IBM-OSA-MIB Table View

ibmOSAExpChannelProcCodeLevel

Column Syntax OID

ibmOSAExpChannelNumber

The CHPID corresponding to this ifIndex.

OctetString

Constraints:
range: 2-2

.1.3.6.1.4.1.2.6.188.1.1.1.1

ibmOSAExpChannelType

The type of channel for this interface.
OSA Direct Express has a value of 17.

Enumeration

Enumerated Values:

17	osaDirectExpress

.1.3.6.1.4.1.2.6.188.1.1.1.2

ibmOSAExpChannelHdwLevel

Hardware model of the channel.
The value oasExp150(2) indicates a hardware level of 1.50.
The value oasExp175(3) indicates a hardware level of 1.75.

Enumeration

Enumerated Values:

1	unknown
2	osaExp150
3	osaExp175

.1.3.6.1.4.1.2.6.188.1.1.1.3

ibmOSAExpChannelSubType

Indicates the type of OSA feature present.

Enumeration

Enumerated Values:

1	unknown
65	gigabitEthernet
81	fastEthernet
82	tokenRing
2304	atmEmulatedEthernet

.1.3.6.1.4.1.2.6.188.1.1.1.4

ibmOSAExpChannelShared

An OSA-Express feature can be shared across multiple LPs.
This object indicates if this feature is currently being
shared between LPs

Enumeration

Enumerated Values:

0	notShared
1	shared

.1.3.6.1.4.1.2.6.188.1.1.1.5

ibmOSAExpChannelNodeDesc

This is the Node Descriptor of the OSA feature.
It represents the ND obtained from the Channel Subsystem.

Bits Name Flag is first byte
char(1) Validity Valid - always '20'x
char(1) Re…

OctetString

Constraints:
range: 32-32

.1.3.6.1.4.1.2.6.188.1.1.1.6

This is the firmware (or micro code level) of the OSA
feature. For example, OSA code level 05.6A would be
represented as 0x056A.

OctetString

Constraints:
range: 2-2

.1.3.6.1.4.1.2.6.188.1.1.1.8

ibmOSAExpChannelPCIBusUtil1Min

The average, over a 1 minute interval, of the percentage
of time that the PCI bus was utilized to transfer data.
It does not include idle time or time used by
routine maintenance tasks. The range for this value
is from…

Integer32

Constraints:
range: 0-100

.1.3.6.1.4.1.2.6.188.1.1.1.9

ibmOSAExpChannelProcUtil1Min

The average, over a 1 minute interval, of the percentage
of time that the CHPID Processor was utilized to transfer
data. It does not include idle time or time used by
routine maintenance tasks. The range for this valu…

Integer32

Constraints:
range: 0-100

.1.3.6.1.4.1.2.6.188.1.1.1.10

ibmOSAExpChannelPCIBusUtil5Min

The average, over a 5 minute interval, of the percentage
of time that the PCI bus was utilized to transfer data.
It does not include idle time or time used by
routine maintenance tasks. The range for this value
is from…

Integer32

Constraints:
range: 0-100

.1.3.6.1.4.1.2.6.188.1.1.1.11

ibmOSAExpChannelProcUtil5Min

The average, over a 5 minute interval, of the percentage
of time that the CHPID Processor was utilized to transfer
data. It does not include idle time or time used by
routine maintenance tasks. The range for this valu…

Integer32

Constraints:
range: 0-100

.1.3.6.1.4.1.2.6.188.1.1.1.12

ibmOSAExpChannelPCIBusUtilHour

The average, over an hour interval, of the percentage
of time that the PCI bus was utilized to transfer data.
It does not include idle time or time used by
routine maintenance tasks.

Integer32

Constraints:
range: 0-100

.1.3.6.1.4.1.2.6.188.1.1.1.13

ibmOSAExpChannelProcUtilHour

The average, over an hour interval, of the percentage
of time that the CHPID Processor was utilized to transfer
data. It does not include idle time or time used by
routine maintenance tasks. The range for this value
i…

Integer32

Constraints:
range: 0-100

.1.3.6.1.4.1.2.6.188.1.1.1.14

ibmOSAExpPerfTable

table

.1.3.6.1.4.1.2.6.188.1.2 · 1 row entry · 16 columns

Open in standard view

Uses the ibm variant from /opt/observium/mibs/ibm.

