** This modulation mode uses OFDM data rates up to 54 MBit/s in the frequency band between 2.4 and 2.4835 GHz. It supports the 802.1…	Enumerationr/w Enumerated Values: 2 g 3 bg 4 a 10 ng 12 na 28 ac	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.4
cfgWlanDevBandwidth Wireless Bandwidth Mode specifies the Bandwidth of the Channel. * **bw20(0):** for 20MHz wide channel. * **bw40Plus(1):** for 40MHz wide channel with the side channel on the top. * **bw40Minus(2):** for…	Enumerationr/w Enumerated Values: 0 bw20 1 bw40Plus 2 bw40Minus 3 bwQuarter 4 bwHalf 5 bw80 6 bw160 7 bw8080 8 bwAuto	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.5
cfgWlanDevFrequency Wireless Frequency in MHz. In AP mode, setting the wireless frequency to zero(0) enables the automatic channel selection (ACS) feature. This forces the AP to choose the best channel for operation. …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.6
cfgWlanDevPower Max. limit for wireless output power as effective isotropic radiated power (EIRP) in dBm including array gain and antenna gain. **Note:** This parameter only limits the maximum output power. The effective…	Integer32r/w Constraints: range: 6-50	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.8
cfgWlanDevDistance Maximum distance in meters a client can be apart from the access point. Even though the distance is set in meters, the slot time settings change in 450m steps. Applies to AP and STA. 802.11n products only.	Integer32r/w Constraints: range: 0-114750	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.10
cfgWlanDevRts Frames equal or longer in bytes than this value require a RTS/CTS handshake. RTS/CTS is used in hidden node situations. In 11bg and b mode, these frames are sent in DSSS modulation at 11b data rates. Othe…	Integer32r/w Constraints: range: -1-65535	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.11
cfgWlanDevFragments Frames longer in bytes than this threshold will be fragmented. Fragmentation can be used to reduce the number of retransmissions. The following settings are special * **-1** disable value, …	Integer32r/w Constraints: range: -1-2346	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.12
cfgWlanDevShortRetry Number of times the transmission of the RTS frame will be retried if there is no CTS received from the AP. Applies to AP and STA. 802.11n products only.	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.13
cfgWlanDevLongRetry Number of times the unicast data frames will be retried if there is no ACK from the receiver. Applies to AP and STA. 802.11n products only.	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.14
cfgWlanDevAntennaGain Antenna gain in dBi. If multiple antennas with different gains are connected, the value of the antenna with the highest gain shall be configured. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.15
cfgWlanDevTxAntenna Configure the number of wireless transmission antenna ports. This is a bitmask to enable/disable the chains. **Example** * 1(0001) = A1 (chain 0) enabled * 3(0011) = A1 and A…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.16
cfgWlanDevRxAntenna Configure the number of wireless receiver antennas. This is a bitmask to enable/disable the chains. **Example** * 1(0001) = A1 (chain 0) enabled * 3(0011) = A1 and A2 chain 0…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.17
cfgWlanDevPhy The map between physical device and radio. Applies to AP and STA.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.18
cfgWlanDevHtCapabilities HT capability flags: * [LDPC] = 1 Enable support for LDPC coding * [SHORT-GI-20] = 32 Allow short GI for 20 MHz * [SHORT-GI-40] = 64 Allow short GI for 40 MHz * [TX-STBC] =…	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.24
cfgWlanDevQmrrString A list of rate controller quadruples per queue. Each quadruple consist of (mcs-rate [0-31], tries [0-15], rts_cts [0-1], sgi [0-1]) with 4 entries per queue. 16 values together are for a si…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.26

Wireless Virtual Interfaces.

cfgWlanInterfaceTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.2.1

Wireless Virtual Interface Entry.

