IPADv2-MIB Table View

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.2.1.1.1

ipadServiceifIndex

The MIB-II ifIndex for this service.

Enumerationr/w

Enumerated Values:

0	disabled
1	supervisor
2	network1
3	network2
4	user1
5	user2
6	ethernet
7	auxiliary
8	network3
9	atmCES
10	modem
100	virtual

.1.3.6.1.4.1.321.100.1.2.1.1.2

ipadServiceType

The type of this service.

Enumerationr/w

Enumerated Values:

1	other
2	tdm
3	ppp
4	pppMonitor
5	frameRelay
6	frameRelayMonitor
7	ip
8	serial
9	tty
10	scada
11	parallelIO
12	atm
13	hdlcPPP
14	atmCES
15	modem

.1.3.6.1.4.1.321.100.1.2.1.1.3

ipadServicePair

An entry in this table, which establishes a service pairing.

ipadChannelifIndex ipadChannelIndex

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.2.1.1.4

ipadServiceStatus

This parameter indicates the status of the service.
idle - The service is not doing anything or has not been configured for use.
down - The physical layer for the service is not ready.
training - The physical layer is n…

Enumeration

Enumerated Values:

1	other
2	idle
3	down
4	physicalUp
5	protocolUp
6	dead
7	changed
8	training
9	connecting

.1.3.6.1.4.1.321.100.1.2.1.1.5

ipadChannelTable

table

.1.3.6.1.4.1.321.100.1.3.1 · 1 row entry · 6 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadChannelTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadChannelTable'

The ipad channel table.

ipadChannelTableEntry row .1.3.6.1.4.1.321.100.1.3.1.1

An entry in the ipad channel table.

Indexes

Column Syntax OID

ipadChannelifIndex

Primary index into ipad channel table, MIB-II ifIndex.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.3.1.1.1

ipadChannelIndex

Channel index for the physical interface.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.3.1.1.2

ipadChannelService

Index into service table for this channel.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.3.1.1.3

ipadChannelPair

Pair for this channel; an entry in the channel
table. Use service pair in service table to
determine which service contains this channel.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.3.1.1.4

ipadChannelRate

Rate for this channel.

Enumerationr/w

Enumerated Values:

1	other
2	rate56
3	rate64
4	rate8

.1.3.6.1.4.1.321.100.1.3.1.1.5

ipadChannelIdlePattern

Idle pattern for this channel.

ipadDLCIservice ipadDLCInumber

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.3.1.1.6

ipadDLCITable

table

.1.3.6.1.4.1.321.100.1.4.1 · 1 row entry · 41 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadDLCITable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadDLCITable'

The ipad DLCI table.

ipadDLCITableEntry row .1.3.6.1.4.1.321.100.1.4.1.1

An entry in the ipad DLCI table.

Indexes

Column Syntax OID

ipadDLCIservice

An index into the ipad service table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.1

ipadDLCInumber

The DLCI number for this entry.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.2

ipadDLCIactive

Specifies if the DLCI is active.

Enumeration

Enumerated Values:

1	other
2	no
3	yes
4	pending

.1.3.6.1.4.1.321.100.1.4.1.1.3

ipadDLCIcongestion

Specifies if the dlci is receiving frames
with FECN or BECN bit set.

Enumeration

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.4.1.1.4

ipadDLCIremote

Remote DLCI number.

ipadDLCIremoteEquipActive

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.5

ipadDLCIremoteUnit

Name of the remote DLCI.

OctetString

Constraints:
range: 0-11

.1.3.6.1.4.1.321.100.1.4.1.1.6

Reports if the equipment attached to the
remote unit is active.

Enumeration

Enumerated Values:

1	other
2	inactive
3	active
4	sosAlarm

.1.3.6.1.4.1.321.100.1.4.1.1.7

ipadDLCIencapsulation

Type of protocol encapsulation used on this DLCI.

Enumerationr/w

Enumerated Values:

1	other
2	rfc1490
3	proprietary
4	rfc1490withEncryption
5	rfc1490withCompression

.1.3.6.1.4.1.321.100.1.4.1.1.8

ipadDLCIproprietary

When the encapsulation is proprietary, the traffic type must be
configured to gather protocol specific statistics.

Enumerationr/w

Enumerated Values:

1	other
2	ip
3	ipx
4	ethertype
5	none

.1.3.6.1.4.1.321.100.1.4.1.1.9

ipadDLCIpropOffset

When the encapsulation is proprietary, this is the number of bytes
after the frame relay header to look for the specified protocol
decode.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.10

ipadDLCIinBand

Determines if frames on this DLCI will be parsed to look
for management frames destined for the unit itself.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.4.1.1.11

ipadDLCICIR

Default committed information rate in bits per second.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.12

ipadDLCIBe

Default excess burst rate in bits per second.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.13

ipadDLCIminBC

If the corresponding interface is configured to enable
congestion management, the minimum transfer rate at which
the unit will throttle back offering data to the network.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.14

ipadDLCIrxMon

Determines if the SLA parameters will be monitored for received
frames.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.4.1.1.15

ipadDLCIdEctrl

Determines if the Rx monitor will set the DE bit on all frames
received in excess of the CIR before they are switched to their
destination port.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.4.1.1.16

ipadDLCIenableDelay

Enable or disable delay.

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	enable

.1.3.6.1.4.1.321.100.1.4.1.1.17

ipadDLCItxExCIRThreshold

Sets the Tx over CIR alarm threshold. This threshold
is the number of bits per second in excess of CIR. Setting
this field to 0 disables the alarm.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.18

ipadDLCItxExCIRAlarm

Reports if the Tx over CIR threshold has been exceeded.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.4.1.1.19

ipadDLCItxExBeThreshold

Sets the Tx over Be alarm threshold. This threshold is the
number of bits per second in excess of Be. Setting this
field to 0 disables the alarm.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.20

ipadDLCItxExBeAlarm

Reports if the Tx over Be threshold has been exceeded.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.4.1.1.21

ipadDLCIrxCongThreshold

Sets the Rx congestion alarm threshold. This threshold
is the number of frames received with BECN/FECN. Setting
this field to 0 disables the alarm.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.22

ipadDLCIrxCongAlarm

Reports if the Rx congestion threshold has been exceeded.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.4.1.1.23

ipadDLCIrxBECNinCIR

Reports if BECN has been received within CIR.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	alarmCondition

.1.3.6.1.4.1.321.100.1.4.1.1.24

ipadDLCIUASThreshold

Sets the UAS (unavailable seconds) alarm threshold. This
threshold is the number of seconds passed that the DLCI is
unavailable. Setting this field to 0 disables the alarm.

ipadDLCIRoundTripDelaySize

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.25

ipadDLCIUASAlarm

Reports if the UAS threshold has been exceeded.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.4.1.1.26

ipadDLCIAlarmReset

This is used to clear the current alarm counts.

Enumerationr/w

Enumerated Values:

1	dlciAlarmResetOther
2	dlciAlarmResetClearAlarms
3	dlciAlarmResetClearStats

.1.3.6.1.4.1.321.100.1.4.1.1.27

Specifies the packet size in octets used to calculate
round trip delay.

Integer32r/w

Constraints:
range: 16-1500

.1.3.6.1.4.1.321.100.1.4.1.1.28

ipadDLCIRoundTripDelayRate

Specifies the packet rate in seconds used to calculate
round trip delay.

Integer32r/w

Constraints:
range: 1-900

.1.3.6.1.4.1.321.100.1.4.1.1.29

ipadDLCIRemoteFramesOfferedWithinCIR

Count of frames sent within CIR from the remote end of the DLCI.

ipadDLCIRemoteFramesOfferedWithinBE

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.30

Count of frames sent within BE, but over CIR, from the remote end of the DLCI.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.31

ipadDLCIFramesReceived

Count of frames received by the local device on this DLCI.

ipadDLCIRemoteDataOfferedWithinCIR

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.32

Count of data octets sent within CIR from the remote end of the DLCI.

ipadDLCIRemoteDataOfferedWithinBE

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.33

Count of data octets sent within BE, but over CIR, from the remote
end of the DLCI.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.34

ipadDLCIDataReceived

Count of data octets received by the local device on this DLCI.

ipadDLCICompressionStatus

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.35

ipadDLCIRemoteIPAddress

The IP Address of the device on the remote end of this DLCI. This information
is only valid when the remote device supports Verilink's proprietary message
exchange.

SNMPv2-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.321.100.1.4.1.1.36

This is the current status of the compression engine for this DLCI.
disabled(2) indicates that the compression engine is disabled.
enabledAndNegotiated(3) indicates that compression is enabled, and has
been successfu…

Enumeration

Enumerated Values:

1	other
2	disabled
3	enabledAndNegotiated
4	enabledButNotNegotiated

.1.3.6.1.4.1.321.100.1.4.1.1.37

ipadDLCICompressionTxOctetsIn

This is a rolling counter of the number of octets given to the compression
engine.

ipadDLCICompressionTxOctetsOut

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.38

This is a rolling counter of the number of octets output from the compression
engine.

ipadDLCICompressionRxOctetsIn

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.39

This is a rolling counter of the number of octets given to the compression
engine.

ipadDLCICompressionRxOctetsOut

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.40

This is a rolling counter of the number of octets given to the compression
engine.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.4.1.1.41

ipadEndpointTable

table

.1.3.6.1.4.1.321.100.1.5.1 · 1 row entry · 10 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadEndpointTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadEndpointTable'

The ipad endpoint table.

ipadEndpointTableEntry row .1.3.6.1.4.1.321.100.1.5.1.1

An entry in the ipad endpoint table.

Indexes

ipadEndpointIndex

Column Syntax OID

ipadEndpointIndex

The index into the ipad endpoint table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.5.1.1.1

ipadEndpointName

The name for the endpoint.

OctetStringr/w

Constraints:
range: 0-11

.1.3.6.1.4.1.321.100.1.5.1.1.2

ipadEndpointService

An index into the ipad service table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.5.1.1.3

ipadEndpointDLCInumber

Data link connection identifier for this endpoint;
The DLCI number for this entry.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.5.1.1.4

ipadEndpointType

Endpoint type.

Enumerationr/w

Enumerated Values:

1	other
2	frLocal
3	frSwitched
4	ipRoute

.1.3.6.1.4.1.321.100.1.5.1.1.5

ipadEndpointForward

Index into the endpoint names table. This is the endpoint
on which data should be forwarded for switched endpoints.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.5.1.1.6

ipadEndpointBackup

Index into the endpoint table. This is the endpoint
on which data should be forwarded in the case where the
endpoint becomes inactive.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.5.1.1.7

ipadEndpointRefSLP

Index into the endpoint table. The service level parameters
can be copied from another configured endpoint.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.5.1.1.8

ipadEndpointRemoteIpAddr

IP address for remote.

Type Constraints:
range: 4

.1.3.6.1.4.1.321.100.1.5.1.1.9

ipadEndpointRemoteIpMask

IP address mask for remote.

Type Constraints:
range: 4

.1.3.6.1.4.1.321.100.1.5.1.1.10

ipadUserTable

table

.1.3.6.1.4.1.321.100.1.6.1 · 1 row entry · 15 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadUserTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadUserTable'

Table of user selected parameters.

ipadUserTableEntry row .1.3.6.1.4.1.321.100.1.6.1.1

An entry in the ipad user table.