Command help

Walk ibmOSAExpPerfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IBM-OSA-MIB' -M '/opt/observium/mibs/ibm:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IBM-OSA-MIB::ibmOSAExpPerfTable'

This table provides performance information for each
Logical Partition (LP) the OSA can connect to.

ibmOSAExpPerfEntry row .1.3.6.1.4.1.2.6.188.1.2.1

Definition of a single entry for a single LP
in the ibmOSAExpPerfTable.
Indexed by the ifIndex of the corresponding Device interface.

Indexes

Column	Syntax	OID
ibmOSAExpPerfDataLP0 The performance data on this OSA for partition 0. The 40 bytes of hex data that are returned are decoded as follows: Offset Bytes Field Meaning 0 4 LP Number 4 4 Processor Util 1 M…	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.1`
ibmOSAExpPerfDataLP1 The performance data on this OSA for partition 1. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.2`
ibmOSAExpPerfDataLP2 The performance data on this OSA for partition 2. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.3`
ibmOSAExpPerfDataLP3 The performance data on this OSA for partition 3. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.4`
ibmOSAExpPerfDataLP4 The performance data on this OSA for partition 4. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.5`
ibmOSAExpPerfDataLP5 The performance data on this OSA for partition 5. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.6`
ibmOSAExpPerfDataLP6 The performance data on this OSA for partition 6. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.7`
ibmOSAExpPerfDataLP7 The performance data on this OSA for partition 7. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.8`
ibmOSAExpPerfDataLP8 The performance data on this OSA for partition 8. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.9`
ibmOSAExpPerfDataLP9 The performance data on this OSA for partition 9. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.10`
ibmOSAExpPerfDataLP10 The performance data on this OSA for partition 10. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.11`
ibmOSAExpPerfDataLP11 The performance data on this OSA for partition 11. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.12`
ibmOSAExpPerfDataLP12 The performance data on this OSA for partition 12. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.13`
ibmOSAExpPerfDataLP13 The performance data on this OSA for partition 13. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.14`
ibmOSAExpPerfDataLP14 The performance data on this OSA for partition 14. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.15`
ibmOSAExpPerfDataLP15 The performance data on this OSA for partition 15. The 40 bytes of hex data that are returned are decoded the same as for partition 0.	OctetString Constraints: `range: 40-40`	`.1.3.6.1.4.1.2.6.188.1.2.1.16`

ibmOSAExpPETable

table

.1.3.6.1.4.1.2.6.188.1.3 · 1 row entry · 6 columns

Open in standard view

Uses the ibm variant from /opt/observium/mibs/ibm.

Command help

Walk ibmOSAExpPETable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IBM-OSA-MIB' -M '/opt/observium/mibs/ibm:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IBM-OSA-MIB::ibmOSAExpPETable'

This table provides PE information to help IBM diagnose any
OSA problems.

ibmOSAExpPEEntry row .1.3.6.1.4.1.2.6.188.1.3.1

Definition of a single entry in the ibmOSAExpPETable.
Indexed by the ifIndex of the corresponding Device interface

Indexes

Column	Syntax	OID
ibmOSAExpPEMaxSizeArpCache The maximum size of the OSA ARP Cache	Integer32 Constraints: `range: 0-214783647`	`.1.3.6.1.4.1.2.6.188.1.3.1.1`
ibmOSAExpPEArpPendingEntries This is the number of Pending entries in the ARP cache.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.2.6.188.1.3.1.2`
ibmOSAExpPEArpActiveEntries This the number of active ARP entries.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.2.6.188.1.3.1.3`
ibmOSAExpPEIPEntries The number of IP addresses known to the OSA For OSD chpids, this is the maximum # of IP addresses that are: - home ip addresses (Version 4 and Version 6) - remote ip addresses in the arp cache (Version 4 only) - multica…	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.2.6.188.1.3.1.4`
ibmOSAExpPEMulticastEntries This is the number of IP multicast addresses currently on the OSA	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.2.6.188.1.3.1.5`
ibmOSAExpPEMulticastData This contains information on the multicast entries that are currently on the OSA. These are in a format that is for IBM use only	OctetString Constraints: `range: 3360-3360`	`.1.3.6.1.4.1.2.6.188.1.3.1.6`

ibmOSAExpEthPortTable

table

.1.3.6.1.4.1.2.6.188.1.4 · 1 row entry · 18 columns

Open in standard view

Uses the ibm variant from /opt/observium/mibs/ibm.