Indexes

cfgWlanIfaceIndex

Column	Syntax	OID
cfgWlanIfaceIndex Entry index of table.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.1
cfgWlanIfaceName Name of the virtual wireless interface. Applies to AP and STA.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.2
cfgWlanIfaceDevice Maps the virtual wireless interface to the radio device. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 radio0 1 radio1	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.3
cfgWlanIfaceMode Wireless Operation Mode. Allowed modes are: * **ap(0):** defines the interface as Access Point (AP) * **sta(1):** defines the interface as Station (STA) * **monitor(2):** defines the interf…	Enumerationr/w Enumerated Values: 0 ap 1 sta 2 monitor	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.4
cfgWlanIfaceSsid The Service Set Identifier (SSID) of the wireless interface is the arbitrary name of the wireless network this interface is part of. Applies to AP and STA.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.5
cfgWlanIfaceEncryption Wireless Encryption Mode. Following encryption modes are supported: **open(0)**, **wpa2(3)**, **wpa2eap(6)** and **sae(7)**. **Note:** WPA2 EAP enables 802.1X support. **Note…	Enumerationr/w Enumerated Values: 0 open 3 wpa2 6 wpa2eap 7 sae	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.6
cfgWlanIfacePassword Wireless password if an encryption is in use. Each character in the pass-phrase must have an encoding in the range of 32 to 126 (decimal), inclusive. (IEEE Std. 802.11i-2004, Annex H.4.1) The space charac…	OctetStringr/w Constraints: range: 8-63	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.7
cfgWlanIfacePassiveScanning Wireless Scanning Mode. If the scanning mode is set to active(0) the station will send a probe request to detect available access points if it's allowed by the country code. If the scanning…	Enumerationr/w Enumerated Values: 0 active 1 passive	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.8
cfgWlanIfaceBeaconMiss Number of misses on consecutive beacons before the station will disconnect from the associated access point. Applies to STA. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.9
cfgWlanIfaceDtim This attribute shall specify the number of beacon intervals that shall elapse between transmission of beacons frames containing a TIM element whose DTIM count field is 0. This value is transmitted in the DTIM Period fie…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.10
cfgWlanIfaceBitrates Fixed MCS index for 802.11n rates. Set to -1 to disable (leave on auto). Allows for entering multiple indices divided by a space which are then used in auto rate. This entry is only active when an n-rate …	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.11
cfgWlanIfaceBeaconInterval Time in kus (1.024 ms) between the sending of beacon frames. Applies to AP. 802.11n products only.	Integer32r/w Constraints: range: 15-1000	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.12
cfgWlanIfaceWmeParameter Reference ID to the WME parameter table. Uses all parameters in the cfgWlanWmeTable which have as cfgWlanWmeId the value set here. Applies to AP and STA. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.13
cfgWlanIfaceWmeEnabled Enables usage of the WME parameter table. When using legacy rates (a-rates and g-rates) this is optional. When using n-rates this has to be enabled at all times. Applies to AP. 802.11n prod…	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.14
cfgWlanIfaceScanList Index to specify a frequency list with frequencies to be scanned when in STA mode. To only scan the frequency defined in cfgWlanDevFrequency set to -1. To scan all frequencies allowed by the configured country code set …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.15
cfgWlanIfaceIgnoreBroadcastSsid Send empty SSID in beacons and ignore probe request frames that do not specify the full SSID, i.e., require stations to know SSID. Applies to AP.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.16
cfgWlanIfaceMacaddrAcl Mode of the MAC access control list. * **acceptunlessdeny(0):** Accept unless deny filter. Accept every MAC unless it is on the list defined in `cfgWlanAclBlackTable`. * **denyunlessaccept(1):** Deny …	Enumerationr/w Enumerated Values: 0 acceptunlessdeny 1 denyunlessaccept 2 radius	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.17
cfgWlanIfaceMaxNumSta Maximum number of allowed stations which can connect to this AP. Applies to AP. 802.11n products only.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.18
cfgWlanIfaceBssid BSSID of AP. Set 00:00:00:00:00:00 to use the MAC address stored in the flash of the wireless card itself. If this is the second virtual AP on this card it will automatically set the locally assigned bit.…	OctetStringr/w Constraints: range: 17-17	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.19
cfgWlanIfaceLegacyRates Wireless legacy data rates: * **11b:** 1, 2, 5.5, 11 Mbps * **11a/g:** 6, 9, 12, 18, 24, 36, 48, 54 Mbps The values are interpreted as flags: * auto(0), 1Mbps(1), 2Mbps(2), 5…	Integer32r/w Constraints: range: 0-2048	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.20
cfgWlanIface4addr This option allows to bridge the STA side. When used on the STA, the corresponding AP has to enable this feature as well. Applies to AP and STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.21
cfgWlanIfaceInactivityTimeout If a station does not send anything in ap_max_inactivity seconds, an empty data frame is sent to it in order to verify whether it is still in range. If this frame is not ACKed, the station will be disassociated and then…	Integer32r/w Constraints: range: 15-65535	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.23
cfgWlanIfaceUseVendorSsid When cfgWlanIfaceIgnoreBroadcastSsid is enabled, a passively scanning STA (forced or because of DFS) has no way of detecting the AP it tries to find. On an AP this options adds the hidden SSID as vendor element. On a ST…	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.26
cfgWlanIfaceIeee80211w Controls usage of 802.11w Management Frame Protection (MFP) mechanism. If set to optional on AP, MFP will be enabled only for clients which have it also enabled. If set to required, only MFP enabled clients will be able…	Enumerationr/w Enumerated Values: 0 disabled 1 optional 2 required	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.30
cfgWlanIfaceIeee80211wMaxTimeout 802.11w Management Frame Protection (MFP) Association SA query maximum timeout (in TU = 1.024 ms; for MFP) (maximum time to wait for a SA query response) Applies to AP.	Integer32r/w Constraints: range: 1-4000	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.31
cfgWlanIfaceIeee80211wRetryTimeout 802.11w Management Frame Protection (MFP) Association SA query retry timeout (in TU = 1.024 ms; for MFP) (time between two subsequent SA query requests) Applies to AP.	Integer32r/w Constraints: range: 1-4000	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.32
cfgWlanIfaceAcsList Index to specify a frequency list for Automated Channel Selection (ACS) support when in AP mode. To disable set to -1. Applies to AP. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.40
cfgWlanIfaceNeighbourReport Enable/disable neighbour reporting. A STA can request the neighbour table from an AP and use this information to improve its handoff decision. Applies to AP. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.60
cfgWlanIfaceNeighbourParameter Reference ID to the neighbour table. Uses all neighbours in the `cfgWlanNeighbourTable` which have as `cfgWlanNeighbourId` the value set here. Applies to AP. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.61
cfgWlanIfaceL2nat This option allows to bridge the STA side. It is intended to be used in setups where the STA is doing handoff between multiple APs. There is no configuration on the APs required. This is an alternative to…	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.80
cfgWlanIfaceL2natLearningMode From which type of frames the IP/MAC table may be learned. When `cfgWlanIfaceL2nat` is enabled a table of the association between IP-addresses and MAC-addresses is kept. This options specifies from which …	Enumerationr/w Enumerated Values: 0 both 1 arp	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.81
cfgWlanIfaceL2natDefaultDestination This option defines the default MAC address to send frames to. Whenever a unicast frame is received for which no learned entry exists, or which isn't a L3 frame (e.g a custom L2 protocol), the frame will …	OctetStringr/w Constraints: range: 17-17	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.82
cfgWlanIfaceTimeAdvertisement Enable AP to include local time in association response frames. This provides a mean for APs to distribute its local system time to STAs in setups where devices have no RTC and start up with an invalid sy…	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.90
cfgWlanIfaceApIsolate Enable AP clients isolation. If enabled, clients connected to this AP can't communicate to each other. Applies to AP.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.2.1.100

Wireless handoff parameters.
          