Indexes

ipadUserIndex

Column Syntax OID

ipadUserIndex

Index into the ipad user table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.6.1.1.1

ipadUserFilterByDLCI

Enables Service+DLCI filtering for this user statistic.

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.321.100.1.6.1.1.2

ipadUserService

Specifies the service for this user type; identifies an entry in the
ipad DLCI table when combined with ipadUserDLCI. Meaningful when
ipadUserFilterByDLCI is enabled. Meaningless when collecting
PPP statistics.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.6.1.1.3

ipadUserDLCI

Specifies the DLCI for this user type; identifies an entry in the
ipad DLCI table when combined with ipadUserService. Meaningful when
ipadUserFilterByDLCI is enabled. Meaningless when collecting
PPP statistics.

ipadUserFilterByIPAddress

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.6.1.1.4

Enables IP address filtering for this user statistic. A
packet is counted towards the user statistics if the
result of a bitwise-and of an IP address in a transmitted
packet with ipadUserIPMask equals ipadUserIPAddress.

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.321.100.1.6.1.1.5

ipadUserIPAddress

Specifies the IP address for this user type.

Type Constraints:
range: 4

.1.3.6.1.4.1.321.100.1.6.1.1.6

ipadUserIPMask

Specifies the IP address mask for this user type.

Type Constraints:
range: 4

.1.3.6.1.4.1.321.100.1.6.1.1.7

ipadUserFilterByIPPort

Enables IP Port filtering for this user statistic.

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.321.100.1.6.1.1.8

ipadUserIPPort

Specifies the IP port for this user type.

Enumerationr/w

Enumerated Values:

5	rje
7	echo
11	systat
17	qotd
20	ftpdata
21	ftp
23	telnet
25	smtp
31	msgauth
37	time
42	nameserver
53	domain
66	sqlnet
69	tftp
70	gopher
79	finger
80	http
88	kerberos
92	npp
101	hostname
107	rtelnet
109	pop2
110	pop3
111	sunrpc
113	auth
119	nntp
137	netbiosns
138	netbiosdgm
139	netbiosssn
153	sgmp
161	snmp
162	snmptrap
163	cmipman
164	cmipagent
169	send
179	bgp
194	irc
201	atrtmp
202	atnbp
204	atecho
206	atzis
213	ipx
395	netcp
396	netwareip
444	snpp
494	povray
533	netwall
540	uucp
541	uucprlogin
600	ipcserver
749	kerberosadm

.1.3.6.1.4.1.321.100.1.6.1.1.9

ipadUserTxAlmThreshold

Sets the tx throughput alarm threshold in
bits per second. Setting this field to 0
disables the alarm.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.6.1.1.10

ipadUserTxAlmAlarm

Reports if the tx throughput threshold has been exceeded.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.6.1.1.11

ipadUserAlarmReset

This is used to clear the current alarm counts.

Enumerationr/w

Enumerated Values:

1	userAlarmResetOther
2	userAlarmResetClearAlarms
3	userAlarmResetClearStats

.1.3.6.1.4.1.321.100.1.6.1.1.12

ipadUserVpi

Specifies the Vpi for this user type; identifies a VC when combined
with the ipadUserService and ipadUserVci objects. Meaningful when
ipadUserFilterByVpiVci is enabled. Meaningless when collecting
PPP or Frame Relay …

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.6.1.1.13

ipadUserVci

Specifies the Vci for this user type; identifies a VC when combined
with the ipadUserService and ipadUserVpi objects. Meaningful when
ipadUserFilterByVpiVci is enabled. Meaningless when collecting
PPP or Frame Relay …

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.6.1.1.14

ipadUserFilterByVpiVci

Enables Vpi/Vci filtering for this user statistic. A
packet is counted towards the user statistics if the packet
is transmitted on the service/Vpi/Vci combindation specified by
ipadUserService, ipadUserVpi, and ipadUse…

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.321.100.1.6.1.1.15

ipadPPPCfgTable

table

.1.3.6.1.4.1.321.100.1.7.1 · 1 row entry · 28 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadPPPCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadPPPCfgTable'

The ipad PPP configuration table.

ipadPPPCfgTableEntry row .1.3.6.1.4.1.321.100.1.7.1.1

An entry in the ipad PPP configuration table.

Indexes

ipadPPPCfgService

Column Syntax OID

ipadPPPCfgService

The index into the PPP configuration table;
an entry in the ipad service table.

ipadPPPCfgInactivityTimer

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.7.1.1.1

ipadPPPCfgDialMode

Determines the permancency of a communications connection.

Enumerationr/w

Enumerated Values:

1	other
2	direct
3	dialup
4	demanddial

.1.3.6.1.4.1.321.100.1.7.1.1.2

Determines when a dial-up or demand-dial connection will be
disconnected due to inactivity in both directions. When this
parameter is set to zero then the timer is disabled.

ipadPPPCfgNegotiationInit

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.7.1.1.3

Determines if the port waits for the other end to initiate
parameter negotiations.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.4

ipadPPPCfgMRU

The maximum receive unit the interface will accept. Valid values
are in the range 128 - 4096, default is 1500.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.7.1.1.5

ipadPPPCfgACCM

Sets the async control character map used when generating
async HDLC frames. Setting a bit in the map causes the
corresponding character to be mapped for transparency.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.7.1.1.6

ipadPPPCfgNegMRU

Determines if MRU size is negotiated.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.7

ipadPPPCfgNegACCM

Determines if ACCM is negotiated.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.8

ipadPPPCfgNegMagic

Determines if the magic number is negotiated.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.9

ipadPPPCfgNegCompression

Determines if the PPP protocol header compression is negotiated.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.10

ipadPPPCfgNegAddress

Determines if the PPP HDLC header compression is negotiated.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.11

ipadPPPCfgNegPAP

Determines if PAP is negotiated with the peer when a more secure
authentication protocol is rejected.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.12

ipadPPPCfgNegCHAP

Determines if CHAP is negotiated with the peer when a more secure
authentication protocol is rejected.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.13

ipadPPPCfgAllowPAP

Determines if PAP is allowed to be negotiated by the peer.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.14

ipadPPPCfgAllowCHAP

Determines if CHAP is allowed to be negotiated by the peer.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.15

ipadPPPCfgPAPUsername

Identification string to determine the user identity.

OctetStringr/w

Constraints:
range: 0-30

.1.3.6.1.4.1.321.100.1.7.1.1.16

ipadPPPCfgPAPPassword

Password string to validate the user identity.

OctetStringr/w

Constraints:
range: 0-30

.1.3.6.1.4.1.321.100.1.7.1.1.17

ipadPPPCfgCHAPUsername

Identification string to determine the user identity.

OctetStringr/w

Constraints:
range: 0-30

.1.3.6.1.4.1.321.100.1.7.1.1.18

ipadPPPCfgCHAPSecret

Password string to validate the user identity.

OctetStringr/w

Constraints:
range: 0-30

.1.3.6.1.4.1.321.100.1.7.1.1.19

ipadPPPCfgPortIpAddress

Sets the IP address of the unit's port.

Type Constraints:
range: 4

.1.3.6.1.4.1.321.100.1.7.1.1.20

ipadPPPCfgPeerIpAddress

Sets the IP address of the unit's peer.

ipadPPPCfgNegIPCPCompression

Type Constraints:
range: 4

.1.3.6.1.4.1.321.100.1.7.1.1.21

ipadPPPCfgNegIpAddress

Determines if IP addresses are dynamically negotiated.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.22

Determines if Van Jacobson TCPIP header compression is negotiated.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.23

ipadPPPCfgSubnetMask

Specifies the subnet mask.

ipadPPPCfgAuthChallengeInterval

Type Constraints:
range: 4

.1.3.6.1.4.1.321.100.1.7.1.1.24

Specifies the authentication challenge interval.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.7.1.1.25

ipadPPPCfgEndpoint

Endpoint name to run PPP over another protocol.

OctetStringr/w

Constraints:
range: 0-11

.1.3.6.1.4.1.321.100.1.7.1.1.26

ipadPPPCfgNegIpMask

Determines if the subnet Mask is negotiated.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.27

ipadPPPCfgNegDNSAddress

Determines if the DNS address is negotiated.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.7.1.1.28

ipadPPPPAPTable

table

.1.3.6.1.4.1.321.100.1.7.2 · 1 row entry · 3 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadPPPPAPTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadPPPPAPTable'

Table of PAP authentication parameters.

ipadPPPPAPTableEntry row .1.3.6.1.4.1.321.100.1.7.2.1

An entry in the ipad PPP PAP table.

Indexes

ipadPPPPAPTableIndex

Column	Syntax	OID
ipadPPPPAPTableIndex The index into the PPP PAP association table.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.7.2.1.1`
ipadPPPPAPTableUsername Identification string to identify the user.	OctetStringr/w Constraints: `range: 0-30`	`.1.3.6.1.4.1.321.100.1.7.2.1.2`
ipadPPPPAPTablePassword Password string to validate the user identity.	OctetStringr/w Constraints: `range: 0-30`	`.1.3.6.1.4.1.321.100.1.7.2.1.3`

ipadPPPCHAPTable

table

.1.3.6.1.4.1.321.100.1.7.3 · 1 row entry · 3 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadPPPCHAPTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadPPPCHAPTable'

Table of CHAP authentication parameters.

ipadPPPCHAPTableEntry row .1.3.6.1.4.1.321.100.1.7.3.1

An entry in the ipad PPP CHAP table.

Indexes

ipadPPPCHAPTableIndex

Column	Syntax	OID
ipadPPPCHAPTableIndex The index into the PPP CHAP association table.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.7.3.1.1`
ipadPPPCHAPTableUsername Identification string to identify the user.	OctetStringr/w Constraints: `range: 0-30`	`.1.3.6.1.4.1.321.100.1.7.3.1.2`
ipadPPPCHAPTableSecret Password string to validate the user identity.	OctetStringr/w Constraints: `range: 0-30`	`.1.3.6.1.4.1.321.100.1.7.3.1.3`

ipadModemDialTable

table

.1.3.6.1.4.1.321.100.1.8.1 · 1 row entry · 18 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadModemDialTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadModemDialTable'

Table of modem dialing parameters.

ipadModemDialTableEntry row .1.3.6.1.4.1.321.100.1.8.1.1

An entry in the ipad modem dialing parameters table.

Indexes

ipadModemDialTableIndex

Column Syntax OID

ipadModemDialTableIndex

The index into the ipad modem dialing parameters table.
Equivalent to MIB-II ifIndex.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.1.1.1

ipadModemDialDataIndex

An index into the Modem Data Table, which selects a modem.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.1.1.2

ipadModemDialNumber

Specifies the telephone number to dial.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.1.1.3

ipadModemDialAbortTimer

Aborts a connection attempt if a dial-up connection has failed to connect within the specified number of seconds.
Range is 1..255.

ipadModemDialRedialAttempts

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.1.1.4

Determines how many attempts to initiate a dial-up connection after the initial failure.
Range is 0..10.

ipadModemDialDelayBeforeRedial

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.1.1.5

Specifies the number of seconds to wait before redialing.
Range is 1..255.

ipadModemDialChallengeScript

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.1.1.6

ipadModemDialLoginScript

Script string interpreted after an originated dial-up connection is first established.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.1.1.7

ipadModemDialUsername

Identification string to determine the user identity.

OctetStringr/w

Constraints:
range: 0-30

.1.3.6.1.4.1.321.100.1.8.1.1.8

ipadModemDialPassword

Password string to validate the user identity.

