LUM-CLIENT-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
4
Rows
4
Columns
239

clientIfTable

table
.1.3.6.1.4.1.8708.2.27.2.2.1 · 1 row entry · 182 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk clientIfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-CLIENT-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-CLIENT-MIB::clientIfTable' 
The interface list.
clientIfEntry row .1.3.6.1.4.1.8708.2.27.2.2.1.1
An entry in the interface list.
Indexes
Column Syntax OID
clientIfIndex
An arbitrary index assigned to each entry.
Unsigned32r/w
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.1
clientIfName
The management name of the interface, for
example 'client:1:2:1', where the first number
indicates sub-rack, the second slot number and
the third is the port number.
Examples:

client:s:s:p - Generic clien…
LUM-TCMgmtNameStringr/w
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.2
clientIfDescr
User configurable label.

This attribute can be written via SNMP.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.3
clientIfSubrack
The number of the subrack where the interface
is located.
LUM-TCSubrackNumberr/w
Type Constraints:
range: 0..15
Description:
The number of a subrack within a network element.

0 signifies an undefined subrack number.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.4
clientIfSlot
The number of the slot where the interface is
located.
LUM-TCSlotNumberr/w
Type Constraints:
range: 0..22
Description:
The number of a slot within a subrack.

0 signifies an undefined slot number.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.5
clientIfTxPort
The number of the port where the TX-side of the
interface is located.
LUM-TCPortNumberr/w
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.6
clientIfRxPort
The number of the port where the RX-side of the
interface is located.
LUM-TCPortNumberr/w
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.7
clientIfInvPhysIndexOrZero
The row in the invPhysTable for this interface.
Set to 0 if not known.
Unsigned32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.8
clientIfEntityId
Index in entity table.

-- Only used for notifications
Unsigned32r/w
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.9
clientIfAdminStatus
The administrative state for the interface.

down - The interface is de-activated.

service - The interface is activated but alarms are
suppressed. Intended for use during service or
re-confi…
LUM-TCBoardOrInterfaceAdminStatusr/w
Type Values:
1down
2service
3up
Description:
The administrative state for a board or
interface.

down - The board/interface should be inactive.

service - The board/interface is activated but
alarms are suppressed. Intended for use during
servi…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.10
clientIfOperStatus
The operational state for the interface.

notPresent - The physical resources are not
available.

down - The interface is de-activated or there are
faults preventing its transition to the 'up…
LUM-TCBoardOrInterfaceOperStatus
Type Values:
1notPresent
2down
3up
Description:
The operational state for a board or interface.

notPresent - The board/interface is not available.

down - The board/interface is de-activated or
there are faults preventing it from going to the
'up…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.11
clientIfLaserStatus
The operational state of the laser.

off - The laser is turned off.

on - The laser is turned on.
Enumeration
Enumerated Values:
1off
2on
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.12
clientIfTxSignalStatus
The operational state for outgoing (TX) signal
of the interface.

down - A fault that would lead to a protection
switch has occurred.

degraded - The signal quality is impaired.
…
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.13
clientIfForwardAls
Forward Automatic Laser Shut-down. Decides if
laser shutdown of the client should occur when
a defect on the line or remote client is detected.

disabled - The laser is NOT turned off at defect
detection.
…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.14
clientIfSuppressRemoteAlarms
Suppress AIS in the alarm list.
The fault status on the port object can, however,
be seen.

disabled - alarms are not suppressed.

enabled - alarms are suppressed.
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.15
clientIfFarEndLoopback
Loop the client TX signal back to the client RX.
This is also called Terminal loopback.

disabled - the signal is not looped

enabled - the signal is looped.
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.16
clientIfFormat
The expected signal format.

The default value is board dependent. For information
about the default value for this particular board,
please refer to the user manual.
LUM-TCSignalFormatr/w
Type Values:
1other
2stm1
3stm4
4stm16
5gbE
6stm64
7fc1Gb
8fc2Gb
9wan10GbE
10unused
11lan10GbE
12escon
13esconLL
14dvb270
15oc3
16oc12
17oc48
18oc192
19hdtv1485
20ethernet
21fastEthernet
22lan10GbEFec
23wan10GbEStm64Fec
24fc4Gb
25etr
26auto
27down
28stm1Oc3
29stm4Oc12
30stm16Oc48
31stm64Oc192
32gbe9Line
34ddgbeLine
35gbEorTrm5500
36fc8Gb
37otu2
38otu2e
39e1
40t1
41mbh2Gb5
42syncE
43line4G
44mbh4Gbps
45fecLan10GbE1A
46fecLan10GbE1B
47sdi3G
48iWdm4G
49sdSdi270
50hdtvNTSC
51oc768
52stm256
53lan40GbE
54wan40GbE
55sfStm256Oc768
56iwdm40Gb
57otu4
58lan100GbE
59transpLan10GbE
60cpri1
61cpri2
62cpri3
63cpri4
64cpri5
65cpri6
66cpri7
67fc10Gb
68fc16Gb
69cpri8
70obsai1x
71obsai2x
72obsai4x
73obsai8x
74otu1
75iwdm11G
76rw100G
77rw200G
78otu4SdFec
79otuj1
80otuj2
81fc32Gb
82clearChannel32GbFc
83lan400GbE
84flexO4
85flexO2
86openZRplus400
87openZRplus200
88lan25GbE
89otuC2
90otuC4
91otuC1i
92otuC2i
93otuC1ix2
94otuC4i
95otuC1ix4
2147483647notApplicable
Description:
Signal format for an interfaces.

other - Unspecified format (see bitrate configuration
for speed)

stm1 - STM-1 SDH signal

stm4 - STM-4 SDH signal

stm16 - STM-16 SDH signal
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.17
clientIfGfpMode
Generic framing procedure mode
Enumerationr/w
Enumerated Values:
1transparent
2framed
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.18
clientIfBandWidth
Band-width in VC-3 or VC-4.

The parameter is interpreted as VC-3 or VC-4
depending on the traffic combination:

- VC-3 is used in framedGbEx10
- VC-4 is used in framedGbEx10Vc4
Integer32r/w
Constraints:
range: 0-48
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.19
clientIfRateLimit
Rate limit of link in 1,000,000 bits
(Mb) per second.

Zero (0) is a special value meaning that the
rate-limiting procedure is disabled.

The legal range is: 10...1000, in step of 1
Integer32r/w
Constraints:
range: 0-1000
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.20
clientIfAutoNegotiationMode
The wanted auto negotiation mode.

off - auto negotiation process is disabled

on - auto negotiation process is enabled
Enumerationr/w
Enumerated Values:
1off
2on
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.21
clientIfAutoNegotiationStatus
The result of the auto negotiation procedure

incomplete - the result is still pending

half - half duplex

full - full duplex
Enumeration
Enumerated Values:
1incomplete
2half
3full
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.22
clientIfDuplexCapability
The duplex capability of the HW.

half - supports half duplex

full - supports full duplex
Enumeration
Enumerated Values:
1half
2full
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.23
clientIfFlowControlMode
The mode for handling flow control between
the local device and link partner.