Applies to STA.  802.11n products only.

cfgWlanHandoffTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.3.1

Wireless handoff parameters entry.

Applies to STA. 802.11n products only.

Indexes

cfgWlanHoIndex

Column	Syntax	OID
cfgWlanHoIndex Entry index of table. Applies to STA. 802.11n products only.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.1
cfgWlanHoIfaceName Name of the virtual wireless interface. Applies to STA. 802.11n products only.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.2
cfgWlanHoProfile Handoff profile. * **t2gv1(1):** Train to Ground v1 * **t2gv2(2):** Train to Ground v2 * **t2gv2fg(3):** Train to Ground v2 fg scan * **t2gv3(4):** Train to Ground v3 (RSSI high/low, Distance near/far) …	Enumerationr/w Enumerated Values: 1 t2gv1 2 t2gv2 3 t2gv2fg 4 t2gv3	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.3
cfgWlanHoScanningLevel Scanning level in RSSI. When the RSSI level of the currently connected access point drops below the value configured in this parameter, the STA will scan for better access points on all frequencies specif…	Integer32r/w Constraints: range: 0-95	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.5
cfgWlanHoBeacons Number of beacons which have to be received from an AP before a decision about handoff is allowed. Essentially forces the STA to stay on a given AP for <cfgWlanHoBeacons * cfgWlanIfaceBeaconInterval> before doing anothe…	Integer32r/w Constraints: range: 4-20	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.6
cfgWlanHoRecovery Recovery time in milliseconds after a successful handoff. During this time no further handoff will be executed. Applies to STA. 802.11n products only.	Integer32r/w Constraints: range: 0-2000	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.7
cfgWlanHoFilterMode RSSI filter mode. * **short(0):** high responsive static IIR RSSI filter. * **long(1):** configurable IIR RSSI filter. Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 short 1 long	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.9
cfgWlanHoFilterLongX IIR Filter Parameter x for long RSSI filter. Applies to STA. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.10
cfgWlanHoFilterLongY IIR Filter Parameter y for long RSSI filter. Applies to STA. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.11
cfgWlanHoScanRateLimitTime Time in milliseconds (4ms steps) in which a number of attempts to connect to an AP can be tried. Applies to STA. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.12
cfgWlanHoScanRateLimitTries Number of attempts to connect to an AP before the AP is blacklisted and ignored. The AP is removed from the blacklist after `cfgWlanHoScanRateLimitTime` since the first attempt. Applies to STA. 802.11n pr…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.13
cfgWlanHoPassiveChanTime Time in milliseconds (4ms steps) we stay on a channel during passive scanning and wait for beacons. Applies to STA. 802.11n products only.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.16
cfgWlanHoLevelLow Scanning level low in RSSI. When the RSSI level to the current connected AP is below this value, perform a handoff to the next AP. This value is only active when `cfgWlanHoProfile` is set t…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.18
cfgWlanHoLevelHigh Scanning level high in RSSI. When the RSSI level to the current connected AP is above this value, perform a handoff to the next AP. This value is only active when `cfgWlanHoProfile` is set …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.19
cfgWlanHoDistanceNear Distance level near. When the measured distance to the current connected AP is below this value in meters, perform a handoff to the next AP. This value is only active when `cfgWlanHoProfile…	Integer32r/w Constraints: range: 0-114750	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.20
cfgWlanHoDistanceFar Distance level far. When the measured distance to the current connected AP is above this value in meters, perform a handoff to the next AP. This value is only active when `cfgWlanHoProfile`…	Integer32r/w Constraints: range: 0-114750	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.21
cfgWlanHoDistanceMeasurementPeriod Distance ranging measurement period in milliseconds. Setting zero disables distance handoff. This value is only active when `cfgWlanHoProfile` is set to T2Gv3. Typical ranging measurement p…	Integer32r/w Constraints: range: 0-100000	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.22
cfgWlanHoDistanceFilterX IIR Filter Parameter x for distance measurement. This value is only active when `cfgWlanHoProfile` is set to T2Gv3. Applies to STA. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.23
cfgWlanHoDistanceFilterY IIR Filter Parameter y for distance measurements. This value is only active when `cfgWlanHoProfile` is set to T2Gv3. Applies to STA. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.3.1.24

Frequency list entry.

cfgWlanFreqTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.4.1

Frequency list entry.