OctetStringr/w

Constraints:
range: 0-30

.1.3.6.1.4.1.321.100.1.8.1.1.9

Script string interpreted after an answered dial-up connection is first established.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.1.1.10

ipadModemDialAnswerRings

Answers an incoming call on the given number of rings.
A value of zero disables answering.
Range is 0..255.

ipadModemDialCallbackRedialDelay

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.1.1.11

ipadModemDialCommand

The set values perform the following actions:
setupNow - Execute the modem setup scripts
dialNow - Initiate dialing procedures
answerNow - Initiate answering procedures
disconnectNow - Initiate disconnect procedures

Enumerationr/w

Enumerated Values:

1	other
2	setupNow
3	dialNow
4	answerNow
5	disconnectNow

.1.3.6.1.4.1.321.100.1.8.1.1.12

ipadModemDialStatus

This object reports the current activity of the modem control feature

disabled - The feature is not enabled
setup - The feature is configuring the modem
error - The feature could not setup the modem
idle …

Enumeration

Enumerated Values:

1	other
2	disabled
3	idle
4	dialing
5	answering
6	negotiating
7	online
8	disconnecting
9	error
10	setup
11	awaitingCallback
12	dialWait
13	ringing

.1.3.6.1.4.1.321.100.1.8.1.1.13

ipadModemDialSecurity

disable - Dial-up security not enabled
password - Challenge/Login password scripts used
callback - Password security followed by answerer calling back
callbackVerify - Callback and verify using the callback challenge/re…

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	password
4	callback
5	callbackVerify

.1.3.6.1.4.1.321.100.1.8.1.1.14

Specifies the number of seconds to wait before redialing.
Range is 1..255.

ipadModemDialCallbackTimeout

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.1.1.15

This object sets the number of seconds to wait for a security callback before failing the connection attempt.

ipadModemDialCallbackChalScript

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.1.1.16

Callback security challenge script interpreted after originating a callback dial-up connection.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.1.1.17

ipadModemDialCallbackRspScript

Callback security challenge response script interpreted after answering a callback dial-up connection.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.1.1.18

ipadModemDataTable

table

.1.3.6.1.4.1.321.100.1.8.2 · 1 row entry · 12 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadModemDataTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadModemDataTable'

Table of modem database parameters.

ipadModemDataTableEntry row .1.3.6.1.4.1.321.100.1.8.2.1

An entry in the ipad modem database parameters table.

Indexes

ipadModemDataTableIndex

Column Syntax OID

ipadModemDataTableIndex

The index into the ipad modem database parameters table.

ipadModemDataDialingScript

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.2.1.1

ipadModemDataModemName

Identification string for the modem database.

OctetStringr/w

Constraints:
range: 0-10

.1.3.6.1.4.1.321.100.1.8.2.1.2

ipadModemDataSetupScript

First script interpreted when a modem port is initialized.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.2.1.3

Script interpreted when a dial-up connection is initiated.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.2.1.4

ipadModemDataAnswerScript

Script interpreted when a modem port decides to answer an incoming call.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.2.1.5

ipadModemDataHangupScript

Script interpreted when a dial-up connection is no longer needed.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.2.1.6

ipadModemDataSyncScript

Script interpreted to configure the modem to pass synchronous data.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.2.1.7

ipadModemDataSyncMethod

This object specifies how synchronous user data is passed to the modem.

none - The modem does not support synchronous user data.
sync - The modem directly supports synchronous user data.
v80 - Synchronous…

Enumerationr/w

Enumerated Values:

1	other
2	none
3	sync
4	v80
5	rfc1662
6	v80crc

.1.3.6.1.4.1.321.100.1.8.2.1.8

ipadModemDataSetupScript2

Second script interpreted when a modem port is initialized.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.2.1.9

ipadModemDataSetupScript3

Third script interpreted when a modem port is initialized.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.2.1.10

ipadModemDataSetupScript4

Fourth script interpreted when a modem port is initialized.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.2.1.11

ipadModemDataSetupScript5

Fifth script interpreted when a modem port is initialized.

OctetStringr/w

Constraints:
range: 0-60

.1.3.6.1.4.1.321.100.1.8.2.1.12

ipadDbuTable

table

.1.3.6.1.4.1.321.100.1.8.3 · 1 row entry · 9 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadDbuTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadDbuTable'

The Dial Backup configuration table.

ipadDbuTableEntry row .1.3.6.1.4.1.321.100.1.8.3.1

An entry in the Dial Backup configuration table.

Indexes

ipadDbuIndex

Column Syntax OID

ipadDbuIndex

An index into the Dial Backup configuration table.
Equivalent to MIB-II ifIndex.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.3.1.1

ipadDbuOperation

This object specifes the basic operation of the Dial Backup feature.

disable - Dial Backup is not to operate
automatic - Dial Backup will start and end automatically
automaticDaily - Dial Backup will oper…

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	automatic
4	automaticDaily
5	forceBackup
6	testOriginate
7	testAnswer

.1.3.6.1.4.1.321.100.1.8.3.1.2

ipadDbuMonitoredifIndex

Network MIB-II ifIndex monitored by Dial Backup.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.3.1.7

ipadDbuActivator1

This object specifies what will trigger a dial backup activation.

disable - No alarm will trigger
any - Trigger on any active alarm listed here
carrier - Trigger on LOS, OOF, or OOS alarms
es - Trigger on…

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	any
4	carrier
5	es
6	ses
7	uas
8	los
9	cs
10	bpv
11	oof
12	ais
13	ras
14	oos

.1.3.6.1.4.1.321.100.1.8.3.1.8

ipadDbuActivator2

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	any
4	carrier
5	es
6	ses
7	uas
8	los
9	cs
10	bpv
11	oof
12	ais
13	ras
14	oos

.1.3.6.1.4.1.321.100.1.8.3.1.9

ipadDbuRevertDelay

This object specifies the number of seconds the dial backup activators must be continuously gone before the normal connection is restored.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.3.1.10

ipadDbuTrapDelay

This object specifies the number of seconds after entering the active state before sending the Dial Backup trap.

ipadDbuDailyIndex ipadDbuDailyDayOfWeek

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.3.1.11

ipadDbuStatus

This object reports the current activity of the Dial Backup feature

disabled - The feature is not enabled
setup - The feature is configuring the modem
error - The feature could not setup the modem
standby…

Enumeration

Enumerated Values:

1	other
2	disabled
3	standby
4	disallowed
5	dialing
6	answering
7	negotiating
8	awaitingCallback
9	active
10	disconnecting
11	testWaiting
12	testPassed
13	testFailed
14	error
15	setup
16	dialWait
17	ringing

.1.3.6.1.4.1.321.100.1.8.3.1.12

ipadDbuTrap

Enable or disable the Dial Backup trap.

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	enable

.1.3.6.1.4.1.321.100.1.8.3.1.13

ipadDbuDailyTable

table

.1.3.6.1.4.1.321.100.1.8.4 · 1 row entry · 4 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadDbuDailyTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadDbuDailyTable'

The Daily Dial Backup Times Table.

ipadDbuDailyTableEntry row .1.3.6.1.4.1.321.100.1.8.4.1

An entry in the Daily Dial Backup Times Table.

Indexes

Column Syntax OID

ipadDbuDailyIndex

An index into the Daily Dial Backup Times Table.
Equivalent to MIB-II ifIndex.

ipadFrPortStatsService ipadFrPortStatsPeriod

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.8.4.1.1

ipadDbuDailyDayOfWeek

This is the day of the week index into the Daily Dial Backup Times Table.

Enumeration

Enumerated Values:

1	sunday
2	monday
3	tuesday
4	wednesday
5	thursday
6	friday
7	saturday

.1.3.6.1.4.1.321.100.1.8.4.1.2

ipadDbuDailyStart

This object is the beginning of a window for Dial Backup activation.

Enumerationr/w

Enumerated Values:

1	hour00
2	hour01
3	hour02
4	hour03
5	hour04
6	hour05
7	hour06
8	hour07
9	hour08
10	hour09
11	hour10
12	hour11
13	hour12
14	hour13
15	hour14
16	hour15
17	hour16
18	hour17
19	hour18
20	hour19
21	hour20
22	hour21
23	hour22
24	hour23

.1.3.6.1.4.1.321.100.1.8.4.1.3

ipadDbuDailyLength

This object is the size of a window for Dial Backup activation.

Enumerationr/w

Enumerated Values:

1	disable
2	hour01
3	hour02
4	hour03
5	hour04
6	hour05
7	hour06
8	hour07
9	hour08
10	hour09
11	hour10
12	hour11
13	hour12
14	hour13
15	hour14
16	hour15
17	hour16
18	hour17
19	hour18
20	hour19
21	hour20
22	hour21
23	hour22
24	hour23
25	hour24

.1.3.6.1.4.1.321.100.1.8.4.1.4

ipadFrPortStatsTable

table

.1.3.6.1.4.1.321.100.1.9.1 · 1 row entry · 38 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadFrPortStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadFrPortStatsTable'

Port statistics.

ipadFrPortStatsEntry row .1.3.6.1.4.1.321.100.1.9.1.1

An entry in the service aware ports statistics table.

Indexes

Column Syntax OID

ipadFrPortStatsService

Port index in the ipadFrPortStats table;
an entry in the ipad service table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.1

ipadFrPortStatsPeriod

The index into the port stats 24-hour table.

Enumeration

Enumerated Values:

1	portStatsSummary
2	portStatsCurrent
3	portStatsperiod1
4	portStatsperiod2
5	portStatsperiod3
6	portStatsperiod4
7	portStatsperiod5
8	portStatsperiod6
9	portStatsperiod7
10	portStatsperiod8
11	portStatsperiod9
12	portStatsperiod10
13	portStatsperiod11
14	portStatsperiod12
15	portStatsperiod13
16	portStatsperiod14
17	portStatsperiod15
18	portStatsperiod16
19	portStatsperiod17
20	portStatsperiod18
21	portStatsperiod19
22	portStatsperiod20
23	portStatsperiod21
24	portStatsperiod22
25	portStatsperiod23
26	portStatsperiod24
27	portStatsperiod25
28	portStatsperiod26
29	portStatsperiod27
30	portStatsperiod28
31	portStatsperiod29
32	portStatsperiod30
33	portStatsperiod31
34	portStatsperiod32
35	portStatsperiod33
36	portStatsperiod34
37	portStatsperiod35
38	portStatsperiod36
39	portStatsperiod37
40	portStatsperiod38
41	portStatsperiod39
42	portStatsperiod40
43	portStatsperiod41
44	portStatsperiod42
45	portStatsperiod43
46	portStatsperiod44
47	portStatsperiod45
48	portStatsperiod46
49	portStatsperiod47
50	portStatsperiod48
51	portStatsperiod49
52	portStatsperiod50
53	portStatsperiod51
54	portStatsperiod52
55	portStatsperiod53
56	portStatsperiod54
57	portStatsperiod55
58	portStatsperiod56
59	portStatsperiod57
60	portStatsperiod58
61	portStatsperiod59
62	portStatsperiod60
63	portStatsperiod61
64	portStatsperiod62
65	portStatsperiod63
66	portStatsperiod64
67	portStatsperiod65
68	portStatsperiod66
69	portStatsperiod67
70	portStatsperiod68
71	portStatsperiod69
72	portStatsperiod70
73	portStatsperiod71
74	portStatsperiod72
75	portStatsperiod73
76	portStatsperiod74
77	portStatsperiod75
78	portStatsperiod76
79	portStatsperiod77
80	portStatsperiod78
81	portStatsperiod79
82	portStatsperiod80
83	portStatsperiod81
84	portStatsperiod82
85	portStatsperiod83
86	portStatsperiod84
87	portStatsperiod85
88	portStatsperiod86
89	portStatsperiod87
90	portStatsperiod88
91	portStatsperiod89
92	portStatsperiod90
93	portStatsperiod91
94	portStatsperiod92
95	portStatsperiod93
96	portStatsperiod94
97	portStatsperiod95
98	portStatsperiod96