The PAUSE settings has the following meaning
when auto-negotiation is enabled.

Setting 802.3 equivalent
----…
Enumerationr/w
Enumerated Values:
1noPause
2rxPause
3txPause
4bothPause
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.24
clientIfInterPacketGap
Time between the frames in nano seconds.

Legal values are 64, 72, 80, ... 200, 320, 328,
336, ... 456
SNMPv2-SMIGauge32r/w
Constraints:
range: 64-456
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.25
clientIfFrameSize
The maximum size of the transmitted and
received frames (in bytes).
SNMPv2-SMIGauge32r/w
Constraints:
range: 1518-9600
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.26
clientIfTrxClass
String that describes the transceiver class.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.27
clientIfLaserBias
Measures laser bias current value in tenths of
mA (0.1 mA).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.28
clientIfPowerLevel
The received power level in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.29
clientIfReceiverSensitivity
The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.30
clientIfPowerLevelLowRelativeThreshold
The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity.
Integer32r/w
Constraints:
range: -50-200
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.31
clientIfLossOfSignal
Loss of signal.
Applicable for all signal formats.

A(ctivation): Active loss of signal HW
indication.

D(e-activation): Inactive loss of signal HW
indication.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.32
clientIfLossOfFrame
Loss of frame.
All forms of sync loss.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.33
clientIfBitrateMismatch
Bitrate mismatch (Other).
Applicable for other signal formats.

D: The interface is unable to lock to the
inserted signal.

D: The interface is able to lock to the
inserted signal.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.34
clientIfAuAlarmIndicationSignalW2C
Alarm indication signal (AIS) on the trunk-side.
Applicable for SDH/Sonet signal formats.

A: An 'all ones' SDH signal is detected.

D: SDH signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.35
clientIfTransmitterFailed
The transceiver HW has detected a failure
in the transmitter part.

A: The transmitter has failed

D: The transmitter is OK again
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.36
clientIfTrxCodeMismatch
The inserted transceiver does not have a legal
manufacturer code.

A: A transceiver with illegal code is inserted.

D: The transceiver with illegal code is removed.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.37
clientIfTrxBitrateUnavailable
The inserted transceiver does not support the
requested bit rate.

A: A transceiver with other supported bit rate than
the requested bit rate is inserted.

D: The transceiver with the non-…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.38
clientIfTrxMissing
An expected transceiver is missing.

A: An expected transceiver is missing.

D: The missing transceiver is inserted.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.39
clientIfReceivedPowerHigh
Received power level is too high.
Applicable for all signal formats.

A: The received power level exceeds the
the built-in overload threshold.

D: The received power level is 0.5 dB below the…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.40
clientIfReceivedPowerLow
Received power level low threshold exceeded.
Applicable for all signal formats.

A: The received power level is below the
associated threshold.

D: The received power level is 0.5 dB above th…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.41
clientIfLinkDown
A: Failure to negotiate a connection with the
other party.

D: A connection is negotiated.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.42
clientIfConfigurationCommand
Command to change the signal format, and, if
applicable, also the fec type and interleaver mode.
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.43
clientIfGbeUtilization
Shows the current bandwidth utilization
measured at the physical (802.3 PHY) layer.
The value represents a snapshot of the utilization
during the latest second. It is expressed in per cent (%)
of the nominal maximum ra…
Unsigned32
Constraints:
range: 0-1000
range: 2147483646-2147483646
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.44
clientIfLossOfSync
Loss of sync.
All forms of sync loss.

A: GbE 'frame' can not be located.

D: GbE 'frame' is located.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.45
clientIfConfigureTrxModeCommand
Command to change the TRX mode (client or line) and/or
TRX media (optical or electrical).
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.46
clientIfTrxMode
Shows if the port is configured as:

- normal CLIENT interface connected to a non XTM Series
client equipment, with non-colored, or colored TRXes.

- a LINE interface connected to other XTM…
Enumerationr/w
Enumerated Values:
1client
2line
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.47
clientIfExpectedTxFrequency
The expected frequency given in hundreds of GHz
(0.01 GHz).
LUM-TCLambdaFrequencyr/w
Type Values:
0undefined
1iWdmPonFrequency
2otclg
130b1300
150b1500
850w850
1270w1270
1290w1290
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1530w1530
1550w1550
1570w1570
1590w1590
1610w1610
1611w1611
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19135ch9135
19140ch914
19145ch9145
19150ch915
19155ch9155
19160ch916
19165ch9165
19170ch917
19175ch9175
19180ch918
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.48
clientIfTxFrequency
The transmitted frequency given in hundreds of
GHz (0.01 GHz).
LUM-TCLambdaFrequency
Type Values:
0undefined
1iWdmPonFrequency
2otclg
130b1300
150b1500
850w850
1270w1270
1290w1290
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1530w1530
1550w1550
1570w1570
1590w1590
1610w1610
1611w1611
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19135ch9135
19140ch914
19145ch9145
19150ch915
19155ch9155
19160ch916
19165ch9165
19170ch917
19175ch9175
19180ch918
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.49
clientIfUnexpectedTxFrequency
The actual frequency does not match the
pre-configured frequency.

A pre-configured frequency of '0' matches
all actual frequencies.

A: The configured frequency does not match the
actual fre…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.50
clientIfIllegalFrequency
The frequency supported by the transceiver is not
recognized by the system.

A: Invalid or unknown frequency information is
detected in the (pluggable) transceiver or
board production data.
…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.51
clientIfLaserForcedOn
When enabled, the laser is on regardless of whether
there is a trunc signal present or not.

disabled - the laser is only on when there is a
trunc signal.

enabled - the laser is …
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.52
clientIfTrxMedia
Defines the media and capability of the TRX.
LUM-TCTrxMediar/w
Type Values:
0undefined
1optical
2tp1000BaseT
3tp100BaseT
4tp10BaseT
5electrical
Description:
Defines the media and capability of the TRX

optical - Optical media

tp1000BaseT - Twisted-pair capable of 1000BaseT

tp100BaseT - Twisted-pair capable of 100BaseT

tp1…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.53
clientIfTrxMediaMismatch
The TRX media does not match the expected one.

A: Invalid or mismatching trx media is
detected.

D: The (pluggable) transceiver or board is
replaced, or the configuration is changed.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.54
clientIfTruncAutoNegotiationMode
Decides whether auto negotiation shall
be performed over the trunc connection.

This is applicable when the terminating
node at the other side of the
trunc is configured as follows:

- it h…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.55
clientIfObjectProperty
Property mask.
LUM-TCObjectProperty
Type Constraints:
range: 0..4294967295
Description:
A bitmask of length 32 encoding certain properties
of an object.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.56
clientIfTxPowerLevel
The transmitted power level in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.57
clientIfLaserTempActual
The actual laser temperature in units of
0.1 degrees centigrade.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.58
clientIfTraceIntrusionMode
Indicates whether the trace identifier should be
inserted into the transmitted signal or to be
transparent.

disabled - The trace identifier is taken from
the recevied signal if possible.

en…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.59
clientIfTraceTransmitted
The trace identifier to be transmitted from this
interface.