Command help

Walk ibmOSAExpEthPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IBM-OSA-MIB' -M '/opt/observium/mibs/ibm:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IBM-OSA-MIB::ibmOSAExpEthPortTable'

This table represents the data associated with a port on an
OSA-Express Gigabit or Fast Ethernet OSA.

ibmOSAExpEthPortEntry row .1.3.6.1.4.1.2.6.188.1.4.1

Definition of a single entry in the ibmOSAExpEthPortTable.
Indexed by the ifIndex of the corresponding Device interface.

Indexes

ibmOsaExpEthLanTrafficState

Column Syntax OID

ibmOsaExpEthPortNumber

The physical port number for this port.

Integer32

Constraints:
range: 0-3

.1.3.6.1.4.1.2.6.188.1.4.1.1

ibmOsaExpEthPortType

The physical port type.

Enumeration

Enumerated Values:

65	gigabitEthernet
81	fastEthernet

.1.3.6.1.4.1.2.6.188.1.4.1.2

The LAN state value ranges from 0 to 8. A value of 5,
disabled is further explained in object
ibmOsaExpEthDisabledStatus.

Enumeration

Enumerated Values:

0	undefined
1	unavailable
2	enabling
3	disabling
4	enabled
5	disabled
6	linkMonitor
7	definitionError
8	configuredOffline

.1.3.6.1.4.1.2.6.188.1.4.1.3

ibmOsaExpEthServiceMode

This object indicates if the processor is in service mode
or not.

Enumeration

Enumerated Values:

0	notInServiceMode
1	inServiceMode

.1.3.6.1.4.1.2.6.188.1.4.1.4

ibmOsaExpEthDisabledStatus

When the value of ibmOsaExpEthLanTrafficState is
NOT disabled, the value of this object will be zero.

When the value of ibmOsaExpEthLanTrafficState is
disabled(5), this object explains the reason for the
…

Bits

Enumerated Values:

0	reserved0
1	internalPortFailure
2	reserved2
3	reserved3
4	reserved4
5	reserved5
6	portTemporarilyDisabled
7	reserved7
8	reserved8
9	serviceProcessorRequest
10	networkRequest
11	osasfRequest
12	configurationChange
13	linkFailureThresholdExceeded
14	reserved14
15	reserved15

.1.3.6.1.4.1.2.6.188.1.4.1.5

ibmOsaExpEthConfigName

This is the name of the configuration that is on the OSA.
It is set using OSA/SF. It is not used by OSA

OctetString

Constraints:
range: 0-34

.1.3.6.1.4.1.2.6.188.1.4.1.6

ibmOsaExpEthConfigSpeedMode

The configured port speed. This field shows the speed
that was configured by the user for the OSA-Express
Fast Ethernet feature.
It is not used by OSA-Express Gigabit features
and will return -1 (FFFF)

Megabits per secondEnumeration

Enumerated Values:

-1	notValidGigabit
0	autoNegotiate
1	tenMbHalfDuplex
2	tenMbFullDuplex
3	oneHundredMbHalfDuplex
4	oneHundredMbFullDuplex
6	oneThousandMbFullDuplex

.1.3.6.1.4.1.2.6.188.1.4.1.7

ibmOsaExpEthActiveSpeedMode

The actual speed and mode the OSA is running in

Megabits per secondEnumeration

Enumerated Values:

0	unknown
1	tenMbHalfDuplex
2	tenMbFullDuplex
3	oneHundredMbHalfDuplex
4	oneHundredMbFullDuplex
6	oneThousandMbFullDuplex

.1.3.6.1.4.1.2.6.188.1.4.1.8

ibmOsaExpEthMacAddrActive

A 6 byte OCTET STRING which contains the current
MAC address in use on the adapter.
The values are in canonical format.

OctetString

Constraints:
range: 6-6

.1.3.6.1.4.1.2.6.188.1.4.1.9

ibmOsaExpEthMacAddrBurntIn

A 6 byte OCTET STRING which contains the burned in
MAC address on the OSA.
The values are in canonical format.