.1.3.6.1.4.1.321.100.1.9.1.1.2

ipadFrPortStatsTxFrames

Number of transmitted frames for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.3

ipadFrPortStatsRxFrames

Number of received frames for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.4

ipadFrPortStatsTxOctets

Number of transmitted octets for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.5

ipadFrPortStatsRxOctets

Number of received octets for the period.

ipadFrPortStatsTxMgmtFrames

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.6

Number of transmitted management frames for the period.

ipadFrPortStatsRxMgmtFrames

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.7

Number of received management frames for the period.

ipadFrPortStatsTxMgmtOctets

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.8

Number of transmitted management octets for the period.

ipadFrPortStatsRxMgmtOctets

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.9

Number of received management octets for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.10

ipadFrPortStatsRxFECN

Number of received frames with FECN set for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.11

ipadFrPortStatsRxBECN

Number of received frames with BECN set for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.12

ipadFrPortStatsRxInvalid

Number of invalid received frames for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.13

ipadFrPortStatsTxStatInq

Number of transmitted status inquiry frames for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.14

ipadFrPortStatsRxStatInq

Number of received status inquiry frames for the period.

ipadFrPortStatsTxStatResp

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.15

Number of transmitted status response frames for the period.

ipadFrPortStatsRxStatResp

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.16

Number of received status response frames for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.17

ipadFrPortStatsRxInvLMI

Number of received frames with an invalid LMI for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.18

ipadFrPortStatsPeak

Peak throughput rate for the period (in bits/second).

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.19

ipadFrPortStatsAverage

Average throughput rate for the period (in bits/second).

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.20

ipadFrPortStatsTimeStamp

The value of sysUpTime the last time the statistics were updated.

ipadFrPortStatsTxAvgPercent

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.321.100.1.9.1.1.21

Average Tx throughput percent for the period.

ipadFrPortStatsTxMaxPercent

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.22

Maximum Tx throughput percent for the period.

ipadFrPortStatsTxInstantPercent

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.23

Instantaneous Tx throughput percent for the period.

ipadFrPortStatsTx20PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.24

Number of seconds Tx throughput was 0-20% of bandwidth.

ipadFrPortStatsTx40PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.25

Number of seconds Tx throughput was 21-40% of bandwidth.

ipadFrPortStatsTx60PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.26

Number of seconds Tx throughput was 41-60% of bandwidth.

ipadFrPortStatsTx80PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.27

Number of seconds Tx throughput was 61-80% of bandwidth.

ipadFrPortStatsTx100PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.28

Number of seconds Tx throughput was 81-100% of bandwidth.

ipadFrPortStatsRxAvgPercent

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.29

Average Rx throughput percent for the period.

ipadFrPortStatsRxMaxPercent

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.30

Maximum Rx throughput percent for the period.

ipadFrPortStatsRxInstantPercent

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.31

Instantaneous Rx throughput percent for the period.

ipadFrPortStatsRx20PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.32

Number of seconds Rx throughput was 0-20% of bandwidth.

ipadFrPortStatsRx40PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.33

Number of seconds Rx throughput was 21-40% of bandwidth.

ipadFrPortStatsRx60PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.34

Number of seconds Rx throughput was 41-60% of bandwidth.

ipadFrPortStatsRx80PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.35

Number of seconds Rx throughput was 61-80% of bandwidth.

ipadFrPortStatsRx100PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.36

Number of seconds Rx throughput was 81-100% of bandwidth.

ipadFrPortStatsValidIntervals

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.1.1.37

Number of valid intervals in the table excluding the Summary and Current entries.

Integer32

Constraints:
range: 0-96

.1.3.6.1.4.1.321.100.1.9.1.1.38

ipadDLCIstatsTable

table

.1.3.6.1.4.1.321.100.1.9.2 · 1 row entry · 52 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadDLCIstatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadDLCIstatsTable'

Port statistics.

ipadDLCIstatsEntry row .1.3.6.1.4.1.321.100.1.9.2.1

An entry in the service aware DLCI statistics table.

Indexes

ipadDLCIstatsService ipadDLCIstatsDLCI ipadDLCIstatsPeriod

Column Syntax OID

ipadDLCIstatsService

The service index for the service aware stats table; identifies an
entry in the ipad DLCI table when combined with ipadDLCIstatsDLCI.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.1

ipadDLCIstatsDLCI

The DLCI index for the service aware stats table; identifies an
entry in the ipad DLCI table when combined with ipadDLCIstatsService.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.2

ipadDLCIstatsPeriod

The index into the DLCI stats 24-hour table.

Enumeration

Enumerated Values:

1	dlciStatsSummary
2	dlciStatsCurrent
3	dlciStatsperiod1
4	dlciStatsperiod2
5	dlciStatsperiod3
6	dlciStatsperiod4
7	dlciStatsperiod5
8	dlciStatsperiod6
9	dlciStatsperiod7
10	dlciStatsperiod8
11	dlciStatsperiod9
12	dlciStatsperiod10
13	dlciStatsperiod11
14	dlciStatsperiod12
15	dlciStatsperiod13
16	dlciStatsperiod14
17	dlciStatsperiod15
18	dlciStatsperiod16
19	dlciStatsperiod17
20	dlciStatsperiod18
21	dlciStatsperiod19
22	dlciStatsperiod20
23	dlciStatsperiod21
24	dlciStatsperiod22
25	dlciStatsperiod23
26	dlciStatsperiod24
27	dlciStatsperiod25
28	dlciStatsperiod26
29	dlciStatsperiod27
30	dlciStatsperiod28
31	dlciStatsperiod29
32	dlciStatsperiod30
33	dlciStatsperiod31
34	dlciStatsperiod32
35	dlciStatsperiod33
36	dlciStatsperiod34
37	dlciStatsperiod35
38	dlciStatsperiod36
39	dlciStatsperiod37
40	dlciStatsperiod38
41	dlciStatsperiod39
42	dlciStatsperiod40
43	dlciStatsperiod41
44	dlciStatsperiod42
45	dlciStatsperiod43
46	dlciStatsperiod44
47	dlciStatsperiod45
48	dlciStatsperiod46
49	dlciStatsperiod47
50	dlciStatsperiod48
51	dlciStatsperiod49
52	dlciStatsperiod50
53	dlciStatsperiod51
54	dlciStatsperiod52
55	dlciStatsperiod53
56	dlciStatsperiod54
57	dlciStatsperiod55
58	dlciStatsperiod56
59	dlciStatsperiod57
60	dlciStatsperiod58
61	dlciStatsperiod59
62	dlciStatsperiod60
63	dlciStatsperiod61
64	dlciStatsperiod62
65	dlciStatsperiod63
66	dlciStatsperiod64
67	dlciStatsperiod65
68	dlciStatsperiod66
69	dlciStatsperiod67
70	dlciStatsperiod68
71	dlciStatsperiod69
72	dlciStatsperiod70
73	dlciStatsperiod71
74	dlciStatsperiod72
75	dlciStatsperiod73
76	dlciStatsperiod74
77	dlciStatsperiod75
78	dlciStatsperiod76
79	dlciStatsperiod77
80	dlciStatsperiod78
81	dlciStatsperiod79
82	dlciStatsperiod80
83	dlciStatsperiod81
84	dlciStatsperiod82
85	dlciStatsperiod83
86	dlciStatsperiod84
87	dlciStatsperiod85
88	dlciStatsperiod86
89	dlciStatsperiod87
90	dlciStatsperiod88
91	dlciStatsperiod89
92	dlciStatsperiod90
93	dlciStatsperiod91
94	dlciStatsperiod92
95	dlciStatsperiod93
96	dlciStatsperiod94
97	dlciStatsperiod95
98	dlciStatsperiod96

.1.3.6.1.4.1.321.100.1.9.2.1.3

ipadDLCIstatsTxFrames

The number of transmitted frames for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.4

ipadDLCIstatsRxFrames

The number of received frames for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.5

ipadDLCIstatsTxOctets

The number of transmitted octets for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.6

ipadDLCIstatsRxOctets

The number of received octets for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.7

ipadDLCIstatsRxFECN

The number of received frames with FECN set for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.8

ipadDLCIstatsRxBECN

The number of received frames with BECN set for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.9

ipadDLCIstatsRxDE

The number of received frames with DE bit set for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.10

ipadDLCIstatsTxExcessCIR

The number of transmitted octets in excess of CIR for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.11

ipadDLCIstatsTxExcessBe

The number of transmitted octets in excess of Be for the period.

ipadDLCIstatsTxMgmtFrames

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.12

The number of transmitted management frames for the period.

ipadDLCIstatsRxMgmtFrames

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.13

The number of received management frames for the period.

ipadDLCIstatsTxMgmtOctets

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.14

The number of transmitted management octets for the period.

ipadDLCIstatsRxMgmtOctets

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.15

The number of received management octets for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.16

ipadDLCIstatsPeak

Peak throughput rate for the period (in bits/second).

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.17

ipadDLCIstatsAverage

Average throughput rate for the period (in bits/second).

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.18

ipadDLCIstatsDelayPeak

Peak roundtrip delay for the period.

ipadDLCIstatsDelayAverage

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.19

Average roundtrip delay for the period.

ipadDLCIstatsRoundTripTimeouts

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.20

Number of timeouts on roundtrip delay for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.21

ipadDLCIstatsUAS

Number of seconds the DLCI is unavailable.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.22

ipadDLCIstatsFdrCir

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.23

ipadDLCIstatsDdrCir

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.24

ipadDLCIstatsFdrBe

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.25

ipadDLCIstatsDdrBe

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.26

ipadDLCIstatsTimeStamp

The value of sysUpTime the last time the statistics were updated.

ipadDLCIstatsRemoteFramesOfferedWithinCIR

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.321.100.1.9.2.1.27

Count of frames sent within CIR from the remote end of the DLCI.

ipadDLCIstatsRemoteFramesOfferedWithinBE

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.28

Count of frames sent within BE, but over CIR, from the remote end of the DLCI.

ipadDLCIstatsFramesReceived

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.29

Count of frames received by the local device on this DLCI.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.30

ipadDLCIstatsFDRCIR

Frame Delivery Ratio calculated within CIR.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.321.100.1.9.2.1.31

ipadDLCIstatsFDRBE

Frame Delivery Ratio caclulated within BE.

ipadDLCIstatsRemoteDataOfferedWithinCIR

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.321.100.1.9.2.1.32

Count of data octets sent within CIR from the remote end of the DLCI.

ipadDLCIstatsRemoteDataOfferedWithinBE

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.33

Count of data octets sent within BE, but over CIR, from the remote
end of the DLCI.

ipadDLCIstatsDataReceived

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.34

Count of data octets received by the local device on this DLCI.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.35

ipadDLCIstatsDDRCIR

Data Delivery Ratio calculated within CIR.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.321.100.1.9.2.1.36

ipadDLCIstatsDDRBE

Data Delivery Ratio caclulated within BE.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.321.100.1.9.2.1.37

ipadDLCIstatsAvgPercent

Average throughput percent for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.38

ipadDLCIstatsMaxPercent

Maximum throughput percent for the period.

ipadDLCIstatsInstantPercent

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.39

Instantaneous throughput percent for the period.

ipadDLCIstats20PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.40

Number of seconds throughput was 0-20% of bandwidth.

ipadDLCIstats40PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.41

Number of seconds throughput was 21-40% of bandwidth.

ipadDLCIstats60PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.42

Number of seconds throughput was 41-60% of bandwidth.

ipadDLCIstats80PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.43

Number of seconds throughput was 61-80% of bandwidth.

ipadDLCIstats100PercentSec

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.44

Number of seconds throughput was 81-100% of bandwidth.

ipadDLCIstatsValidIntervals

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.45

Number of valid intervals in the table excluding the Summary and Current entries.