The identifier length is by default 0 to 15. For
mxp8iiSonet board the length i 0 to 62.

Set to empty string for default value:
…
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-62
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.60
clientIfTraceReceived
The received trace identifier for this interface.
SNMPv2-TCDisplayString
Constraints:
range: 0-62
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.61
clientIfTraceExpected
Trace identifier used for matching against
the received trace identifier.

The identifier length is by default 0 to 15. For
mxp8iiSonet board the length is 0 to 62.
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-62
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.62
clientIfTraceAlarmMode
Controls if the trace identifier mismatch alarm
should be raised.

disabled - The alarm is disabled.

enabled - The alarm is raised if expected trace
identifier differs from the received trac…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.63
clientIfTraceMismatch
Indicates if the expected trace identifier
differs from the received trace identifier.

A: The received trace identifier differs from
the expected trace identifier.

D: The identifiers match.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.64
clientIfNearEndLoopback
Loop the client RX signal back to the client TX.
This is also called Facility loopback

disabled - the signal is not looped

enabled - the signal is looped.
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.65
clientIfRxSignalStatus
The operational state for incoming (RX) signal
of the interface.

down - A major fault has occurred

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.66
clientIfMsAlarmIndicationSignalC2W
MS Alarm indication signal (MS-AIS) on the
client side.
Applicable for SDH/Sonet signal formats.

A: An 'all ones' pattern is detected.

D: The signal is recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.67
clientIfMsAlarmIndicationSignalW2C
MS Alarm indication signal (MS-AIS) on the trunc
side. Applicable for SDH/Sonet/IWDM signal formats.

A: An 'all ones' pattern is detected.

D: The signal is recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.68
clientIfRemoteDefectIndication
Remote defect indication.
Applicable for SDH/Sonet signal formats.

A: RDI indication (in SDH/Sonet frame) active.

D: RDI indication inactive.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.69
clientIfJ1TxTrailTrace
The J1 trail trace identifier(s) to be
transmitted for the VC4s/VC3s related to this
interface, in the line signal (STM16/OC48).

This parameter can be used in two different
modes, see j1TxTrailTraceInsert…
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-15
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.70
clientIfJ1TxTrailTraceInsertionMode
Controls how the J1 trail trace insertion
should work, i.e. how the j1TxTrailTrace
parameter shall be inserted in the line
signal.

Important: there is only one j1TxTrailTrace
per interface, while each int…
Enumerationr/w
Enumerated Values:
1vcGroupLevel
2individualVcLevel
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.71
clientIfTrxFailed
A transceiver hardware failure is detected.

A: The transceiver fails.

D: The transceiver is replaced.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.72
clientIfDisabled
The interface is disabled.

A: Interface disabled.

D: Interface enabled.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.73
clientIfLoopback
The interface is set in loopback mode.

A: Loopback enabled.

D: Loopback disabled.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.74
clientIfVcGroupFailedW2C
The received line signal contains a VC
mapped to this interface, that is
faulty, e.g. unequipped.

Please note that this fault is in the
LINE SIGNAL, but is presented at the client.

A: Some …
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.75
clientIfReadJ1
Read the received J1 for the VC4/VC3 in the
STM16 frame associated to this interface.

Synopsis: readJ1
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.76
clientIfClientSignalFailed
The received line signal contains a VC
mapped to this interface, that is
faulty, e.g. unequipped.

Please note that this fault is in the
LINE SIGNAL, but is presented at the client.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.77
clientIfAuLossOfPointer
Loss of pointer.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.78
clientIfGfpLossOfFrame
GFP Loss of frame.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.79
clientIfHighSpeed
The expected signal bit rate in units of
1,000,000 bits (Mb) per second. If this object
reports a value of 'n' then the speed of the
interface is somewhere in the range of 'n-500,000'
to 'n+499,999'. Board tpQMri has a …
SNMPv2-SMIGauge32r/w
Constraints:
range: 12500-491520
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.80
clientIfActualFormat
The actual signal format.
LUM-TCSignalFormat
Type Values:
1other
2stm1
3stm4
4stm16
5gbE
6stm64
7fc1Gb
8fc2Gb
9wan10GbE
10unused
11lan10GbE
12escon
13esconLL
14dvb270
15oc3
16oc12
17oc48
18oc192
19hdtv1485
20ethernet
21fastEthernet
22lan10GbEFec
23wan10GbEStm64Fec
24fc4Gb
25etr
26auto
27down
28stm1Oc3
29stm4Oc12
30stm16Oc48
31stm64Oc192
32gbe9Line
34ddgbeLine
35gbEorTrm5500
36fc8Gb
37otu2
38otu2e
39e1
40t1
41mbh2Gb5
42syncE
43line4G
44mbh4Gbps
45fecLan10GbE1A
46fecLan10GbE1B
47sdi3G
48iWdm4G
49sdSdi270
50hdtvNTSC
51oc768
52stm256
53lan40GbE
54wan40GbE
55sfStm256Oc768
56iwdm40Gb
57otu4
58lan100GbE
59transpLan10GbE
60cpri1
61cpri2
62cpri3
63cpri4
64cpri5
65cpri6
66cpri7
67fc10Gb
68fc16Gb
69cpri8
70obsai1x
71obsai2x
72obsai4x
73obsai8x
74otu1
75iwdm11G
76rw100G
77rw200G
78otu4SdFec
79otuj1
80otuj2
81fc32Gb
82clearChannel32GbFc
83lan400GbE
84flexO4
85flexO2
86openZRplus400
87openZRplus200
88lan25GbE
89otuC2
90otuC4
91otuC1i
92otuC2i
93otuC1ix2
94otuC4i
95otuC1ix4
2147483647notApplicable
Description:
Signal format for an interfaces.

other - Unspecified format (see bitrate configuration
for speed)

stm1 - STM-1 SDH signal

stm4 - STM-4 SDH signal

stm16 - STM-16 SDH signal
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.81
clientIfRdiIntrusionMode
Indicates whether RDI information should be
inserted in the transmitted signal.

disabled - No RDI information is inserted in the
transmitted signal.

enabled - RDI information is …
Enumeration
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.82
clientIfMuxQuadVc4
States which quadrant of the payload
that the interface is connected to
in rx direction. (outgoing line)
Unsigned32r/w
Constraints:
range: 1-4
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.83
clientIfDemuxQuadVc4
States whitch quadrant of the payload
that the interface is connected to
in tx direction. (outgoing client)
Unsigned32r/w
Constraints:
range: 1-4
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.84
clientIfCcConnectionMode
controls if DemuxPayloadQuad is same
as MuxPayloadQuad
(same => connected, not same => disconnected)
Enumerationr/w
Enumerated Values:
1connected
2disconnected
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.85
clientIfCcConfigurationCommand
Command to change the crossconnect,

If no arguments are given, the user will be prompted.
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.86
clientIfIllegalSignalFormat
IllegalSignalFormat.

A(ctivation): Actual Format does NOT match
expected Format.