OctetString

Constraints:
range: 6-6

.1.3.6.1.4.1.2.6.188.1.4.1.10

ibmOsaExpEthUserData

Data set by the user. It is ignored by the OSA.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.2.6.188.1.4.1.11

ibmOsaExpEthOutPackets

This is the number of packets that have been transmitted
by the OSA since the last time the OSA port was reset

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.4.1.12

ibmOsaExpEthInPackets

This is the number of packets that have been received
by the OSA since the last time the OSA port was reset

ibmOsaExpEthInGroupFrames

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.4.1.13

This is the number of multicast frames that have been
received by the OSA.

ibmOsaExpEthInBroadcastFrames

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.4.1.14

This is the number of broadcast frames that have been
received by the OSA.

ibmOsaExpEthInUnknownIPFrames

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.4.1.15

ibmOsaExpEthPortName

Name of the port as used by TCP/IP

OctetString

Constraints:
range: 0-8

.1.3.6.1.4.1.2.6.188.1.4.1.16

This is the number of non-IP received frames

ibmOsaExpEthGroupAddrTable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.4.1.17

This field contains the active Group Addresses.
An individual Group Address is 6 bytes long with an
additional 2 bytes of padding. There are 32 group
addresses.

OctetString

Constraints:
range: 256-256

.1.3.6.1.4.1.2.6.188.1.4.1.18

ibmOSAExpTRPortTable

table

.1.3.6.1.4.1.2.6.188.1.5 · 1 row entry · 41 columns

Open in standard view

Uses the ibm variant from /opt/observium/mibs/ibm.

Command help

Walk ibmOSAExpTRPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IBM-OSA-MIB' -M '/opt/observium/mibs/ibm:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IBM-OSA-MIB::ibmOSAExpTRPortTable'

This table represents the data associated with a port on an
OSA-Express token ring feature.

ibmOSAExpTRPortEntry row .1.3.6.1.4.1.2.6.188.1.5.1

Definition of a single entry in the ibmOSAExpTRPortTable.
Indexed by the ifIndex of the corresponding Device interface.

Indexes

ibmOsaExpTRLanTrafficState

Column Syntax OID

ibmOsaExpTRPortNumber

The physical port number for this port.

Integer32

Constraints:
range: 0-3

.1.3.6.1.4.1.2.6.188.1.5.1.1

ibmOsaExpTRPortType

The physical port type.

Enumeration

Enumerated Values:

tokenring

.1.3.6.1.4.1.2.6.188.1.5.1.2

The LAN state value ranges from 0 to 8. A value of 5,
disabled is further explained in object
ibmOsaExpTRDisabledStatus

Enumeration

Enumerated Values:

0	undefined
1	unavailable
2	enabling
3	disabling
4	enabled
5	disabled
6	linkMonitor
7	definitionError
8	configuredOffline

.1.3.6.1.4.1.2.6.188.1.5.1.3

ibmOsaExpTRServiceMode

This object indicates if the processor is in service mode
or not.

Enumeration

Enumerated Values:

0	notInServiceMode
1	inServiceMode

.1.3.6.1.4.1.2.6.188.1.5.1.4

ibmOsaExpTRDisabledStatus

When the value of ibmOsaExpTRLanTrafficState is
NOT disabled, the value of this object will be zero.

When the value of ibmOsaExpTRLanTrafficState is
disabled(5), this object explains the reason for the
d…

Bits

Enumerated Values:

0	reserved0
1	internalPortFailure
2	reserved2
3	reserved3
4	reserved4
5	reserved5
6	portTemporarilyDisabled
7	reserved7
8	reserved8
9	serviceProcessorRequest
10	networkRequest
11	osasfRequest
12	configurationChange
13	linkFailureThresholdExceeded
14	reserved14
15	reserved15

.1.3.6.1.4.1.2.6.188.1.5.1.5

ibmOsaExpTRConfigName

This is the name of the configuration that is on the OSA.
It is set using OSA/SF. It is not used by OSA

OctetString

Constraints:
range: 0-34

.1.3.6.1.4.1.2.6.188.1.5.1.6

ibmOsaExpTRMacAddrActive

A 6 byte OCTET STRING which contains the current
MAC address in use on the OSA.

OctetString

Constraints:
range: 6-6

.1.3.6.1.4.1.2.6.188.1.5.1.7

ibmOsaExpTRMacAddrBurntIn

A 6 byte OCTET STRING which contains the burned in
MAC address on the OSA

OctetString

Constraints:
range: 6-6

.1.3.6.1.4.1.2.6.188.1.5.1.8

ibmOsaExpTRConfigSpeedMode

The configured port speed. This field shows the speed
that was configured by the user for the OSA-Express
Token Ring feature.