Integer32

Constraints:
range: 0-96

.1.3.6.1.4.1.321.100.1.9.2.1.46

ipadDLCIstatsCompressionTxOctetsIn

Number of octets passed into the compression engine.

ipadDLCIstatsCompressionTxOctetsOut

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.47

Number of octets passed out of the compression engine.

ipadDLCIstatsCompressionRxOctetsIn

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.48

Number of octets passed into the compression engine.

ipadDLCIstatsCompressionRxOctetsOut

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.49

Number of octets passed out of the compression engine.

ipadDLCIstatsCompressionTxRatio

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.2.1.50

Compression Ratio calculated in the transmit direction.

ipadDLCIstatsCompressionRxRatio

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.321.100.1.9.2.1.51

Compression Ratio calculation in the receive direction.

ipadUserStatsIndex ipadUserStatsPeriod

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.321.100.1.9.2.1.52

ipadUserStatsTable

table

.1.3.6.1.4.1.321.100.1.9.3 · 1 row entry · 9 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadUserStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadUserStatsTable'

User-selected protocol statistics.

ipadUserStatsEntry row .1.3.6.1.4.1.321.100.1.9.3.1

An entry in the user statistics table.

Indexes

Column Syntax OID

ipadUserStatsIndex

Index into the user statistics table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.3.1.1

ipadUserStatsPeriod

The index into the user stats 24-hour table.

Enumeration

Enumerated Values:

1	userStatsSummary
2	userStatsCurrent
3	userStatsperiod1
4	userStatsperiod2
5	userStatsperiod3
6	userStatsperiod4
7	userStatsperiod5
8	userStatsperiod6
9	userStatsperiod7
10	userStatsperiod8
11	userStatsperiod9
12	userStatsperiod10
13	userStatsperiod11
14	userStatsperiod12
15	userStatsperiod13
16	userStatsperiod14
17	userStatsperiod15
18	userStatsperiod16
19	userStatsperiod17
20	userStatsperiod18
21	userStatsperiod19
22	userStatsperiod20
23	userStatsperiod21
24	userStatsperiod22
25	userStatsperiod23
26	userStatsperiod24
27	userStatsperiod25
28	userStatsperiod26
29	userStatsperiod27
30	userStatsperiod28
31	userStatsperiod29
32	userStatsperiod30
33	userStatsperiod31
34	userStatsperiod32
35	userStatsperiod33
36	userStatsperiod34
37	userStatsperiod35
38	userStatsperiod36
39	userStatsperiod37
40	userStatsperiod38
41	userStatsperiod39
42	userStatsperiod40
43	userStatsperiod41
44	userStatsperiod42
45	userStatsperiod43
46	userStatsperiod44
47	userStatsperiod45
48	userStatsperiod46
49	userStatsperiod47
50	userStatsperiod48
51	userStatsperiod49
52	userStatsperiod50
53	userStatsperiod51
54	userStatsperiod52
55	userStatsperiod53
56	userStatsperiod54
57	userStatsperiod55
58	userStatsperiod56
59	userStatsperiod57
60	userStatsperiod58
61	userStatsperiod59
62	userStatsperiod60
63	userStatsperiod61
64	userStatsperiod62
65	userStatsperiod63
66	userStatsperiod64
67	userStatsperiod65
68	userStatsperiod66
69	userStatsperiod67
70	userStatsperiod68
71	userStatsperiod69
72	userStatsperiod70
73	userStatsperiod71
74	userStatsperiod72
75	userStatsperiod73
76	userStatsperiod74
77	userStatsperiod75
78	userStatsperiod76
79	userStatsperiod77
80	userStatsperiod78
81	userStatsperiod79
82	userStatsperiod80
83	userStatsperiod81
84	userStatsperiod82
85	userStatsperiod83
86	userStatsperiod84
87	userStatsperiod85
88	userStatsperiod86
89	userStatsperiod87
90	userStatsperiod88
91	userStatsperiod89
92	userStatsperiod90
93	userStatsperiod91
94	userStatsperiod92
95	userStatsperiod93
96	userStatsperiod94
97	userStatsperiod95
98	userStatsperiod96

.1.3.6.1.4.1.321.100.1.9.3.1.2

ipadUserStatsTxFrames

Number of transmitted frames for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.3.1.3

ipadUserStatsRxFrames

Number of received frames for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.3.1.4

ipadUserStatsTxOctets

Number of transmitted octets for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.3.1.5

ipadUserStatsRxOctets

Number of received octets for the period.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.3.1.6

ipadUserStatsTxRatePeak

Peak throughput rate for the period (in bits/second).

ipadUserStatsTxRateAverage

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.3.1.7

Average throughput rate for the period (in bits/second).

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.9.3.1.8

ipadUserStatsTimeStamp

The value of sysUpTime the last time the statistics were updated.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.321.100.1.9.3.1.9

ipadIPTopNStatsTable

table

.1.3.6.1.4.1.321.100.1.9.4 · 1 row entry · 7 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadIPTopNStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadIPTopNStatsTable'

IP TopN statistics.

ipadIPTopNStatsEntry row .1.3.6.1.4.1.321.100.1.9.4.1

An entry in the user statistics table.

Indexes

ipadIPTopNStatsIndex

Column	Syntax	OID
ipadIPTopNStatsIndex Index into the IP TopN statistics table.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.9.4.1.1`
ipadIPTopNStatsAddress IP address of this entry.	OctetString Constraints: `range: 1-16`	`.1.3.6.1.4.1.321.100.1.9.4.1.2`
ipadIPTopNStatsTimestamp Time of last IP frame for this entry.	SNMPv2-SMITimeTicks Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.321.100.1.9.4.1.3`
ipadIPTopNStatsRxFrames Number of received IP frames for this entry.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.9.4.1.4`
ipadIPTopNStatsRxOctets Number of received IP octets for this entry.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.9.4.1.5`
ipadIPTopNStatsTxFrames Number of transmitted IP frames for this entry.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.9.4.1.6`
ipadIPTopNStatsTxOctets Number of transmitted IP octets for this entry.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.9.4.1.7`

ipadPktSwCfgTable

table

.1.3.6.1.4.1.321.100.1.10.2 · 1 row entry · 21 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadPktSwCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadPktSwCfgTable'

The ipad packet switch configuration table.

ipadPktSwCfgTableEntry row .1.3.6.1.4.1.321.100.1.10.2.1

An entry in the ipad packet switch configuration table.

Indexes

ipadPktSwCfgService

Column Syntax OID

ipadPktSwCfgService

The index into the packet switch configuration table;
an entry in the ipad Service table.

ipadPktSwCfgInterfaceType

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.10.2.1.1

Network ports should be set to User Network Interface (uni)
and user ports should be set to Network Interface (ni).

Enumerationr/w

Enumerated Values:

1	uni
2	ni
3	nni

.1.3.6.1.4.1.321.100.1.10.2.1.2

ipadPktSwCfgLnkMgmtType

If set to auto, the frame relay LMI type will
be learned from the network side. If set to
none, all DLCI must be configured.

Enumerationr/w

Enumerated Values:

1	other
2	auto
3	ccitt
4	ansi
5	lmi
6	none

.1.3.6.1.4.1.321.100.1.10.2.1.3

ipadPktSwCfgMaxFrameSize

This is the maximum frame size configured in the frame relay network.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.10.2.1.4

ipadPktSwCfgnN1

Number of keep alive requests between full status request.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.10.2.1.5

ipadPktSwCfgnN2

Number of errors from FRAD before alarm.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.10.2.1.6

ipadPktSwCfgnN3

Number of events to sample nN2.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.10.2.1.7

ipadPktSwCfgnT1

Delay before issuing a poll sequence.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.10.2.1.8

ipadPktSwCfgDefCIR

Default committed information rate in bits per second.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.10.2.1.9

ipadPktSwCfgDefExBurst

Default excess burst rate in bits per second.

ipadPktSwCfgLinkInjection

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.10.2.1.10

ipadPktSwCfgCIREE

Determines if the interface will enforce CIR and
excess burst configured values.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.10.2.1.11

Indicates how to process frames in excess
of the CIR when congestion exists.

Enumerationr/w

Enumerated Values:

1	other
2	standard
3	buffered
4	forced

.1.3.6.1.4.1.321.100.1.10.2.1.12

ipadPktSwCfgAutoDiagnostic

Determines if the unit will put itself into
diagnostic mode everytime it determines that
there are no LMI received on a network service.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.10.2.1.13

ipadPktSwCfgAutoDiscovery

Determines if the unit will learn the DLCIs
from the LMMI received on this service.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.10.2.1.14

ipadPktSwCfgMgmtDLCI

Specifies the DLCI that will be used by the unit
for management information. Specifying a 0 disables
this feature.

Integer32r/w

Constraints:
range: 0-4096

.1.3.6.1.4.1.321.100.1.10.2.1.15

ipadPktSwCfgRoundTripDelaySize

Specifies the packet size in octets used to calculate
round trip delay.

Integer32r/w

Constraints:
range: 16-1500

.1.3.6.1.4.1.321.100.1.10.2.1.16

ipadPktSwCfgRoundTripDelayRate

Specifies the packet rate in seconds used to calculate
round trip delay.

Integer32r/w

Constraints:
range: 1-900

.1.3.6.1.4.1.321.100.1.10.2.1.17

ipadPktSwCfgAutoIPMgmtAddr

Look for DLCI (980-995) and uses its IP address.

Enumerationr/w

Enumerated Values:

1	other
2	no
3	yes

.1.3.6.1.4.1.321.100.1.10.2.1.18

ipadPktSwCfgNormalTxQueueSize

The depth of the normal priority tx queue. This size determines the
max number of low priority packets that can be queued in front of high
priority traffic.

Integer32r/w

Constraints:
range: 1-32

.1.3.6.1.4.1.321.100.1.10.2.1.19

ipadPktSwCfgAddDLCI

Identifies a DLCI number to be added.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.10.2.1.20

ipadPktSwCfgDeleteDLCI

Identifies a DLCI number to be deleted.

ipadMiscPortSettingsIndex

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.10.2.1.21

ipadTrapDestTable

table

.1.3.6.1.4.1.321.100.1.11.1 · 1 row entry · 2 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadTrapDestTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadTrapDestTable'

The ipad trap destination table.

ipadTrapDestTableEntry row .1.3.6.1.4.1.321.100.1.11.1.1

An entry in the ipad trap destination table.