D(e-activation): Actual Format does match
expected Format.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.87
clientIfSynchProtPortId
The Id for this port in the synch prot group,
to identify the port. (A or B)
Enumeration
Enumerated Values:
1portA
2portB
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.88
clientIfSynchProtGroupMemberPort
The port number for the TX side of the port
that is in this synch protection group.
LUM-TCPortNumber
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.89
clientIfSynchProtGroupStatus
Note: This object is deprecated.

The operational state for the protection group.

bothDown - both sides down

bothUp - both sides up

ADownBUp - left side down,…
Enumeration
Enumerated Values:
1bothDown
2bothUp
3portADownBUp
4portAUpBDown
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.90
clientIfSynchProtActivePort
The operational state for the protection group.

none - no side is active.

A - the A port is active.

B - the B port is active.
Enumeration
Enumerated Values:
1none
2portA
3portB
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.91
clientIfSynchProtPortStatus
The operational synch protection state
for this port in the synch protection group.

down - this port is out of service.

up - this port is active.
Enumeration
Enumerated Values:
1down
2up
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.92
clientIfSynchProtToggleActivePort
Command to toggle which port is active in the synch
prot group
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.93
clientIfNearEndLoopbackTimeout
Timeout for near end loopback (a.k.a. facility
loopback) to make sure connection to node is not
lost if ppp link is broken.
The unit is hours. 0.1 means 6 minutes.
Integer32r/w
Constraints:
range: 0-1200
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.94
clientIfNearEndLoopbackEnabled
Near end loopback (a.k.a. facility loopback)
is enabled.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.95
clientIfChangeNearEndLoopbackCommand
Command to change near end loopback (a.k.a.
facility loopback) and loopbacktimeout
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.96
clientIfFarEndLoopbackEnabled
Far end loopback (a.k.a. terminal loopback)
is enabled.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.97
clientIfFarEndLoopbackTimeout
Timeout for far end loopback (a.k.a. terminal
loopback) to make sure connection to node is
not lost if ppp link is broken.
The unit is hours. 0.1 means 6 minutes.
Integer32r/w
Constraints:
range: 0-1200
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.98
clientIfChangeFarEndLoopbackCommand
Command to change far end loopback (a.k.a.
terminal loopback) and loopbacktimeout
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.99
clientIfFormatNotSupportedByHw
The HW revision does not support
the selected signal format.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.100
clientIfLaserMode
The administrative state of the TX-side laser.

on - The laser is turned on.

als - Automatic Laser Shutdown/Turn-Off
when lossOfSignal is detected on the RX side.
Enumerationr/w
Enumerated Values:
1on
2als
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.101
clientIfAlarmIndicationSignalLineC2W
Alarm indication signal Line (AIS-L) on the
client side.
Applicable for Sonet signal formats.

A: An 'all ones' Sonet signal is detected.

D: Sonet signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.102
clientIfFarEndClientFailure
Failure on far end client.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.103
clientIfOHTransparency
The 'OH Transparency' setting shall be set to 'off'
for standard SDH/SONET mode. Does not work when
client wrapper is enabled.

When set to 'on', the following tributary OH-bytes
are transparently transpor…
Enumerationr/w
Enumerated Values:
1off
2on
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.104
clientIfConnectedLine
The line ports that this client port is connected to.
Unsigned32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.105
clientIfForwardingErrorCorrectionMode
The administrative state of the forwarding error
correction function.

disabled - FEC is disabled.

enabled - FEC is activated.

auto - autonegotiation is used to enable or disa…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
3auto
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.106
clientIfNoFrequencySet
The tunable laser frequency has not been set.

A: Tunable laser frequency is not set.

D: Tunable laser frequency is set.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.107
clientIfJitterAttenuatorBW
Determines the wander/jitter transfer bandwidth
of the wander/jitter attenuator.
With Option 1, the bandwidth is within 1 - 10 Hz,
and with Option 2, the bandwidth is below 0.1 Hz.

The values are defined …
Enumerationr/w
Enumerated Values:
0option1
1option2
2notUsed
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.108
clientIfConnectionStatus
Shows the name of the wdm port and
possible subchannel/vc4 that it is connected to
or Unconnected if not connected.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.109
clientIfLoopFilterUnlocked
The loopfilter is unlocked.
This is applicable for synchronous formats.

A: Loopfilter is unlocked

D: Loopfilter is locked
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.110
clientIfCableLength
The 'Cable length' is applicable for SONET mode
(T1).

The settings are for short haul (intra-building) T1
networks and will adjust the power of the
transmitted signal to compensate for the
attenuation…
Enumerationr/w
Enumerated Values:
0feet133
1feet266
2feet399
3feet533
4feet655
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.111
clientIfConnectedForeignIndex
Shows the index of the connected interface.
Or 0 if unconnected.
Unsigned32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.112
clientIfDisconnect
Disconnect existing crossConnections
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.113
clientIfOHTransparencyBitMask
The OH transparency bitmask.
Bits:
K1K2 = 0x01
E1E2 = 0x02
F1 = 0x04
D1-D3 = 0x08
D4-D12 = 0x10
B1 = 0x20
B2 = 0x40
E1 = 0x80
E2 = 0x100
J0 = 0x200
Unsigned32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.114
clientIfOHTransparencyString
OH transparency bytes tells if J0, rest
of RSOH/Section OH and/or MSOH/Line OH are
transparent or not.
When RSOH/Section OH is set to transparent the bytes
E1, F1, D1-D3 and B1 is transported tran-
sparent from client t…
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.115
clientIfOHTransparencySet
Set which bytes that should be OH transparent
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.116
clientIfAuAlarmIndicationSignalC2W
Alarm indication signal (AIS) on the
client-side.
Applicable for SDH/Sonet signal formats.

A: An 'all ones' SDH signal is detected.

D: SDH signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.117
clientIfAuLossOfPointerC2W
Loss of pointer detected on the client-side.
Applicable for SDH/Sonet signal formats.

A: A loss of pointer is detected.

D: SDH signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.118
clientIfAuLossOfPointerW2C
Loss of pointer detected on the line-side.
Applicable for SDH/Sonet signal formats.

A: A loss of pointer is detected.

D: SDH signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.119
clientIfEthStandbyIndicator
Shows if this port is in standby state.
Used with hub protection.
Enumeration
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.120
clientIfAuAlarmIndicationSignalW2CSonet
Alarm indication signal (AIS-P) on the line-side.

A: An 'all ones' Sonet signal is detected.

D: Sonet signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.121
clientIfAuAlarmIndicationSignalC2WSonet
Alarm indication signal (AIS-P) on the
client-side.

A: An 'all ones' Sonet signal is detected.

D: Sonet signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.122
clientIfAuLossOfPointerC2WSonet
Loss of pointer detected on the client-side.

A: A loss of pointer is detected.

D: Sonet signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.123
clientIfAuLossOfPointerW2CSonet
Loss of pointer detected on the line-side.

A: A loss of pointer is detected.

D: Sonet signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.124
clientIfTransceiverNoLoopback
The inserted transceiver does not support
the given loopback command.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.125
clientIfFecFailure
Too many errors to get valid FEC statistics. It is not
possible to run control loops based on FEC statistics.