Indexes

cfgWlanFIndex

Column	Syntax	OID
cfgWlanFIndex Entry index of table	Integer32 Constraints: range: 0-23	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.1
cfgWlanFFreq0 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.2
cfgWlanFFreq1 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.3
cfgWlanFFreq2 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.4
cfgWlanFFreq3 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.5
cfgWlanFFreq4 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.6
cfgWlanFFreq5 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.7
cfgWlanFFreq6 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.8
cfgWlanFFreq7 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.9
cfgWlanFFreq8 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.10
cfgWlanFFreq9 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.11
cfgWlanFFreq10 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.12
cfgWlanFFreq11 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.13
cfgWlanFFreq12 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.14
cfgWlanFFreq13 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.15
cfgWlanFFreq14 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.16
cfgWlanFFreq15 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.17
cfgWlanFFreq16 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.18
cfgWlanFFreq17 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.19
cfgWlanFFreq18 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.20
cfgWlanFFreq19 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.21
cfgWlanFFreq20 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.22
cfgWlanFFreq21 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.23
cfgWlanFFreq22 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.24
cfgWlanFFreq23 Frequency in MHz, 0 is interpreted as empty. Applies to AP and STA.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.4.1.25

Wireless Multimedia Extensions (WME) based on the IEEE 802.11e
standard. It provides basic Quality of Service (QoS) features to
IEEE 802.11 networks.
          
The levels of priority in EDCA are called access categories (ACs).
The contention window (CW) can be set according to the traffic
expected for each access category, with a wider window needed for
categories with heavier traffic.
          
Applies to AP. 802.11n products only.

cfgWlanWmeTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.5.1

WME entry.

Indexes

cfgWlanWmeIndex

Column	Syntax	OID
cfgWlanWmeIndex Entry index of table.	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.1
cfgWlanWmeId ID of the WME parameter table. The virtual wireless interface references to this ID. Applies to AP. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.2
cfgWlanWmeAc Access category (background, besteffort, video, voice). Applies to AP. 802.11n products only.	Enumerationr/w Enumerated Values: 0 none 1 background 2 besteffort 3 video 4 voice	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.3
cfgWlanWmeCwMin Contention window minimum in exponential form. Is used on STAs connected to this AP: `Real value = (2^n)-1` Applies to AP. 802.11n products only.	Integer32r/w Constraints: range: 0-12	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.4
cfgWlanWmeCwMax Contention window maximum in exponential form. Is used on STAs connected to this AP: `Real value = (2^n)-1` Applies to AP. 802.11n products only.	Integer32r/w Constraints: range: 0-12	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.5
cfgWlanWmeAifs Arbitration inter-frame space. Is used on STAs connected to this AP. Applies to AP. 802.11n products only.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.6
cfgWlanWmeTxOpMax A Transmit Opportunity (TXOP) is a bound time interval during which a station can send as many frames as possible (as long as the duration of the transmissions does not exceed the maximum duration of the TXOP). A value …	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.7
cfgWlanWmeApCwMin Contention window minimum. Allowed values: 1, 3, 7, 15, 31, 63, 127, 255, 511, 1023. Is used on the AP itself. Applies to AP. 802.11n products only.	Integer32r/w Constraints: range: 1-1023	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.8
cfgWlanWmeApCwMax Contention window maximum. Allowed values: 1, 3, 7, 15, 31, 63, 127, 255, 511, 1023 cwMax has to be greater or equal cwMin. Is used on the AP itself. Applies to AP. 802.11n p…	Integer32r/w Constraints: range: 1-1023	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.9
cfgWlanWmeApAifs Arbitration inter-frame space. Is used on the AP itself. Applies to AP.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.10
cfgWlanWmeApBurst Maximum length for bursting (equivalent to TxOpLimit). This value is in units of 32us. Is used on the AP itself. Applies to AP. 802.11n products only.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.16177.1.400.1.1.3.5.1.11

Wireless Handoff Debug Parameters.

cfgWlanDbgTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.6.1

Wireless Handoff Debug Parameters Entry.

Indexes

cfgWlanDbgIndex

Column	Syntax	OID
cfgWlanDbgIndex Entry index of table.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.1
cfgWlanDbgIfaceName Name of the virtual wireless interface. Applies to STA. 802.11n products only.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.2
cfgWlanDbgHandoff Persistent default value to enable/disable the handoff messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.3
cfgWlanDbgScan Persistent default value to enable/disable the scan messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.4
cfgWlanDbgMlme Persistent default value to enable/disable the MLME messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.5
cfgWlanDbgEvents Persistent default value to enable/disable the events messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.6
cfgWlanDbgBeaconrssi Persistent default value to enable/disable the beacon RSSI messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.7
cfgWlanDbgAckrssi Persistent default value to enable/disable the ACK RSSI messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.8
cfgWlanDbgBeaconfiltered Persistent default value to enable/disable the beacon filtered RSSI messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.9
cfgWlanDbgRatelimit Persistent default value to enable/disable the rate limiter messages in syslog. These log messages are subject to change. DO NOT PARSE! Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.10
cfgWlanDbgLinkmonitor Periodically sends a trap containing link information of all connected devices on this interface. Applies to both AP and STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.11
cfgWlanDbgBeacontsf Persistent default value to enable/disable the beacon RSSI messages in syslog. These log messages are subject to change. DO NOT PARSE! TS files is the TSF of the station. Applies to STA. 802.11n products …	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.12
cfgWlanDbgRange Persistent setting for distance measurement messages in syslog. **Note:** Distance value is not in meters. Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.13
cfgWlanDbgReports Persistent setting for periodical WLAN debug data reporting. Applies to STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.6.1.14

Wireless MAC Access Control Whitelist

cfgWlanAclWhiteTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.7.1

Wireless MAC Access Control Whitelist Entry.