Indexes

ipadTrapDestIndex

Column	Syntax	OID
ipadTrapDestIndex Index into the ipad trap destination table.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.11.1.1.1`
ipadTrapDestination Trap destination.	SNMPv2-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.321.100.1.11.1.1.2`

ipadMiscPortSettings

table

.1.3.6.1.4.1.321.100.1.12.1 · 1 row entry · 3 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadMiscPortSettings

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadMiscPortSettings'

The ipad miscellaneous port settings table.

ipadMiscPortSettingsEntry row .1.3.6.1.4.1.321.100.1.12.1.1

An entry in the ipad miscellaneous port settings table.

Indexes

Column Syntax OID

ipadMiscPortSettingsIndex

The MIB-II ifIndex for this port.

ipadMiscPortSettingsSerialType

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.12.1.1.1

The type of this serial port.

Enumerationr/w

Enumerated Values:

1	other
2	dce
3	dte

.1.3.6.1.4.1.321.100.1.12.1.1.2

ipadMiscPortSettingsModemControl

Request the attached service to use the modem dialing control feature.

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	enable

.1.3.6.1.4.1.321.100.1.12.1.1.3

ipadMiscShdslConfigTable

table

.1.3.6.1.4.1.321.100.1.12.4 · 1 row entry · 6 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadMiscShdslConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadMiscShdslConfigTable'

The ipad miscellaneous SHDSL configuration table.

ipadMiscShdslConfigEntry row .1.3.6.1.4.1.321.100.1.12.4.1

An entry in the ipad miscellaneous SHDSL configuration table.

Indexes

ipadMiscShdslConfigIndex

Column Syntax OID

ipadMiscShdslConfigIndex

This object is the index into the SHDSL configuration table.

ipadMiscShdslTerminalType

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.12.4.1.1

Selects whether the tu is a central or remote site terminal unit.
Applicable to HDSL2/SHDSL only.

Enumerationr/w

Enumerated Values:

1	other
2	isXtuC
3	isXtuR

.1.3.6.1.4.1.321.100.1.12.4.1.2

ipadMiscShdslTiming

Sets the timing source to synchronize the unit's internal timing generators.

Enumerationr/w

Enumerated Values:

1	shdslTimingOther
2	shdslTimingInternal
3	shdslTimingNetwork
4	shdslTimingEqDTE
5	shdslTimingStation
6	shdslTimingPort1
7	shdslTimingPort2

.1.3.6.1.4.1.321.100.1.12.4.1.3

ipadMiscShdslStationInTiming

Selects the input timing if SHDSLTiming is set to Station.

Enumerationr/w

Enumerated Values:

1	shdslStationInTimingOther
2	shdslStationInTimingNX64
3	shdslStationInTiming1544
4	shdslStationInTiming2048

.1.3.6.1.4.1.321.100.1.12.4.1.4

ipadMiscShdslStationTimingNxMultiple

Selects the N-multiple when Station Input Timing is set to either NX56 or NX65.

ipadMiscShdslAutomaticRetrain

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.12.4.1.5

Enable or disable automatic line retraining when needed.
Enable is the default. Disable is used for PSD measurement.

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	enable

.1.3.6.1.4.1.321.100.1.12.4.1.6

ipadMiscShdslStatusTable

table

.1.3.6.1.4.1.321.100.1.12.5 · 1 row entry · 7 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadMiscShdslStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadMiscShdslStatusTable'

The ipad miscellaneous SHDSL status table.

ipadMiscShdslStatusEntry row .1.3.6.1.4.1.321.100.1.12.5.1

An entry in the ipad miscellaneous SHDSL status table.

Indexes

ipadMiscShdslStatusIndex

Column Syntax OID

ipadMiscShdslStatusIndex

This object is the index into the SHDSL configuration table.

ipadMiscShdslConnectionStatus

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.12.5.1.1

This object displays the connection status of Wire Pair 1 of an SHDSL connection.

Enumeration

Enumerated Values:

1	idle
2	handshake
3	training
4	data

.1.3.6.1.4.1.321.100.1.12.5.1.2

ipadMiscShdslDetailedConnectionStatus

This object displays the detailed connection status of Wire Pair 1 of an SHDSL connection.

OctetString

Constraints:
range: 0-20

.1.3.6.1.4.1.321.100.1.12.5.1.3

ipadMiscShdslEOCInMessages

This object displays the number of EOC messages received.

ipadMiscShdslEOCOutMessages

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.12.5.1.4

This object displays the number of EOC messages transmitted.

ipadMiscShdslConnectionStatusPair2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.12.5.1.5

This object displays the connection status of Wire Pair 2 of an SHDSL connection.

Enumeration

Enumerated Values:

1	idle
2	handshake
3	training
4	data

.1.3.6.1.4.1.321.100.1.12.5.1.6

ipadMiscShdslDetailedConnectionStatusPair2

This object displays the detailed connection status of Wire Pair 2 of an SHDSL connection.

OctetString

Constraints:
range: 0-20

.1.3.6.1.4.1.321.100.1.12.5.1.7

ipadSoftKeyTable

table

.1.3.6.1.4.1.321.100.1.14.1 · 1 row entry · 4 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadSoftKeyTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadSoftKeyTable'

Table of software keys.

ipadSoftKeyTableEntry row .1.3.6.1.4.1.321.100.1.14.1.1

An entry in the software key table.

Indexes

ipadSoftKeyIndex

Column	Syntax	OID
ipadSoftKeyIndex Index into the ipad software key table.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.14.1.1.1`
ipadSoftKeyAcronym Three-letter acronym for software key.	OctetString Constraints: `range: 0-3`	`.1.3.6.1.4.1.321.100.1.14.1.1.2`
ipadSoftKeyDescription Description, if available, of this software key.	OctetString Constraints: `range: 0-80`	`.1.3.6.1.4.1.321.100.1.14.1.1.3`
ipadSoftKeyExpirationDate Expiration date of this software key in the format YY/MM/DD.	OctetString Constraints: `range: 0-8`	`.1.3.6.1.4.1.321.100.1.14.1.1.4`

ipadTCPServerConnTable

table

.1.3.6.1.4.1.321.100.1.15.2 · 1 row entry · 4 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadTCPServerConnTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadTCPServerConnTable'

Table of TCP Server connections.

ipadTCPServerConnTableEntry row .1.3.6.1.4.1.321.100.1.15.2.1

An entry in the TCP Server connection table.

Indexes

ipadTCPServerConnIndex

Column Syntax OID

ipadTCPServerConnIndex

Index into the ipad TCP Server Connection table.

ipadTCPServerConnEndpoint

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.15.2.1.1

Identifies the endpoint for this connection.

OctetStringr/w

Constraints:
range: 0-11

.1.3.6.1.4.1.321.100.1.15.2.1.2

ipadTCPServerConnLocalPort

Identifies the TCP port for this connection (default: 2000).

Integer32r/w

Constraints:
range: 1-65535

.1.3.6.1.4.1.321.100.1.15.2.1.3

ipadTCPServerConnEnableEntry

Enables or disables this entry.

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	enable

.1.3.6.1.4.1.321.100.1.15.2.1.4

ipadTCPServerHostAccessTable

table

.1.3.6.1.4.1.321.100.1.15.5 · 1 row entry · 2 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadTCPServerHostAccessTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadTCPServerHostAccessTable'

Table of TCP Server IP Host Access List.

ipadTCPServerHostAccessTableEntry row .1.3.6.1.4.1.321.100.1.15.5.1

An entry in the TCP Server Host Access List table.

Indexes

ipadTCPServerHostAccessIndex

Column	Syntax	OID
ipadTCPServerHostAccessIndex Index into the ipad trap destination table.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.15.5.1.1`
ipadTCPServerHostAccessIPAddr Trap destination.	SNMPv2-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.321.100.1.15.5.1.2`

ipadSCADAConfigTable

table

.1.3.6.1.4.1.321.100.1.16.1 · 1 row entry · 9 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadSCADAConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadSCADAConfigTable'

The SCADA config table.

ipadSCADAConfigTableEntry row .1.3.6.1.4.1.321.100.1.16.1.1

An entry in the SCADA config table.

Indexes

ipadSCADACfgIndex

Column Syntax OID

ipadSCADACfgIndex

The index for SCADA config table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.16.1.1.1

ipadSCADACfgMessageSize

The SCADA message size.

ipadSCADACfgIdleCharDelay

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.16.1.1.2

The SCADA idle character delay.

ipadSCADACfgInputTerminator

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.16.1.1.3

The SCADA input message terminator.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.16.1.1.4

ipadSCADACfgAddDevLst

Appends an entry to the SCADA device list table.

Enumerationr/w

Enumerated Values:

1	other
2	addnew

.1.3.6.1.4.1.321.100.1.16.1.1.5

ipadSCADACfgDeleteDevLst

Deletes an entry in the SCADA device list table.

ipadSCADACfgDataDirection

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.16.1.1.6

Data Direction enables for SCADA configuration.

Enumerationr/w

Enumerated Values:

1	other
2	both
3	output
4	input

.1.3.6.1.4.1.321.100.1.16.1.1.7

ipadSCADACfgProtocol

Configured SCADA Protocol.

Enumerationr/w

Enumerated Values:

1	other
2	async
3	syncVancommHost
4	syncVancommRTU

.1.3.6.1.4.1.321.100.1.16.1.1.8

ipadSCADACfgLoopback

Loopback allows user to loop data to either Network, Serial Port or both.

Enumerationr/w

Enumerated Values:

1	none
2	network
3	port
4	both

.1.3.6.1.4.1.321.100.1.16.1.1.9

ipadSCADAStatsTable

table

.1.3.6.1.4.1.321.100.1.17.1 · 1 row entry · 8 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadSCADAStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadSCADAStatsTable'

The SCADA statistics table.

ipadSCADAStatsTableEntry row .1.3.6.1.4.1.321.100.1.17.1.1

An entry in the SCADA statistics table.

Indexes

ipadSCADAStatsIndex

Column Syntax OID

ipadSCADAStatsIndex

The index for SCADA Statistics Table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.17.1.1.1

ipadSCADAStatsTxChars

The number of chracters transmitted through SCADA port.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.17.1.1.2

ipadSCADAStatsRxChars

The number of chracters received through SCADA port.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.17.1.1.3

ipadSCADAStatsTxMsgs

The number of messages transmitted through SCADA port.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.17.1.1.4

ipadSCADAStatsRxMsgs

The number of messages received through SCADA port.

ipadSCADAStatsRxParityErrors

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.17.1.1.5

The number of parity errors received from SCADA port.

ipadSCADAStatsRxFramingErrors

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.17.1.1.6

The number of framming errors received from SCADA port.

ipadSCADADevLstIndex ipadSCADADevLstDevIndex

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.17.1.1.7

ipadSCADAStatsClear

Writing a value of ipadSCADAStatsClearNow(2) to this field causes all existing stats to be cleared immediately.

Enumerationr/w

Enumerated Values:

1	ipadSCADAStatsClearOther
2	ipadSCADAStatsClearNow

.1.3.6.1.4.1.321.100.1.17.1.1.8

ipadSCADADevLstTable

table

.1.3.6.1.4.1.321.100.1.18.1 · 1 row entry · 4 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadSCADADevLstTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadSCADADevLstTable'

The SCADA device list table.

ipadSCADADevLstTableEntry row .1.3.6.1.4.1.321.100.1.18.1.1

An entry in the SCADA device list table.