A: Too many errors to get valid FEC statistics.

D: The FEC statistics is valid.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.126
clientIfLaneAlignmentError
Indicates whether multi-lane
BASE-R PCS (Physical Coding Sublayer)
has locked and aligned all received lanes.

A: PCS receive lanes not locked and aligned.

D: PCS receive lanes locked and al…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.127
clientIfFecCorrectedZeros
The number of corrected zeros.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.128
clientIfFecCorrectedOnes
The number of corrected ones.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.129
clientIfSignalDegraded
Too many error corrected.
If more errors are corrected
it might effect the client signal
in a negative way.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.130
clientIfFecType
Set FEC scheme.
disabled -- none specific FEC scheme is enabled.
gFec -- GFEC RS(255,239) FEC scheme,
according to ITU.T G.975
superFecI4 -- Super FEC I.4 FEC scheme,
according to ITU…
Enumerationr/w
Enumerated Values:
1disabled
2gFec
3superFecI4
4superFecI7
5sdFec
6uFec
7scFec
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.131
clientIfSignalDegradeThreshold
The alarm Signal Degraded shall be signalled
when BER reaches a limit.
The value will be affecting all ports.

Predefined BER levels
rxBerLevel1 = 1E-12
rxBerLevel2 = 1E-13
rxBerLevel3 = 1E-15
…
LUM-TCBerLevelMTOSIr/w
Type Values:
1qMargin1
2qMargin2
5osnrMargin1
10osnrMargin2
12rxBerLevel1
13rxBerLevel2
15rxBerLevel3
Description:
Predefined levels for signal degraded alarm

rxBerLevel1 = 1E-12
rxBerLevel2 = 1E-13
rxBerLevel3 = 1E-15

OSNRMargin1 = 0.5 dB margin with respect to FEC cliff
OSNRMargin2 = 1.0 dB margin with respec…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.132
clientIfExpectedOpticalLayerMapping
The expected optical layer mapping.
LUM-TCOpticalLayerMappingTyper/w
Type Values:
0undefined
1fourOpticalLanes
2tenOpticalLanes
3singleOpticalChannel
4eightOpticalLanes
Description:
Type of optical layer mapping.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.133
clientIfActualOpticalLayerMapping
The actual optical layer mapping.
LUM-TCOpticalLayerMappingType
Type Values:
0undefined
1fourOpticalLanes
2tenOpticalLanes
3singleOpticalChannel
4eightOpticalLanes
Description:
Type of optical layer mapping.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.134
clientIfConfigurationMismatch
The inserted transceiver does not support the
configuration of the optical layer mapping.

A: A transceiver with other supported optical layer
mapping than the requested mapping is inserted.
…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.135
clientIfChromaticDispersion
Received chromatic dispersion that describe the spreading of a light
pulse as it travels down a fiber when light pulses launched close together.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.136
clientIfDifferentialGroupDelay
The arrival time difference between two polarization states at
the output of the media (fiber).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.137
clientIfTxState
The operational state of the transiver for outgoing (TX) signal.
- Init started
- Init ready
- Data path locked
- Laser ready off
- Laser ready
- Laser bias ready
- Ready
- Low power
- High power up
- TX off
- TX turn on
LUM-TCTrxTxState
Type Values:
0missing
1initStarted
2initReady
3dataPathLocked
4laserReadyOff
5laserReady
6laserBiasReady
7ready
8lowPower
9highPowerUp
10txOff
11txTurnOn
2147483647notApplicable
Description:
TRX TX start-up sequence state.
- Init started
- Init ready
- Data path locked
- Laser ready off
- Laser ready
- Laser bias ready
- Ready
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.138
clientIfRxState
The operational state of the transiver for outgoing (RX) signal.
- Init started
- Init ready
- Frequency ready
- Input signal received
- A/D Converter ready
- Dispersion compensated
- Ready
- Low power
- Waiting for inp…
LUM-TCTrxRxState
Type Values:
0missing
1initStarted
2initReady
3frequencyReady
4inputSignalReceived
5adConverterReady
6dispersionCompensated
7ready
8lowPower
9waitingForInputSignal
2147483647notApplicable
Description:
TRX RX start-up sequence state.
- Init started
- Init ready
- Frequency ready
- Input signal received
- A/D Converter ready
- Dispersion compensated
- Ready
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.139
clientIfIdx
Internal object reference
Integer32r/w
Constraints:
range: -1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.140
clientIfIfNo
The physical interface number of the actual multi-connector port.
LUM-TCPortNumberr/w
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.141
clientIfIdxIf
Internal object reference of the actual multi-connector port.
Integer32r/w
Constraints:
range: -1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.142
clientIfUpPortId
Internal port reference for traffic unit.
Integer32
Constraints:
range: -1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.143
clientIfNoOfLanes
Number of lanes on port
Integer32r/w
Constraints:
range: -1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.144
clientIfFecCorrectedBits
FEC counter. Number of corrected bits
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.145
clientIfOSNRMargin
Optical signal-to-noise ratio margin (dB/0.1nm), based on calculation from rate of corrected bits.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.146
clientIfExpectedPhysicalLayerMapping
The expected physical layer mapping.
LUM-TCPhysicalLayerMappingTyper/w
Type Values:
1dualFiber
2singleFiber
Description:
Type of physical layer mapping.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.147
clientIfSignalDirection
Indicates the direction of the signal.

rx - Inbound direction

tx - Outbound direction

biDir - Bidirectional

txRx - Both Tx and Rx
LUM-TCSignalDirection
Type Values:
1rx
2tx
3biDir
4txRx
2147483646notAvailable
Description:
Indicates the direction of the signal.

rx - Inbound direction

tx - Outbound direction

biDir - Bidirectional

txRx - Both Tx and Rx
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.148
clientIfAid
The access identifier (AID) of the interface.
The format is according to GR-833.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.149
clientIfPhysicalLocation
The physical location of the if.
The format is according to GR-833.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.150
clientIfTrxCommunicationFailure
The board is unable to communicate with the transceiver.

alarm: Protocol errors detected on the transceiver control link.

ok: No communication errors detected on the transceiver control lin…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.151
clientIfTribPortId
Tributary port id.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.152
clientIfIfType
Type of interface (Individual or bundled).
LUM-TCInterfaceTyper/w
Type Values:
1individual
2bundled
3bundledSplit
2147483646notAvailable
2147483647notApplicable
Description:
Indicates the type of interface.

individual - The ports of the interface are handled individually

bundled - The ports of the interface are bundled

bundledSplit - The ports of the …
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.153
clientIfConfigurationCommandSNMP
Command to change the signal format, and, if
applicable, also the mode (framed, transparent) via SNMP.
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.154
clientIfTrxPowerOutOfRange
The power classification of the transceiver exceeds the design limit of the board.

alarm: A transceiver with a power classification that exceeds
the design limit of the board is inserted.
…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.155
clientIfTrxTunable
The transceiver is of tunable type.