Indexes

cfgWlanAclWhiteIndex

Column	Syntax	OID
cfgWlanAclWhiteIndex Entry index of table.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.16177.1.400.1.1.3.7.1.1
cfgWlanAclWhiteEnabled Enable this entry in the ACL. Applies to AP.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.7.1.2
cfgWlanAclWhiteInterface Name of the virtual wireless interface on which this entry is active. Applies to AP.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.7.1.3
cfgWlanAclWhiteAddr MAC address in the ACL. **Format:** `00:14:5a:02:10:42` Applies to AP.	OctetStringr/w Constraints: range: 17-17	.1.3.6.1.4.1.16177.1.400.1.1.3.7.1.4
cfgWlanAclWhiteMask Mask of the MAC address to specify ranges of MAC addresses. To be used like CIDR notation of IP addresses. Applies to AP.	Integer32r/w Constraints: range: 0-48	.1.3.6.1.4.1.16177.1.400.1.1.3.7.1.5

Wireless MAC Access Control Blacklist.

cfgWlanAclBlackTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.8.1

Wireless MAC Access Control Blacklist Entry.

Indexes

cfgWlanAclBlackIndex

Column	Syntax	OID
cfgWlanAclBlackIndex Entry index of table.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.16177.1.400.1.1.3.8.1.1
cfgWlanAclBlackEnabled Enable this entry in the ACL. Applies to AP.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.8.1.2
cfgWlanAclBlackInterface Name of the virtual wireless interface on which this entry is active. Applies to AP.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.8.1.3
cfgWlanAclBlackAddr MAC address in the ACL. **Format:** `00:14:5a:02:10:42` Applies to AP.	OctetStringr/w Constraints: range: 17-17	.1.3.6.1.4.1.16177.1.400.1.1.3.8.1.4
cfgWlanAclBlackMask Mask of the MAC address to enable the use of ranges of MAC addresses. To be used like CIDR notation of IP addresses. Applies to AP.	Integer32r/w Constraints: range: 0-48	.1.3.6.1.4.1.16177.1.400.1.1.3.8.1.5

Wireless 802dot1x.

cfgWlan802dot1xTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.10.1

Wireless 802dot1x entry.

Indexes

cfgWlan802dot1xIndex

Column	Syntax	OID
cfgWlan802dot1xIndex Entry index of table	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.1
cfgWlan802dot1xName Name of the virtual wireless interface. Applies to AP and STA.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.2
cfgWlan802dot1xOwnIpAddr The own IP address of the authenticator. This field is used as NAS-IP-Address RADIUS attribute. Set this to the IP address with which the authenticator will communicate with the RADIUS server. Applies to …	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.3
cfgWlan802dot1xAuthServerParameter Reference ID to the radius auth server table. Uses all parameters in the cfgWlan802dot1xAuthServerTable which have as cfgWlan802dot1xAuthSrvId the value set here. Applies to AP.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.4
cfgWlan802dot1xAcctServerParameter Reference ID to the radius acct server table. Uses all parameters in the cfgWlan802dot1xAcctServerTable which have as cfgWlan802dot1xAcctSrvId the value set here. Applies to AP.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.5
cfgWlan802dot1xRetryPrimaryInterval Retry interval for trying to return to the primary RADIUS server (in seconds). RADIUS client code will automatically try to use the next server when the current server is not replying to requests. If this interval is se…	Integer32r/w Constraints: range: 0-86400	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.6
cfgWlan802dot1xInterimAccountingInterval Interim accounting update interval in seconds. If this is set (larger than 0) and acct_server is configured, hostapd will send interim accounting updates every N seconds. Set to 0 to disable. …	Integer32r/w Constraints: range: 0-86400	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.7
cfgWlan802dot1xNasId Optional NAS identifier string for RADIUS messages. When used, this should be unique to the NAS within the scope of the RADIUS server. For example, a fully qualified domain name can be used here. When using IEEE 802.11r…	OctetStringr/w Constraints: range: 1-48	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.8
cfgWlan802dot1xEapType Specify the EAP type. Applies to STA.	Enumerationr/w Enumerated Values: 0 tls 1 peap 2 ttls	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.9
cfgWlan802dot1xIdentity The identity string for EAP. Applies to STA.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.10
cfgWlan802dot1xClientKeyPassword The password to unlock the private key. This is only required if the key is encrypted. Applies to STA.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.17
cfgWlan802dot1xTlsControlParams Bitfield to control TLS behaviour. * **0x1** ignore certificate validity time * **0x2** ignore ca certificate Applies to STA.	Integer32r/w Constraints: range: 0-3	.1.3.6.1.4.1.16177.1.400.1.1.3.10.1.18

Wireless 802dot1x AuthServer.

cfgWlan802dot1xAuthServerTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.11.1

Wireless 802dot1x AuthServer entry.

Indexes

cfgWlan802dot1xAuthSrvIndex

Column	Syntax	OID
cfgWlan802dot1xAuthSrvIndex Entry index of table.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.16177.1.400.1.1.3.11.1.1
cfgWlan802dot1xAuthSrvEnabled Enable this entry in the auth server list. Applies to AP.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.11.1.2
cfgWlan802dot1xAuthSrvId ID of the authorisation server table. The configuration item cfgWlan802dot1xAuthServerParameter references to this ID. Applies to AP.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.11.1.3
cfgWlan802dot1xAuthSrvIpAddr IP of the RADIUS server against which will be authenticated. Applies to AP.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.16177.1.400.1.1.3.11.1.4
cfgWlan802dot1xAuthSrvPort Port of the RADIUS server against which will be authenticated. Applies to AP.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.11.1.5
cfgWlan802dot1xAuthSrvSharedSecret Password to connect to the specified RADIUS server. Applies to AP.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.11.1.6

Wireless 802dot1x AcctServer.

cfgWlan802dot1xAcctServerTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.12.1

Wireless 802dot1x AcctServer entry.