Megabits per secondEnumeration

Enumerated Values:

0	autoNegotiate
1	fourMbHalfDuplex
2	fourMbFullDuplex
3	sixteenMbHalfDuplex
4	sixteenMbFullDuplex
6	oneHundredMbFullDuplex

.1.3.6.1.4.1.2.6.188.1.5.1.9

ibmOsaExpTRActiveSpeedMode

The actual speed and mode the OSA is running in

Megabits per secondEnumeration

Enumerated Values:

0	unknown
1	fourMbHalfDuplex
2	fourMbFullDuplex
3	sixteenMbHalfDuplex
4	sixteenMbFullDuplex
6	oneHundredMbFullDuplex

.1.3.6.1.4.1.2.6.188.1.5.1.10

ibmOsaExpTRUserData

Data set by the user. It is ignored by the OSA.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.2.6.188.1.5.1.11

ibmOsaExpTRPortName

Name of the port as used by TCP/IP

OctetString

Constraints:
range: 0-8

.1.3.6.1.4.1.2.6.188.1.5.1.12

ibmOsaExpTRGroupAddrTable

This field contains the active Group Addresses.
An individual Group Address is 6 bytes long with an
additional 2 bytes of padding.

OctetString

Constraints:
range: 256-256

.1.3.6.1.4.1.2.6.188.1.5.1.13

ibmOsaExpTRFunctionalAddr

A 4 byte OCTET STRING which contains the OSA-Express's
functional address.

OctetString

Constraints:
range: 4-4

.1.3.6.1.4.1.2.6.188.1.5.1.14

ibmOsaExpTRRingStatus

The current interface status which can be used to diagnose
fluctuating problems that can occur on token rings after a
station has successfully been added to the ring.
Before an open is completed, this object has the val…

Bits

Enumerated Values:

0	reserved0
1	reserved1
2	reserved2
3	reserved3
4	reserved4
5	reserved5
6	reserved6
7	reserved7
8	reserved8
9	reserved9
10	reserved10
11	reserved11
12	reserved12
13	reserved13
14	noStatusOpenNotCompleted
15	reserved15
16	signalLoss
17	hardError
18	softError
19	reserved19
20	lobeWireFault
21	autoRemovalError
22	fdxProtocol
23	removeReceived
24	counterOverflow
25	singleStation
26	ringRecovery
27	sRCounterOverflow
28	reserved29
29	openInFDXmode
30	fourMbFullDuplex
31	fourMbHalfDuplex

.1.3.6.1.4.1.2.6.188.1.5.1.15

ibmOsaExpTRAllowAccessPriority

This field contains the maximum token priority
the ring station defined by this entry in the
table is permitted to transmit.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.2.6.188.1.5.1.16

ibmOsaExpTREarlyTokenRelease

Indicates if the ring station supports early token release.
Only valid when port is running in 16Mb half duplex mode.
Otherwise it is always set to false (1)

Enumeration

Enumerated Values:

0	true
1	false

.1.3.6.1.4.1.2.6.188.1.5.1.17

ibmOsaExpTRBeaconingAddress

This field contains the node address of the NAUN as
reported in the most recently received Beacon MAC frame.
This field is valid when ibmOsaExpTRRingOpenStatus is
set to beaconing. Otherwise it is ignored

OctetString

Constraints:
range: 6-6

.1.3.6.1.4.1.2.6.188.1.5.1.18

ibmOsaExpTRUpstreamNeighbor

The MAC-address of the up stream neighbor station in
the ring (NAUN).

OctetString

Constraints:
range: 6-6

.1.3.6.1.4.1.2.6.188.1.5.1.19

ibmOsaExpTRRingState

The current interface state with respect
to entering or leaving the ring.

Enumeration

Enumerated Values:

1	opened
2	closed
3	opening
4	closing
5	openFailure
6	ringFailure

.1.3.6.1.4.1.2.6.188.1.5.1.20

ibmOsaExpTRRingOpenStatus

This object indicates the success, or the reason for failure
of the station's most recent attempt to enter the ring.