true - Inserted TRX is of tunable type
false - Inserted TRX is not of tunable type
notAvailable - Attribute is not available under current circumst…
LUM-TCTruthValueWithNA
Type Values:
0true
1false
2147483646notAvailable
2147483647notApplicable
Description:
Defines a value that can be true, false or not available

true - The condition is false

false - The condition is not true

notAvailable (2147483646) is used when attribute is
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.156
clientIfAutoLambdaCapability
The Auto Lambda capability of the TRX.

none - Inserted TRX does not support auto lambda
notApplicable - Interface does not support auto lambda or TRX is not inserted
dualEndedPeer - TRX for du…
LUM-TCAutoLambdaCapability
Type Values:
0none
1notApplicable
2dualEndedPeer
3singleEndedTee
4singleEndedHee
Description:
Defines the auto lambda capability of the TRX

none - Inserted TRX does not support auto lambda
notApplicable - Interface does not support auto lambda or TRX is not inserted
dualEndedPeer - TRX for…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.157
clientIfAutoLambdaState
The Auto Lambda state of the TRX.

none - Inserted TRX does not support auto lambda
notApplicable - Interface does not support auto lambda or TRX is not inserted
searching - Searching auto …
LUM-TCAutoLambdaState
Type Values:
0none
1notApplicable
2searching
3locked
Description:
Defines the auto lambda state of the TRX

none - Inserted TRX does not support auto lambda
notApplicable - Interface does not support auto lambda or TRX is not inserted
searching - Searching au…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.158
clientIfTrxPowerCycleReset
When the attribute is set to reset the trx power cycle
is re-initialised, meaning the trx is cold started. Then the attribute is set to normal again
automatically.

Note: This function is only to be used a…
Enumerationr/w
Enumerated Values:
1normal
2reset
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.159
clientIfTrxAutoTuneFailure
The auto-tune process of an Auto-Lambda transceiver failed to establish the correct DWDM channel.
This alarm does not indicate a loss of signal. The optical signal is received but the tranceiver
failed to handshake the …
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.160
clientIfInterleaverMode
Defines the interleaver mode.

xtm - Legacy mode used in XTM family. Interleaver mode is disabled.

nonXtm - Must be used for interoperability with some other Infinera products, e.g. Groove/m…
LUM-TCInterleaverModer/w
Type Values:
0xtm
1nonXtm
Description:
Defines the interleaver mode
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.161
clientIfFecTypeUnavailable
Fec type unavailable.

The inserted transceiver does not support the
requested fec type.

alarm: A transceiver with other supported fec type
than the requested bit rate is inserted.
…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.162
clientIfTrxSignalFormatNotSupported
The signal format is not supported on this transceiver.

alarm: Signal format not supported.

ok: Signal format supported.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.163
clientIfLineCoding
Line coding.
qam16 - 16QAM
qpsk - QPSK
notApplicable - 2147483647 is used to indicate that the attribute
is not used on the board.
Enumerationr/w
Enumerated Values:
1qam16
3qpsk
2147483647notApplicable
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.164
clientIfServiceTopology
Service topology of the XR module.

p2p - XR module used in point to point mode.
p2mp - XR Module used in point to multipoint (break-out) mode.
LUM-TCModelOptionr/w
Type Values:
1p2p
2p2mp
Description:
Services using XR pluggables.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.165
clientIfPointToMultipointRole
Service role when XR modules used in point-to-multipoint (P2MP) mode.

hub - XR Hub role, should be able to serve up to 4 Leaf modules with 100G service each.
leaf - XR Leaf role, should be able to interco…
LUM-TCServiceRoler/w
Type Values:
1hub
2leaf
Description:
Service role.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.166
clientIfFiberMode
Type of physical layer mapping used with the XR module.

dualFiber - Dual fiber mode.
singleFiber - Single fiber mode.

Note! using single fiber with XR, the total capacity of the line is onl…
LUM-TCPhysicalLayerMappingTyper/w
Type Values:
1dualFiber
2singleFiber
Description:
Type of physical layer mapping.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.167
clientIfSingleFiberModeSide
Used sub-spectrum part in a single fiber mode.

a - Side A of the sub-spectrum is used.

b - Side B of the sub-spectrum is used.
LUM-TCSubspectrumr/w
Type Values:
1a
2b
2147483647notApplicable
Description:
Subspectrum parts.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.168
clientIfWantedTxPowerLevel
The wanted signal power level in units of 0.1 dBm.
Integer32r/w
Constraints:
range: -150-10
range: 2147483646-2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.169
clientIfMinSupportedTxPowerLevel
The minimum Tx signal power level the transceiver supports in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.170
clientIfMaxSupportedTxPowerLevel
The maximum Tx signal power level the transceiver supports in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.171
clientIfTxPowerLevelOutOfRange
Wanted Tx signal power level out of range.

alarm: The wanted signal power level is out of
transceiver's supported range.

ok: The wanted signal power level is within
transceiver's supported …
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.172
clientIfSignalInformation
Signal information.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.173
clientIfTrxModuleIdentifier
A unique identifier/name assigned to the module.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.174
clientIfLeafNetworkXC
Network cross connection port on the hub side when XR modules is used as leaf in point-to-multipoint (P2MP) mode.

hubPortId1 -- Hub-side host port 1 to connect the 100G service to.
hubPortId2 -- Hub-sid…
LUM-TCNetworkXcr/w
Type Values:
1hubPortId1
2hubPortId2
3hubPortId3
4hubPortId4
5hubPortId5
6hubPortId6
7hubPortId7
8hubPortId8
Description:
Cross connection port on hub side.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.175
clientIfCcAction
Connect or disconnect cross connections
Enumerationr/w
Enumerated Values:
1connect
2disconnect
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.176
clientIfVc4
The id of the vc4/STS3/STS1 within the STM16/OC192 frame.
Unsigned32r/w
Constraints:
range: 1-16
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.177
clientIfCcActionCommandSNMP
Command to connect or disconnect the crossconnect,
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.178
clientIfTxFrequencyFlex
The transmitted operating frequency.
In the CLI/GUI, the value is presented in unit of THz.
In SNMP the value is represented in unit of MHz.
LUM-TCFlexibleCenterFrequencyRangeWithNA
Type Constraints:
range: 0
range: 191350000..196100000
range: 2147483646..2147483647
Description:
Flexible center frequency range.
0 signifies an undefined flexible frequency
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.179
clientIfTrxXrTopologyMismatch
The configured service topology and/or service role do not match
with the actual topology/role in the module.

alarm: Configuration mismatch is detected.

ok: Configuraion matches or module i…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.180
clientIfEnhSopTolerance
Decides whether optical signals state of polarization (SOP)
tolerance mode shall be enabled or disabled.

disabled (1) - Enhanced SOP tolerance mode shall be disabled.
enabled (2) - Enhanced SOP tolerance…
LUM-TCEnableDisabler/w
Type Values:
1disabled
2enabled
Description:
Represents a boolean value.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.181
clientIfEnhSopToleranceStatus
Showing the actual status of optical signals
state of polarization (SOP) tolerance mode.