Indexes

cfgWlan802dot1xAcctSrvIndex

Column	Syntax	OID
cfgWlan802dot1xAcctSrvIndex Entry index of table.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.16177.1.400.1.1.3.12.1.1
cfgWlan802dot1xAcctSrvEnabled Enable this entry in the acct server list. Applies to AP.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.12.1.2
cfgWlan802dot1xAcctSrvId ID of the accounting server table. The configuration item cfgWlan802dot1xAcctServerParameter refers to this ID. Applies to AP.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.12.1.3
cfgWlan802dot1xAcctSrvIpAddr IP of the RADIUS accounting server. Set to 0.0.0.0 to disable. Applies to AP.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.16177.1.400.1.1.3.12.1.4
cfgWlan802dot1xAcctSrvPort Port of the RADIUS accounting server. Applies to AP.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.12.1.5
cfgWlan802dot1xAcctSrvSharedSecret Password to connect to the specified RADIUS accounting server. Applies to AP.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.12.1.6

Wireless 802dot11r.

cfgWlan802dot11rTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.13.1

Wireless 802dot11r Entry.

Indexes

cfgWlan802dot11rIndex

Column	Syntax	OID
cfgWlan802dot11rIndex Entry index of Table.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.1
cfgWlan802dot11rName Name of the virtual wireless interface. Applies to AP and STA. 802.11n products only.	OctetString Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.2
cfgWlan802dot11rEnabled Enable usage of 802.11r on this device. Applies to AP and STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.3
cfgWlan802dot11rMobilityDomain Mobility Domain identifier (dot11FTMobilityDomainID, MDID) MDID is used to indicate a group of APs (within an ESS, i.e., sharing the same SSID) between which a STA can use Fast BSS Transition. 2-octet identifier as a he…	OctetStringr/w Constraints: range: 4-4	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.4
cfgWlan802dot11rPmkR0KeyHolderIdentifier PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID). Configure this in the field cfgWlan802dot1xNasId. Applies to AP. 802.11n products only.	OctetString Constraints: range: 1-48	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.5
cfgWlan802dot11rPmkR0Lifetime PMK-RO lifetime in seconds (dot11FTR0KeyLifetime). When Session-Timeout attribute is provided by RADIUS server, then min(Session-Timeout, cfgWlan802dot11rPmkR0Lifetime) is used. **Ranges** …	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.6
cfgWlan802dot11rPmkR1KeyHolderIdentifier PMK-R1 Key Holder identifier (dot11FTR0KeyHolderID). 6-octet identifier as a hex string. This may be the same as the local MAC address. Default magic number 000102030405 means use own mac address (bssid).…	OctetStringr/w Constraints: range: 12-12	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.7
cfgWlan802dot11rPmkR1Push Whether PMK-R1 push is enabled at R0KH. * **0** do not push PMK-R1 to all configured R1KHs (default). * **1** push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived. Applies t…	Enumerationr/w Enumerated Values: 0 donotpush 1 push	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.9
cfgWlan802dot11rR0KHParameter Reference ID to the R0KH parameter table. Uses all parameters in the cfgWlan802dot11rR0KHTable which have as cfgWlan802dot11rR0KHTblId the value set here. Applies to AP. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.10
cfgWlan802dot11rR1KHParameter Reference ID to the R1KH parameter table. Uses all parameters in the cfgWlan802dot11rR1KHTable which have as cfgWlan802dot11rR1KHTblId the value set here. Applies to AP. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.11
cfgWlan802dot11rExpirationEnabled Enable/disable PMK-R0/-R1 expiration forcing. If set to **enabled(1)**, AP forces PMK-R0s and PMK-R1s expiration once a day (see `cfgWlan802dot11rExpirationTime`). Applies to AP. 802.11n pr…	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.12
cfgWlan802dot11rExpirationTime Daily PMK-R0/-R1 expiration time. Define time (hour:minute) at which PMK-R0s and PMK-R1s expiration is daily forced (if `cfgWlan802dot11rExpirationEnabled` is **enabled(1)**). The time is r…	OctetStringr/w Constraints: range: 5-5	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.13
cfgWlan802dot11rVlan The 802.1q VLAN tag of 802.11r backbone traffic. Defines the VLAN tag with which all 802.11r managment frames (ethertype 0x88b7) are transmitted on the backbone. Setting a value of 0 disabl…	Integer32r/w Constraints: range: 0-4094	.1.3.6.1.4.1.16177.1.400.1.1.3.13.1.14

Wireless 802dot11r R0KH.
          
List of R0KHs in the same Mobility Domain. This list is used to map
R0KH-ID (NAS Identifier) to a destination MAC address when
requesting PMK-R1 key from the R0KH that the STA used during the
Initial Mobility Domain Association.
          
**Format:** `<MAC address> <NAS Identifier> <128-bit key as hex string>`
          
**Example**
          
~~~
r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f
r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff
~~~
          
Applies to AP. 802.11n products only.

cfgWlan802dot11rR0KHTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.14.1

Wireless 802dot11r R0KH Entry.

