ipadDLCItxExCIRAlarm
IPADv2-MIB ·
.1.3.6.1.4.1.321.100.1.4.1.1.19
Object
column
Enumeration
Reports if the Tx over CIR threshold has been exceeded.
Context
- MIB
- IPADv2-MIB
- OID
.1.3.6.1.4.1.321.100.1.4.1.1.19- Type
- column
- Access
- readonly
- Status
- current
- Parent
- ipadDLCITableEntry
- Table
- ipadDLCITable
- Siblings
- 40
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | other |
2 | noAlarm |
3 | thresholdExceeded |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ipadDLCIservice An index into the ipad service table. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.1 |
| ipadDLCIpropOffset When the encapsulation is proprietary, this is the number of bytes
after the frame relay header to look for the specified protocol
decode. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.10 |
| ipadDLCIinBand Determines if frames on this DLCI will be parsed to look
for management frames destined for the unit itself. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.11 |
| ipadDLCICIR Default committed information rate in bits per second. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.12 |
| ipadDLCIBe Default excess burst rate in bits per second. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.13 |
| ipadDLCIminBC If the corresponding interface is configured to enable
congestion management, the minimum transfer rate at which
the unit will throttle back offering data to the network. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.14 |
| ipadDLCIrxMon Determines if the SLA parameters will be monitored for received
frames. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.15 |
| ipadDLCIdEctrl Determines if the Rx monitor will set the DE bit on all frames
received in excess of the CIR before they are switched to their
destination port. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.16 |
| ipadDLCIenableDelay Enable or disable delay. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.17 |
| ipadDLCItxExCIRThreshold Sets the Tx over CIR alarm threshold. This threshold
is the number of bits per second in excess of CIR. Setting
this field to 0 disables the alarm. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.18 |
| ipadDLCInumber The DLCI number for this entry. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.2 |
| ipadDLCItxExBeThreshold Sets the Tx over Be alarm threshold. This threshold is the
number of bits per second in excess of Be. Setting this
field to 0 disables the alarm. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.20 |
| ipadDLCItxExBeAlarm Reports if the Tx over Be threshold has been exceeded. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.21 |
| ipadDLCIrxCongThreshold Sets the Rx congestion alarm threshold. This threshold
is the number of frames received with BECN/FECN. Setting
this field to 0 disables the alarm. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.22 |
| ipadDLCIrxCongAlarm Reports if the Rx congestion threshold has been exceeded. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.23 |
| ipadDLCIrxBECNinCIR Reports if BECN has been received within CIR. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.24 |
| ipadDLCIUASThreshold Sets the UAS (unavailable seconds) alarm threshold. This
threshold is the number of seconds passed that the DLCI is
unavailable. Setting this field to 0 disables the alarm. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.25 |
| ipadDLCIUASAlarm Reports if the UAS threshold has been exceeded. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.26 |
| ipadDLCIAlarmReset This is used to clear the current alarm counts. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.27 |
| ipadDLCIRoundTripDelaySize Specifies the packet size in octets used to calculate
round trip delay. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.28 |
| ipadDLCIRoundTripDelayRate Specifies the packet rate in seconds used to calculate
round trip delay. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.29 |
| ipadDLCIactive Specifies if the DLCI is active. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.3 |
| ipadDLCIRemoteFramesOfferedWithinCIR Count of frames sent within CIR from the remote end of the DLCI. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.30 |
| ipadDLCIRemoteFramesOfferedWithinBE Count of frames sent within BE, but over CIR, from the remote end of the DLCI. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.31 |
| ipadDLCIFramesReceived Count of frames received by the local device on this DLCI. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.32 |
| ipadDLCIRemoteDataOfferedWithinCIR Count of data octets sent within CIR from the remote end of the DLCI. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.33 |
| ipadDLCIRemoteDataOfferedWithinBE Count of data octets sent within BE, but over CIR, from the remote
end of the DLCI. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.34 |
| ipadDLCIDataReceived Count of data octets received by the local device on this DLCI. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.35 |
| ipadDLCIRemoteIPAddress The IP Address of the device on the remote end of this DLCI. This information
is only valid when the remote device supports Verilink's proprietary message
exchange. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.321.100.1.4.1.1.36 |
| ipadDLCICompressionStatus This is the current status of the compression engine for this DLCI.
disabled(2) indicates that the compression engine is disabled.
enabledAndNegotiated(3) indicates that compres… | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.37 |
| ipadDLCICompressionTxOctetsIn This is a rolling counter of the number of octets given to the compression
engine. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.38 |
| ipadDLCICompressionTxOctetsOut This is a rolling counter of the number of octets output from the compression
engine. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.39 |
| ipadDLCIcongestion Specifies if the dlci is receiving frames
with FECN or BECN bit set. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.4 |
| ipadDLCICompressionRxOctetsIn This is a rolling counter of the number of octets given to the compression
engine. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.40 |
| ipadDLCICompressionRxOctetsOut This is a rolling counter of the number of octets given to the compression
engine. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.41 |
| ipadDLCIremote Remote DLCI number. | column | Integer32 | .1.3.6.1.4.1.321.100.1.4.1.1.5 |
| ipadDLCIremoteUnit Name of the remote DLCI. | column | OctetString | .1.3.6.1.4.1.321.100.1.4.1.1.6 |
| ipadDLCIremoteEquipActive Reports if the equipment attached to the
remote unit is active. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.7 |
| ipadDLCIencapsulation Type of protocol encapsulation used on this DLCI. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.8 |
| ipadDLCIproprietary When the encapsulation is proprietary, the traffic type must be
configured to gather protocol specific statistics. | column | Enumeration | .1.3.6.1.4.1.321.100.1.4.1.1.9 |