disabled (1) - Enhanced SOP tolerance mode is disabled.
enabled (2) - Enhanced SOP tolerance mode is enabled.
…
LUM-TCEnabledDisabledWithNA
Type Values:
1disabled
2enabled
2147483647notApplicable
Description:
disabled - Attribute is not set.

enabled - Attribute is set.

notApplicable (2147483647) is used when attribute is
not used in current configuration.
 .1.3.6.1.4.1.8708.2.27.2.2.1.1.182

clientVc4Table

table
.1.3.6.1.4.1.8708.2.27.2.3.1 · 1 row entry · 15 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk clientVc4Table
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-CLIENT-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-CLIENT-MIB::clientVc4Table' 
The interface list.
clientVc4Entry row .1.3.6.1.4.1.8708.2.27.2.3.1.1
An entry in the interface list.
Indexes
Column Syntax OID
clientVc4Index
An arbitrary index assigned to each if entry.
Unsigned32
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.1
clientVc4Name
The management name of the vc4,
e.g. vc4:1:2:1-2:8 where the first number
indicates sub-rack, the second slot number and
the third/forth are the port numbers. The last
number is the vc4 id within the STM16 frame.
LUM-TCMgmtNameString
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.2
clientVc4Descr
User configurable label.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.3
clientVc4Subrack
The number of the subrack where the vc4 is
located.
LUM-TCSubrackNumber
Type Constraints:
range: 0..15
Description:
The number of a subrack within a network element.

0 signifies an undefined subrack number.
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.4
clientVc4Slot
The number of the slot where the vc4 is
located.
LUM-TCSlotNumber
Type Constraints:
range: 0..22
Description:
The number of a slot within a subrack.

0 signifies an undefined slot number.
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.5
clientVc4TxPort
The number of the port where the TX-side of the
vc4 is located.
LUM-TCPortNumber
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.6
clientVc4RxPort
The number of the port where the RX-side of the
vc4 is located.
LUM-TCPortNumber
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.7
clientVc4Vc4
The id of the vc4/STS3/STS1 within the STM16/OC192 frame.
Unsigned32
Constraints:
range: 1-16
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.8
clientVc4ObjectProperty
Property mask.
LUM-TCObjectProperty
Type Constraints:
range: 0..4294967295
Description:
A bitmask of length 32 encoding certain properties
of an object.
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.9
clientVc4AuAlarmIndicationSignal
Alarm indication signal (AIS).
Applicable for SDH/Sonet signal formats.

A: An 'all ones' SDH/Sonet signal is detected.

D: SDH/Sonet signal recovered.
Enumeration
Enumerated Values:
1ok
2alarm
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.10
clientVc4AuLossOfPointer
Loss of pointer detected.
Applicable for SDH/Sonet signal formats.

A: A loss of pointer is detected.

D: SDH/Sonet signal recovered.
Enumeration
Enumerated Values:
1ok
2alarm
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.11
clientVc4RxSignalStatus
The operational state for incoming (RX) signal
of the interface.

down - A fault that would lead to a protection
switch has occurred.

degraded - The signal quality is impaired.
…
Enumeration
Enumerated Values:
1down
2degraded
3up
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.12
clientVc4ConcatenationStatus
Describes if and how the VC4s are concatenated.

on - Concatenation is used.

off - No concatenation is used.

can be vc3 (STS-1),
vc4 (STS-3, STM1/OC3),
vc4x4c (STS-12, STM4/OC…
Enumeration
Enumerated Values:
1on
2off
3vc3
4vc4
5vc4x4c
6vc4x16c
7vc4x64c
8sts1
9sts3c
10sts12c
11unknown
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.13
clientVc4PayloadStatus
Describes if the VC4/STS3 contains payload.

equipped - VC4/STS3 contains payload.

unequipped - No payload in VC4/STS3.
Enumeration
Enumerated Values:
1equipped
2unequipped
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.14
clientVc4ConnectionStatus
Shows the name of the client port and
possible subchannel/vc4 that it is connected to
or Unconnected if not connected.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.27.2.3.1.1.15

clientLanesTable

table
.1.3.6.1.4.1.8708.2.27.2.5.1 · 1 row entry · 25 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk clientLanesTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-CLIENT-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-CLIENT-MIB::clientLanesTable' 
The interface list.
clientLanesEntry row .1.3.6.1.4.1.8708.2.27.2.5.1.1
An entry in the interface list.
Indexes
Column Syntax OID
clientLanesIndex
An arbitrary index assigned to each if entry.
Unsigned32r/w
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.1
clientLanesName
The management name of the Lanes,
e.g. Lane:1:2:1:4 where the first number
indicates sub-rack, the second slot number and
the third is the interface number. The last
number is the lane id within the Client frame.
LUM-TCMgmtNameStringr/w
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.2
clientLanesSubrack
The number of the subrack where the lane is
located.
LUM-TCSubrackNumberr/w
Type Constraints:
range: 0..15
Description:
The number of a subrack within a network element.

0 signifies an undefined subrack number.
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.3
clientLanesSlot
The number of the slot where the lane is
located.
LUM-TCSlotNumberr/w
Type Constraints:
range: 0..22
Description:
The number of a slot within a subrack.

0 signifies an undefined slot number.
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.4
clientLanesTxPort
The number of the port where the TX-side of the
lane is located.
LUM-TCPortNumberr/w
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.5
clientLanesRxPort
The number of the port where the RX-side of the
lane is located.
LUM-TCPortNumberr/w
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.6
clientLanesLaneId
The id of the lane within the Client frame.
Unsigned32r/w
Constraints:
range: 1-16
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.7
clientLanesRxPowerLevel
The received power level in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.8
clientLanesWaveLength
The wavelength/frequency associated with the lane.
ch871 means the frequency 187.1 THz.
w1310 means the wavelength 1310 nm.

undefined if no wavelength is applicable.
LUM-TCLaneFrequency
Type Values:
0undefined
130b1300
150b1500
850w850
1270w1270
1290w1290
1297w1297
1301w1301
1305w1305
1309w1309
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1523w1523
1530w1530
1531w1531
1539w1539
1547w1547
1550w1550
1555w1555
1563w1563
1570w1570
1571w1571
1579w1579
1587w1587
1590w1590
1595w1595
1610w1610
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
2147483646notAvailable
2147483647notApplicable
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).

notApplicable - used to tell that attribute
is not used in current configuration.

notAvailable - used to tell that it is not
…
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.9
clientLanesBE
The counter associated with the number of
Bit Interleave Parity errors in a particular lane.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.10
clientLanesResetBE
Command to reset the BIP-8 error counter value.
Enumerationr/w
Enumerated Values:
1normal
2reset
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.11
clientLanesLossOfSignal
Loss of signal.
Applicable for all signal formats.

A(ctivation): Active loss of signal HW
indication.

D(e-activation): Inactive loss of signal HW
indication.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.12
clientLanesObjectProperty
Property mask.
LUM-TCObjectProperty
Type Constraints:
range: 0..4294967295
Description:
A bitmask of length 32 encoding certain properties
of an object.
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.13
clientLanesLossOfSync
Loss of sync.
All forms of sync loss.