Indexes

Column Syntax OID

ipadSCADADevLstIndex

The index for SCADA device list table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.18.1.1.1

ipadSCADADevLstDevIndex

The index of device.

ipadSCADADevLstEndpointName

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.18.1.1.2

The name of the endpoint.

OctetStringr/w

Constraints:
range: 0-11

.1.3.6.1.4.1.321.100.1.18.1.1.3

ipadSCADADevLstEntryStatus

The disabled or dnabled status of the entry.

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	enable

.1.3.6.1.4.1.321.100.1.18.1.1.4

ipadDS0ConfigTable

table

.1.3.6.1.4.1.321.100.1.19.1 · 1 row entry · 11 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadDS0ConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadDS0ConfigTable'

The ipad DS0 Utilization Monitor Config table.

ipadDS0ConfigTableEntry row .1.3.6.1.4.1.321.100.1.19.1.1

An entry in the ipad DS0 Utilization Monitor Config table.

Indexes

ipadDS0ConfigIndex

Column Syntax OID

ipadDS0ConfigIndex

Index into the DS0 Utilization Monitor Config table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.19.1.1.1

ipadDS0ConfigNumberDS0

Number of DS0's monitored by this table entry.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.19.1.1.2

ipadDS0ConfigResetTimer

Number of contiguous seconds a utilization alarm must not
be present before the alarm condition is automatically reset.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.19.1.1.3

ipadDS0ConfigHighUtil

What the user considers a high DS0 utilization for this entry.
Utilization is expressed as a percentage.

ipadDS0ConfigHighUtilThreshold

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.19.1.1.4

Number of seconds a high utilization condition must be
present within 15 minutes before an alarm condition is
declared.

ipadDS0ConfigHighUtilStatus

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.19.1.1.5

Indicates if a high utilization condition exists.

Enumeration

Enumerated Values:

1	other
2	notExist
3	exists

.1.3.6.1.4.1.321.100.1.19.1.1.6

ipadDS0ConfigHighUtilCount

The number of seconds in the past 15 minutes that have
been greater than or equal to the high utilization parameter.
The value is calculated from a sliding window of
15 one-minute buckets.

ipadDS0ConfigHighUtilAlarm

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.19.1.1.7

Indicates if the high utilization alarm threshold is exceeded.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.19.1.1.8

ipadDS0ConfigLowUtil

What the user considers an end-of-day low DS0 utilization
for this entry. Utilization is expressed as a percentage.
When the utilization is set to zero the low utilization
alarm is disabled.

ipadDS0ConfigLowUtilAlarm

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.19.1.1.9

Indicates if the low utilization alarm is declared.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.19.1.1.10

ipadDS0ConfigReset

The set values perform the following actions:
clearAlarms(2) - Clears any active DS0 utilization alarms and counts
clearHistory(3) - Clears DS0 utilization history tables.

Enumerationr/w

Enumerated Values:

1	none
2	clearAlarms
3	clearHistory

.1.3.6.1.4.1.321.100.1.19.1.1.11

ipadDS0Hist24Table

table

.1.3.6.1.4.1.321.100.1.20.1 · 1 row entry · 5 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadDS0Hist24Table

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadDS0Hist24Table'

The ipad DS0 Utilization Monitor 24-Hour History table.

ipadDS0Hist24TableEntry row .1.3.6.1.4.1.321.100.1.20.1.1

An entry in the ipad DS0 Utilization Monitor 24-Hour History table.

Indexes

ipadDS0Hist24Index ipadDS0Hist24HistoricalIndex

Column Syntax OID

ipadDS0Hist24Index

Index into the DS0 Utilization Monitor 24-Hour History table.

ipadDS0Hist24HistoricalIndex

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.20.1.1.1

Historical index into the DS0 Utilization Monitor 24-Hour History table.

Enumeration

Enumerated Values:

1	statSummary
2	statCurrent
3	statPeriod1
4	statPeriod2
5	statPeriod3
6	statPeriod4
7	statPeriod5
8	statPeriod6
9	statPeriod7
10	statPeriod8
11	statPeriod9
12	statPeriod10
13	statPeriod11
14	statPeriod12
15	statPeriod13
16	statPeriod14
17	statPeriod15
18	statPeriod16
19	statPeriod17
20	statPeriod18
21	statPeriod19
22	statPeriod20
23	statPeriod21
24	statPeriod22
25	statPeriod23
26	statPeriod24
27	statPeriod25
28	statPeriod26
29	statPeriod27
30	statPeriod28
31	statPeriod29
32	statPeriod30
33	statPeriod31
34	statPeriod32
35	statPeriod33
36	statPeriod34
37	statPeriod35
38	statPeriod36
39	statPeriod37
40	statPeriod38
41	statPeriod39
42	statPeriod40
43	statPeriod41
44	statPeriod42
45	statPeriod43
46	statPeriod44
47	statPeriod45
48	statPeriod46
49	statPeriod47
50	statPeriod48
51	statPeriod49
52	statPeriod50
53	statPeriod51
54	statPeriod52
55	statPeriod53
56	statPeriod54
57	statPeriod55
58	statPeriod56
59	statPeriod57
60	statPeriod58
61	statPeriod59
62	statPeriod60
63	statPeriod61
64	statPeriod62
65	statPeriod63
66	statPeriod64
67	statPeriod65
68	statPeriod66
69	statPeriod67
70	statPeriod68
71	statPeriod69
72	statPeriod70
73	statPeriod71
74	statPeriod72
75	statPeriod73
76	statPeriod74
77	statPeriod75
78	statPeriod76
79	statPeriod77
80	statPeriod78
81	statPeriod79
82	statPeriod80
83	statPeriod81
84	statPeriod82
85	statPeriod83
86	statPeriod84
87	statPeriod85
88	statPeriod86
89	statPeriod87
90	statPeriod88
91	statPeriod89
92	statPeriod90
93	statPeriod91
94	statPeriod92
95	statPeriod93
96	statPeriod94
97	statPeriod95
98	statPeriod96

.1.3.6.1.4.1.321.100.1.20.1.1.2

ipadDS0Hist24Timestamp

SysUpTime when the utilization interval completed.

ipadDS0Hist24HighUtilSeconds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.321.100.1.20.1.1.3

The number of seconds in the interval that have
been greater than or equal to the high utilization parameter.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.20.1.1.4

ipadDS0Hist24Utilization

The percent of DS0's utilized over the given interval.

ipadDS0Hist30Index ipadDS0Hist30HistoricalIndex

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.20.1.1.5

ipadDS0Hist30Table

table

.1.3.6.1.4.1.321.100.1.21.1 · 1 row entry · 5 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadDS0Hist30Table

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadDS0Hist30Table'

The ipad DS0 Utilization Monitor 30-Day History table.

ipadDS0Hist30TableEntry row .1.3.6.1.4.1.321.100.1.21.1.1

An entry in the ipad DS0 Utilization Monitor 30-Day History table.

Indexes

Column Syntax OID

ipadDS0Hist30Index

Index into the DS0 Utilization Monitor 30-Day History table.

ipadDS0Hist30HistoricalIndex

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.21.1.1.1

Historical index into the DS0 Utilization Monitor 30-Day History table.

Enumeration

Enumerated Values:

1	statSummary
2	statDay1
3	statDay2
4	statDay3
5	statDay4
6	statDay5
7	statDay6
8	statDay7
9	statDay8
10	statDay9
11	statDay10
12	statDay11
13	statDay12
14	statDay13
15	statDay14
16	statDay15
17	statDay16
18	statDay17
19	statDay18
20	statDay19
21	statDay20
22	statDay21
23	statDay22
24	statDay23
25	statDay24
26	statDay25
27	statDay26
28	statDay27
29	statDay28
30	statDay29
31	statDay30

.1.3.6.1.4.1.321.100.1.21.1.1.2

ipadDS0Hist30Timestamp

SysUpTime when the utilization interval completed.

ipadDS0Hist30HighUtilSeconds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.321.100.1.21.1.1.3

The number of seconds in the interval that have
been greater than or equal to the high utilization parameter.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.21.1.1.4

ipadDS0Hist30Utilization

The percent of DS0's utilized over the given interval.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.21.1.1.5

ipadHDLCConfigTable

table

.1.3.6.1.4.1.321.100.1.22.1 · 1 row entry · 19 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadHDLCConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadHDLCConfigTable'

The ipad HDLC Utilization Monitor Config table.

ipadHDLCConfigTableEntry row .1.3.6.1.4.1.321.100.1.22.1.1

An entry in the ipad HDLC Utilization Monitor Config table.

Indexes

ipadHDLCConfigIndex

Column Syntax OID

ipadHDLCConfigIndex

Index into the HDLC Utilization Monitor Config table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.1

ipadHDLCConfigService

Service the HDLC utilization monitor is attached.
0 = Disabled.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.2

ipadHDLCConfigServiceBPS

Service bit rate.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.3

ipadHDLCConfigResetTimer

Number of contiguous seconds a utilization alarm must not
be present before the alarm condition is automatically reset.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.4

ipadHDLCConfigRxHighUtil

What the user considers a high Rx HDLC utilization for this entry.
Utilization is expressed as a percentage.

ipadHDLCConfigRxHighUtilThreshold

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.5

Number of seconds a Rx high utilization condition must be
present within 15 minutes before an alarm condition is
declared.

ipadHDLCConfigRxHighUtilStatus

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.6

Indicates if a Rx high utilization condition exists.

Enumeration

Enumerated Values:

1	other
2	notExist
3	exists

.1.3.6.1.4.1.321.100.1.22.1.1.7

ipadHDLCConfigRxHighUtilCount

The number of seconds in the past 15 minutes that have
been greater than or equal to the Rx high utilization parameter.
The value is calculated from a sliding window of
15 one-minute buckets.

ipadHDLCConfigRxHighUtilAlarm

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.8

Indicates if the Rx high utilization alarm threshold is exceeded.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.22.1.1.9

ipadHDLCConfigRxLowUtil

What the user considers an end-of-day low Rx HDLC utilization
for this entry. Utilization is expressed as a percentage.
When the utilization is set to zero the Rx low utilization
alarm is disabled.

ipadHDLCConfigRxLowUtilAlarm

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.10

Indicates if the Rx low utilization alarm is declared.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.22.1.1.11

ipadHDLCConfigTxHighUtil

What the user considers a high Tx HDLC utilization for this entry.
Utilization is expressed as a percentage.

ipadHDLCConfigTxHighUtilThreshold

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.12

Number of seconds a Tx high utilization condition must be
present within 15 minutes before an alarm condition is
declared.

ipadHDLCConfigTxHighUtilStatus

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.13

Indicates if a Tx high utilization condition exists.

Enumeration

Enumerated Values:

1	other
2	notExist
3	exists

.1.3.6.1.4.1.321.100.1.22.1.1.14

ipadHDLCConfigTxHighUtilCount

The number of seconds in the past 15 minutes that have
been greater than or equal to the Tx high utilization parameter.
The value is calculated from a sliding window of
15 one-minute buckets.

ipadHDLCConfigTxHighUtilAlarm

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.15

Indicates if the Tx high utilization alarm threshold is exceeded.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.22.1.1.16

ipadHDLCConfigTxLowUtil

What the user considers an end-of-day low Tx HDLC utilization
for this entry. Utilization is expressed as a percentage.
When the utilization is set to zero the Tx low utilization
alarm is disabled.

ipadHDLCConfigTxLowUtilAlarm

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.22.1.1.17

Indicates if the Tx low utilization alarm is declared.