Indexes

cfgWlan802dot11rR0KHIndex

Column	Syntax	OID
cfgWlan802dot11rR0KHIndex Entry index of Table.	Integer32 Constraints: range: 0-511	.1.3.6.1.4.1.16177.1.400.1.1.3.14.1.1
cfgWlan802dot11rR0KHId ID of the R0KH table. The configuration item cfgWlan802dot11rR0KHParameter references to this ID. Applies to AP. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.14.1.2
cfgWlan802dot11rR0KHEnabled Enable this entry in the R0KH list. Applies to AP. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.14.1.3
cfgWlan802dot11rR0KHDestinationMac MAC addresses of all possible R0KHs from which PMK-R1 can be requested. **Format:** `02:01:02:03:04:05` Applies to AP. 802.11n products only.	OctetStringr/w Constraints: range: 17-17	.1.3.6.1.4.1.16177.1.400.1.1.3.14.1.4
cfgWlan802dot11rR0KHHID NAS Identifier of all R0KHs to map to the MAC address. See the field: cfgWlan802dot11rPmkR0KeyHolderIdentifier. Applies to AP. 802.11n products only.	OctetStringr/w Constraints: range: 1-48	.1.3.6.1.4.1.16177.1.400.1.1.3.14.1.5
cfgWlan802dot11rR0KHKey Static Key of the R0KH. Connecting R1KHs need to have this key configured. **Format:** `000102030405060708090a0b0c0d0e0f` Applies to AP. 802.11n products only.	OctetStringr/w Constraints: range: 32-32	.1.3.6.1.4.1.16177.1.400.1.1.3.14.1.6

Wireless 802dot11r R1KH.
          
List of R1KHs in the same Mobility Domain
This list is used to map R1KH-ID to a destination MAC address when
sending PMK-R1 key from the R0KH. This is also the list of
authorized R1KHs in the MD that can request PMK-R1 keys.
          
**Format:** `<MAC address> <R1KH-ID> <128-bit key as hex string>`
          
**Example**
          
~~~
r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f
r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff
~~~
          
Applies to AP. 802.11n products only.

cfgWlan802dot11rR1KHTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.15.1

Wireless 802dot11r R1KH Entry.

Indexes

cfgWlan802dot11rR1KHIndex

Column	Syntax	OID
cfgWlan802dot11rR1KHIndex Entry index of Table.	Integer32 Constraints: range: 0-511	.1.3.6.1.4.1.16177.1.400.1.1.3.15.1.1
cfgWlan802dot11rR1KHId ID of the R1KH table. The configuration item cfgWlan802dot11rR1KHParameter references to this ID. Applies to AP.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.15.1.2
cfgWlan802dot11rR1KHEnabled Enable this entry in the R1KH list. Applies to AP. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.15.1.3
cfgWlan802dot11rR1KHDestinationMac MAC addresses of all R1KHs which can reqest PMK-R1 from the local R0KH. **Format:** `02:01:02:03:04:05` Applies to AP.	OctetStringr/w Constraints: range: 17-17	.1.3.6.1.4.1.16177.1.400.1.1.3.15.1.4
cfgWlan802dot11rR1KHHID PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID) 6-octet identifier as a hex string to map to the MAC. This may be the same as the destination MAC. See the field cfgWlan802dot11rPmkR1KeyHolderIdentifie…	OctetStringr/w Constraints: range: 17-17	.1.3.6.1.4.1.16177.1.400.1.1.3.15.1.5
cfgWlan802dot11rR1KHKey Static Key of the R0KH. These keys are used wenn sending updates to R1KHs from the local R0KH. The respective key has to match the respective entry on the target in the field cfgWlan802dot11rR0KHKey. …	OctetStringr/w Constraints: range: 32-32	.1.3.6.1.4.1.16177.1.400.1.1.3.15.1.6

Hostapd Neighbour Table.

cfgWlanNeighbourTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.3.16.1

Hostapd Neighbour Table Entry.

Indexes

cfgWlanNeighbourIndex

Column	Syntax	OID
cfgWlanNeighbourIndex Entry index of Table.	Integer32 Constraints: range: 0-511	.1.3.6.1.4.1.16177.1.400.1.1.3.16.1.1
cfgWlanNeighbourId ID of the neighbour table. The configuration item `cfgWlanIfaceNeighbourParameter` references to this ID. Applies to AP. 802.11n products only.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.16177.1.400.1.1.3.16.1.2
cfgWlanNeighbourEnabled Enable this entry in the list. Applies to AP. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.3.16.1.3
cfgWlanNeighbourBSSID BSSID (MAC address) of the neighbour. **Format:** `00:14:5a:02:10:42` Applies to AP.	OctetStringr/w Constraints: range: 17-17	.1.3.6.1.4.1.16177.1.400.1.1.3.16.1.4
cfgWlanNeighbourFrequency Frequency in MHz of the neighbour. Applies to AP. 802.11n products only.	Integer32r/w Constraints: range: 1-6000	.1.3.6.1.4.1.16177.1.400.1.1.3.16.1.5

Static routes

cfgRouteTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.4.2.1

Static route.