A(ctivation): GbE 'frame' can not be located.

D(e-activation): GbE 'frame' is located.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.14
clientLanesLocalLinkFault
Local link fault. IEEE 802.3ah

A(ctivation): Active local link fault indication.

D(e-activation): Inactive local link fault indication.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.15
clientLanesRemoteLinkFault
Remote link fault. IEEE 802.3ah

A(ctivation): Active remote link fault indication.

D(e-activation): Inactive remote link fault indication.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.16
clientLanesHighBitErrorRate
High bit error rate (Hi-Ber). IEEE 802.3ah

A(ctivation): Active high bit error rate.

D(e-activation): Inactive high bit error rate.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.17
clientLanesReceiverSensitivity
The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.18
clientLanesReceivedPowerLow
Received power level low threshold exceeded.
Relative to the threshold in the port interface
table.
Applicable for all signal formats.

alarm: The received power level is below the
associated threshold.
…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.19
clientLanesIfNo
The physical interface number.
LUM-TCPortNumberr/w
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.20
clientLanesIdx
Internal object reference
Integer32r/w
Constraints:
range: -1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.21
clientLanesClientIfIdx
Internal object reference of the clientIf
Integer32r/w
Constraints:
range: -1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.22
clientLanesAdminStatus
The administrative state for the interface.

down - The interface is de-activated.

service - The interface is activated but alarms are
suppressed. Intended for use during service or
re-confi…
LUM-TCBoardOrInterfaceAdminStatusr/w
Type Values:
1down
2service
3up
Description:
The administrative state for a board or
interface.

down - The board/interface should be inactive.

service - The board/interface is activated but
alarms are suppressed. Intended for use during
servi…
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.23
clientLanesOperStatus
The operational state for the interface.

notPresent - The physical resources are not
available.

down - The interface is de-activated or there are
faults preventing its transition to the 'up…
LUM-TCBoardOrInterfaceOperStatus
Type Values:
1notPresent
2down
3up
Description:
The operational state for a board or interface.

notPresent - The board/interface is not available.

down - The board/interface is de-activated or
there are faults preventing it from going to the
'up…
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.24
clientLanesUpPortId
Internal port reference for traffic unit.
Integer32
Constraints:
range: -1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.5.1.1.25

clientMpoLanesTable

table
.1.3.6.1.4.1.8708.2.27.2.6.1 · 1 row entry · 17 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk clientMpoLanesTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-CLIENT-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-CLIENT-MIB::clientMpoLanesTable' 
The interface list.
clientMpoLanesEntry row .1.3.6.1.4.1.8708.2.27.2.6.1.1
An entry in the interface list.
Indexes
Column Syntax OID
clientMpoLanesIndex
An arbitrary index assigned to each if entry.
Unsigned32r/w
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.1
clientMpoLanesName
The management name of the Lanes,
e.g. Lane:1:2:1:4 where the first number
indicates sub-rack, the second slot number and
the third is the interface number. The last
number is the lane id.
LUM-TCMgmtNameStringr/w
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.2
clientMpoLanesSubrack
The number of the subrack where the lane is
located.
LUM-TCSubrackNumberr/w
Type Constraints:
range: 0..15
Description:
The number of a subrack within a network element.

0 signifies an undefined subrack number.
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.3
clientMpoLanesSlot
The number of the slot where the lane is
located.
LUM-TCSlotNumberr/w
Type Constraints:
range: 0..22
Description:
The number of a slot within a subrack.

0 signifies an undefined slot number.
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.4
clientMpoLanesIfNo
The physical interface number.
LUM-TCPortNumberr/w
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.5
clientMpoLanesLaneId
The identity of the lane within the Client frame.
Unsigned32r/w
Constraints:
range: 1-16
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.6
clientMpoLanesAdminStatus
The administrative state for the interface.

down - The interface is de-activated.

service - The interface is activated but alarms are
suppressed. Intended for use during service or
re-confi…
LUM-TCBoardOrInterfaceAdminStatusr/w
Type Values:
1down
2service
3up
Description:
The administrative state for a board or
interface.

down - The board/interface should be inactive.

service - The board/interface is activated but
alarms are suppressed. Intended for use during
servi…
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.7
clientMpoLanesOperStatus
The operational state for the interface.

notPresent - The physical resources are not
available.

down - The interface is de-activated or there are
faults preventing its transition to the 'up…
LUM-TCBoardOrInterfaceOperStatus
Type Values:
1notPresent
2down
3up
Description:
The operational state for a board or interface.

notPresent - The board/interface is not available.

down - The board/interface is de-activated or
there are faults preventing it from going to the
'up…
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.8
clientMpoLanesLaserStatus
The operational state of the laser.

off - The laser is turned off.

on - The laser is turned on.
LUM-TCOnOff
Type Values:
1off
2on
2147483646notAvailable
2147483647notApplicable
Description:
The configured laser mode.
notApplicable - used to tell that attribute
is not used in current configuration.
notAvailable - used to tell that it is not
possible to read attribute at the moment.
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.9
clientMpoLanesRxSensitivity
The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.10
clientMpoLanesRxPowerLevel
The received power level in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.11
clientMpoLanesPowerLevelLowRelativeThreshold
The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity.
Integer32r/w
Constraints:
range: -50-200
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.12
clientMpoLanesWaveLength
The wavelength/frequency associated with the lane.
ch871 means the frequency 187.1 THz.
w1310 means the wavelength 1310 nm.

undefined if no wavelength is applicable.
LUM-TCLaneFrequency
Type Values:
0undefined
130b1300
150b1500
850w850
1270w1270
1290w1290
1297w1297
1301w1301
1305w1305
1309w1309
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1523w1523
1530w1530
1531w1531
1539w1539
1547w1547
1550w1550
1555w1555
1563w1563
1570w1570
1571w1571
1579w1579
1587w1587
1590w1590
1595w1595
1610w1610
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
2147483646notAvailable
2147483647notApplicable
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).

notApplicable - used to tell that attribute
is not used in current configuration.

notAvailable - used to tell that it is not
…
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.13
clientMpoLanesObjectProperty
Property mask.
LUM-TCObjectProperty
Type Constraints:
range: 0..4294967295
Description:
A bitmask of length 32 encoding certain properties
of an object.
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.14
clientMpoLanesForwardAls
Forward Automatic Laser Shut-down. Decides if
laser shutdown of the client should occur when
a defect on the line or remote client is detected.

disabled - The laser is NOT turned off at defect
detection.
…
LUM-TCEnableDisabler/w
Type Values:
1disabled
2enabled
Description:
Represents a boolean value.
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.15
clientMpoLanesLossOfSignal
Loss of signal.
Applicable for all signal formats.

A(ctivation): Active loss of signal HW
indication.

D(e-activation): Inactive loss of signal HW
indication.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.16
clientMpoLanesRxPowerLow
Received power level low threshold exceeded.
Relative to the threshold in the port interface
table.
Applicable for all signal formats.

alarm: The received power level is below the
associated threshold.
…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.27.2.6.1.1.17