Enumeration

Enumerated Values:

1	other
2	noAlarm
3	thresholdExceeded

.1.3.6.1.4.1.321.100.1.22.1.1.18

ipadHDLCConfigReset

The set values perform the following actions:
clearAlarms(2) - Clears any active HDLC utilization alarms and counts
clearHistory(3) - Clears HDLC utilization history tables.

Enumerationr/w

Enumerated Values:

1	none
2	clearAlarms
3	clearHistory

.1.3.6.1.4.1.321.100.1.22.1.1.19

ipadHDLCHist24Table

table

.1.3.6.1.4.1.321.100.1.23.1 · 1 row entry · 7 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadHDLCHist24Table

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadHDLCHist24Table'

The ipad HDLC Utilization Monitor 24-Hour History table.

ipadHDLCHist24TableEntry row .1.3.6.1.4.1.321.100.1.23.1.1

An entry in the ipad HDLC Utilization Monitor 24-Hour History table.

Indexes

ipadHDLCHist24Index ipadHDLCHist24HistoricalIndex

Column Syntax OID

ipadHDLCHist24Index

Index into the HDLC Utilization Monitor 24-Hour History table.

ipadHDLCHist24HistoricalIndex

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.23.1.1.1

Historical index into the HDLC Utilization Monitor 24-Hour History table.

Enumeration

Enumerated Values:

1	statSummary
2	statCurrent
3	statPeriod1
4	statPeriod2
5	statPeriod3
6	statPeriod4
7	statPeriod5
8	statPeriod6
9	statPeriod7
10	statPeriod8
11	statPeriod9
12	statPeriod10
13	statPeriod11
14	statPeriod12
15	statPeriod13
16	statPeriod14
17	statPeriod15
18	statPeriod16
19	statPeriod17
20	statPeriod18
21	statPeriod19
22	statPeriod20
23	statPeriod21
24	statPeriod22
25	statPeriod23
26	statPeriod24
27	statPeriod25
28	statPeriod26
29	statPeriod27
30	statPeriod28
31	statPeriod29
32	statPeriod30
33	statPeriod31
34	statPeriod32
35	statPeriod33
36	statPeriod34
37	statPeriod35
38	statPeriod36
39	statPeriod37
40	statPeriod38
41	statPeriod39
42	statPeriod40
43	statPeriod41
44	statPeriod42
45	statPeriod43
46	statPeriod44
47	statPeriod45
48	statPeriod46
49	statPeriod47
50	statPeriod48
51	statPeriod49
52	statPeriod50
53	statPeriod51
54	statPeriod52
55	statPeriod53
56	statPeriod54
57	statPeriod55
58	statPeriod56
59	statPeriod57
60	statPeriod58
61	statPeriod59
62	statPeriod60
63	statPeriod61
64	statPeriod62
65	statPeriod63
66	statPeriod64
67	statPeriod65
68	statPeriod66
69	statPeriod67
70	statPeriod68
71	statPeriod69
72	statPeriod70
73	statPeriod71
74	statPeriod72
75	statPeriod73
76	statPeriod74
77	statPeriod75
78	statPeriod76
79	statPeriod77
80	statPeriod78
81	statPeriod79
82	statPeriod80
83	statPeriod81
84	statPeriod82
85	statPeriod83
86	statPeriod84
87	statPeriod85
88	statPeriod86
89	statPeriod87
90	statPeriod88
91	statPeriod89
92	statPeriod90
93	statPeriod91
94	statPeriod92
95	statPeriod93
96	statPeriod94
97	statPeriod95
98	statPeriod96

.1.3.6.1.4.1.321.100.1.23.1.1.2

ipadHDLCHist24Timestamp

SysUpTime when the utilization interval completed.

ipadHDLCHist24RxHighUtilSeconds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.321.100.1.23.1.1.3

The number of seconds in the interval that have been greater
than or equal to the Rx high utilization parameter.

ipadHDLCHist24RxUtilization

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.23.1.1.4

The percent of Rx HDLC bandwidth utilized over the given interval.

ipadHDLCHist24TxHighUtilSeconds

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.23.1.1.5

The number of seconds in the interval that have been greater
than or equal to the Tx high utilization parameter.

ipadHDLCHist24TxUtilization

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.23.1.1.6

The percent of Tx HDLC bandwidth utilized over the given interval.

ipadHDLCHist30Index ipadHDLCHist30HistoricalIndex

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.23.1.1.7

ipadHDLCHist30Table

table

.1.3.6.1.4.1.321.100.1.24.1 · 1 row entry · 7 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadHDLCHist30Table

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadHDLCHist30Table'

The ipad HDLC Utilization Monitor 30-Day History table.

ipadHDLCHist30TableEntry row .1.3.6.1.4.1.321.100.1.24.1.1

An entry in the ipad HDLC Utilization Monitor 30-Day History table.

Indexes

Column Syntax OID

ipadHDLCHist30Index

Index into the HDLC Utilization Monitor 30-Day History table.

ipadHDLCHist30HistoricalIndex

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.24.1.1.1

Historical index into the HDLC Utilization Monitor 30-Day History table.

Enumeration

Enumerated Values:

1	statSummary
2	statDay1
3	statDay2
4	statDay3
5	statDay4
6	statDay5
7	statDay6
8	statDay7
9	statDay8
10	statDay9
11	statDay10
12	statDay11
13	statDay12
14	statDay13
15	statDay14
16	statDay15
17	statDay16
18	statDay17
19	statDay18
20	statDay19
21	statDay20
22	statDay21
23	statDay22
24	statDay23
25	statDay24
26	statDay25
27	statDay26
28	statDay27
29	statDay28
30	statDay29
31	statDay30

.1.3.6.1.4.1.321.100.1.24.1.1.2

ipadHDLCHist30Timestamp

SysUpTime when the utilization interval completed.

ipadHDLCHist30RxHighUtilSeconds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.321.100.1.24.1.1.3

The number of seconds in the interval that have been greater
than or equal to the Rx high utilization parameter.

ipadHDLCHist30RxUtilization

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.24.1.1.4

The percent of Rx HDLC bandwidth utilized over the given interval.

ipadHDLCHist30TxHighUtilSeconds

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.24.1.1.5

The number of seconds in the interval that have been greater
than or equal to the Tx high utilization parameter.

ipadHDLCHist30TxUtilization

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.24.1.1.6

The percent of Tx HDLC bandwidth utilized over the given interval.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.24.1.1.7

ipadAutoLearnDS0Table

table

.1.3.6.1.4.1.321.100.1.31.1 · 1 row entry · 4 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadAutoLearnDS0Table

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadAutoLearnDS0Table'

The ipad Auto Learn DS0 Config table.

ipadAutoLearnDS0TableEntry row .1.3.6.1.4.1.321.100.1.31.1.1

An entry in the ipad Auto Learn DS0 Config table.

Indexes

ipadAutoLearnDS0Index

Column Syntax OID

ipadAutoLearnDS0Index

The MIB-II ifIndex into the Auto Learn DS0 Config table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.31.1.1.1

ipadAutoLearnDS0Boot

Select when to automatically learn DS0 assignments:
disable - Do not automatically learn DS0s
enable - Learn on boot
carrierDown - Learn on boot and while the ifIndex carrier is down
serviceDown - Learn on boot and whil…

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	enable
4	carrierDown
5	serviceDown

.1.3.6.1.4.1.321.100.1.31.1.1.2

ipadAutoLearnDS0Rate

Select the rate of the learned DS0's.

Enumerationr/w

Enumerated Values:

1	other
2	auto
3	learnAs56K
4	learnAs64K
5	learnAsVoice

.1.3.6.1.4.1.321.100.1.31.1.1.3

ipadAutoLearnDS0Command

The set values perform the following actions:
learnNow(2) - Attempt to learn the active DS0's now.

Enumerationr/w

Enumerated Values:

1	none
2	learnNow

.1.3.6.1.4.1.321.100.1.31.1.1.4

ipadUnitAccessTable

table

.1.3.6.1.4.1.321.100.1.32.1 · 1 row entry · 3 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadUnitAccessTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadUnitAccessTable'

The ipad Unit Access table.

ipadUnitAccessTableEntry row .1.3.6.1.4.1.321.100.1.32.1.1

An entry in the ipad Unit Access table.

Indexes

ipadAutoLearnDS0Index

Column	Syntax	OID
ipadUnitAccessIndex The MIB-II Index into the Unit Access table.	Integer32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.321.100.1.32.1.1.1`
ipadUnitAccessIpa IP Address of Source to allow Unit Access.	SNMPv2-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.321.100.1.32.1.1.2`
ipadUnitAccessMask Mask of Source to allow Unit Access.	SNMPv2-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.321.100.1.32.1.1.3`

ipadDLMTable

table

.1.3.6.1.4.1.321.100.1.34.2 · 1 row entry · 7 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadDLMTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadDLMTable'

The ipad Data Line Monitor configuration table.

ipadDLMTableEntry row .1.3.6.1.4.1.321.100.1.34.2.1

An entry in the ipad DLM config table.

Indexes

ipadDLMServiceIndex

Column Syntax OID

ipadDLMServiceIndex

The service index into the DLM table.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.34.2.1.1

ipadDLMEnable

Enable/Disable the DLM on the specified service.

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	enable

.1.3.6.1.4.1.321.100.1.34.2.1.2

ipadDLMTxRxFilter

Allows the user to capture only received, transmit, or both.

Enumerationr/w

Enumerated Values:

1	other
2	all
3	transmitOnly
4	receiveOnly

.1.3.6.1.4.1.321.100.1.34.2.1.3

ipadDLMPatternEnable

Enable/Disable the search for a specific pattern.

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	enable

.1.3.6.1.4.1.321.100.1.34.2.1.4

ipadDLMPattern

The pattern to search for in the captured packets.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.34.2.1.5

ipadDLMPatternMask

The mask to use with ipadDLMPattern to search for in
the captured packets.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.34.2.1.6

ipadDLMPatternOffset

The offset into the packet to search for the pattern.

Integer32r/w

Constraints:
range: 0-32

.1.3.6.1.4.1.321.100.1.34.2.1.7

ipadDLMPacketTable

table

.1.3.6.1.4.1.321.100.1.34.3 · 1 row entry · 6 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk ipadDLMPacketTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IPADv2-MIB' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IPADv2-MIB::ipadDLMPacketTable'

The ipad Data Link Monitor packet table.

ipadDLMPacketTableEntry row .1.3.6.1.4.1.321.100.1.34.3.1

An entry in the ipad DLM packet table.

Indexes

ipadDLMPacketIndex

Column Syntax OID

ipadDLMPacketIndex

The service index into the DLM table.

ipadDLMPacketServiceIndex

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.34.3.1.1

The service index the packet was captured on.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.321.100.1.34.3.1.2

ipadDLMPacketTimestamp

The time that the packet was captured.

ipadDLMPacketDataDirection

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.321.100.1.34.3.1.3

The direction the data was goin in respect to the interface.

Enumeration

Enumerated Values:

1	other
2	transmit
3	receive

.1.3.6.1.4.1.321.100.1.34.3.1.4

ipadDLMPacketSize

The size of the captured packet.