Indexes

cfgRouteTableIndex

Column	Syntax	OID
cfgRouteTableIndex Entry index of table.	Integer32 Constraints: range: 0-265	.1.3.6.1.4.1.16177.1.400.1.1.4.2.1.1
cfgRouteTableEnabled Enable/Disable this route entry. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.4.2.1.2
cfgRouteTableDestinationNetwork Destination network in CIDR notation. Applies to AP and STA.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.16177.1.400.1.1.4.2.1.3
cfgRouteTableGateway Gateway to destination network. Applies to AP and STA.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.16177.1.400.1.1.4.2.1.5
cfgRouteTableSource Source for traffic to destination network. Optional. Use only if you have multiple possible sources. Applies to AP and STA.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.16177.1.400.1.1.4.2.1.6
cfgRouteTableCarpId The CARP instance which brings this route up. Has to be set to -1 when this is a normal route and should not be handled by a CARP instance. All routes which have a value 0..15 are brought up by the respec…	Integer32r/w Constraints: range: -1-15	.1.3.6.1.4.1.16177.1.400.1.1.4.2.1.8

Static multicast routes.

cfgMRouteTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.4.3.1

Static multicast routes.

Indexes

cfgMRouteTableIndex

Column	Syntax	OID
cfgMRouteTableIndex Entry index of table.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.16177.1.400.1.1.4.3.1.1
cfgMRouteTableEnabled Enable/Disable this multicast route entry. Applies to AP and STA.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.4.3.1.2
cfgMRouteTableInput Input interface. Applies to AP and STA.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.4.3.1.3
cfgMRouteTableSource Unicast source address to listen to. If it is set to 0.0.0.0 all multicast traffic will be forwarded. Applies to AP and STA.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.16177.1.400.1.1.4.3.1.4
cfgMRouteTableGroup Multicast group to forward. Applies to AP and STA.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.16177.1.400.1.1.4.3.1.5
cfgMRouteTableOutput Output interface(s). Can be a list of interface names separated by spaces. Applies to AP and STA.	OctetStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.16177.1.400.1.1.4.3.1.6

Mapping table from DSCP class selector (IP TOS) to
wireless priority (TID).

cfgQosDscpToTidMapTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.6.2.1

QoS DSCP to TID Mapping Table Entry.

Indexes

cfgQosDscpToTidMapTableIndex

Column	Syntax	OID
cfgQosDscpToTidMapTableIndex QoS DSCP to TID Mapping Table Index.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.16177.1.400.1.1.6.2.1.1
cfgQosDscpToTidMapValue Layer 2 priorities for IP precedence values 0-7. Applies to AP and STA. 802.11n products only.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.16177.1.400.1.1.6.2.1.2

Mapping table from layer 2 priorities (802.1p)
to wireless priority (TID).

cfgQosVlanToTidMapTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.6.3.1

QoS Vlan to TID Priority Table Entry.

Indexes

cfgQosVlanToTidMapTableIndex

Column	Syntax	OID
cfgQosVlanToTidMapTableIndex QoS Vlan to TID Priority Table Entry Index.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.16177.1.400.1.1.6.3.1.1
cfgQosVlanToTidMapValue Layer 2 priorities for VLAN priorities 0-7. Applies to AP and STA. 802.11n products only.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.16177.1.400.1.1.6.3.1.2

Mapping table from IP header (Source, Destination, Protocol, Port),
to wireless priority (TID).

cfgQosIpToTidMapTableEntry row .1.3.6.1.4.1.16177.1.400.1.1.6.4.1

IP to TID Priority Table Entry.

Indexes

cfgQosIpToTidMapTableIndex

Column	Syntax	OID
cfgQosIpToTidMapTableIndex IP to TID Priority Table Index.	Integer32 Constraints: range: 0-127	.1.3.6.1.4.1.16177.1.400.1.1.6.4.1.1
cfgQosIpToTidMapSrcNet Source network for ip prioritization rule, in CIDR format. Applies to AP and STA. 802.11n products only.	OctetStringr/w	.1.3.6.1.4.1.16177.1.400.1.1.6.4.1.2
cfgQosIpToTidMapDestNet Destination network for ip prioritization rule, in CIDR format. Applies to AP and STA. 802.11n products only.	OctetStringr/w	.1.3.6.1.4.1.16177.1.400.1.1.6.4.1.3
cfgQosIpToTidMapProto Protocol for ip prioritization rule, allowed protocols are: **any(0)**, **udp(1)** or **tcp(2)**. Applies to AP and STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 any 1 udp 2 tcp	.1.3.6.1.4.1.16177.1.400.1.1.6.4.1.4
cfgQosIpToTidMapSrcPort Source port for ip prioritization rule, use port -1 to match any port. This setting can only be used if the protocol is set to udp or tcp. Applies to AP and STA. 802.11n products only.	Integer32r/w Constraints: range: -1-65536	.1.3.6.1.4.1.16177.1.400.1.1.6.4.1.5
cfgQosIpToTidMapDestPort Destination port for ip prioritization rule, use port -1 to match any port. This setting can only be used if the protocol is set to udp or tcp. Applies to AP and STA. 802.11n products only.	Integer32r/w Constraints: range: -1-65536	.1.3.6.1.4.1.16177.1.400.1.1.6.4.1.6
cfgQosIpToTidMapPrecedence Precedence to set for ip prioritization rule. Applies to AP and STA. 802.11n products only.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.16177.1.400.1.1.6.4.1.7
cfgQosIpToTidMapEnabled Enable/disable ip prioritisation rules. Applies to AP and STA. 802.11n products only.	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.16177.1.400.1.1.6.4.1.8