Enumeration

Enumerated Values:

1	noOpen
2	badParameter
3	lobeFailed
4	signalLoss
5	insertionTimeout
6	ringFailed
7	beaconing
8	duplicateMAC
9	requestFailed
10	removeReceived
11	open
12	sARecFrameNotEqualNAUNs
13	claimTokenRec
14	ringPurgeFramRec
15	activeMonPresRec
16	standbyMonPresRec
17	accessProtocolDenied
18	fDXInsDeniedDACfailOnOpen
19	fDXInsDeniedDACfailOnBeaconTest
20	beaconBeforeOpen
21	insertTimerExpDuringDAC
22	insertTimerExpDuringBeaconTest
23	lobeMedizTestFailure
24	heartbeatFailBeforeOpenCompleted
25	heartbeatFailDuringBeaconTest
26	recBeaconFrameWithInvalidSA

.1.3.6.1.4.1.2.6.188.1.5.1.21

ibmOsaExpTRPacketsTransmitted

This field contains the count of the total number of packets
transmitted from this port since the OSA port was reset

ibmOsaExpTRPacketsReceived

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.22

This field contains the count of the total number of
packets received by this port since the OSA port was reset

ibmOsaExpTRLineErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.23

This counter is incremented when a frame or token is
copied or repeated by a station, the E bit is zero in the
frame or token and one of the following conditions exists:
1) there is a non-data bit (J or K bit) between t…

ibmOsaExpTRBurstErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.24

This counter is incremented when a station detects the
absence of transitions for five half-bit timers
(burst-five error).

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.25

ibmOsaExpTRACErrorCount

This counter is incremented when a station
receives an AMP or SMP frame in which A is
equal to C is equal to 0, and then receives
another SMP frame with A is equal to C is
equal to 0 without first receiving an AMP
frame…

ibmOsaExpTRAbortTransErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.26

This counter is incremented when a station
transmits an abort delimiter while transmitting.

ibmOsaExpTRInternalErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.27

This counter is incremented when a station
recognizes an internal error.

ibmOsaExpTRLostFrameErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.28

This counter is incremented when a station is transmitting
and its TRR timer expires. This condition denotes a condition
transmitting station in strip mode does not receive the
trailer of the frame TRR timer goes off.

ibmOsaExpTRRcvCongestionCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.29

This counter is incremented when a station
recognizes a frame addressed to its specific address, but
has no available buffer space indicating that the station
is congested.

ibmOsaExpTRFrameCopyErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.30

This counter is incremented when a station recognizes a
frame addressed to its specific address and detects that the
FS field A bits are set to 1 indicating a possible line hit
or duplicate address.

ibmOsaExpTRTokenErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.31

This counter is incremented when a station acting as the
active monitor recognizes an error condition that needs a
token transmitted.

ibmOsaExpTRFullDuplexErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.32

An error has been detected by the FDX protocol

ibmOsaExpTRSoftErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.33

The number of Soft Errors the interface
has detected. It directly corresponds to
the number of Report Error MAC frames
that this interface has transmitted.
Soft Errors are those which are
recoverable by the MAC layer pr…

ibmOsaExpTRHardErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.34

The number of times this interface has
detected an immediately recoverable
fatal error. It denotes the number of
times this interface is either
transmitting or receiving beacon MAC frames.

ibmOsaExpTRSignalLossErrorCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.35

The number of times this interface has
detected the loss of signal condition from the ring.

ibmOsaExpTRTransmitBeaconCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.36

The number of times this interface has
transmitted a beacon frame.

ibmOsaExpTRRecoveryCounter

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.37

The number of Claim Token MAC frames received or
transmitted after the interface has received a frame Ring
Ring Purge MAC counter signifies the number of times the
ring has been purged and is being recovered back into a…

ibmOsaExpTRLobeWireFaultCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.38

The number of times the interface has
detected an open or short circuit in the
lobe data path. The adapter will be closed
and ibmOsaExpTRRingState will signify this condition.

ibmOsaExpTRRemoveReceivedCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.39

The number of times the interface has received a Remove
Ring Station MAC frame request. When this frame is
received the interface will enter the closed state and
ibmOsaExpTRRingState will signify this condition.

ibmOsaExpTRSingleStationCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.40

The number of times the interface has
sensed that it is the only station on the
ring. This will happen if the interface
is the first one up on a ring, or if
there is a hardware problem.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.5.1.41

ibmOSAExpATMPortTable

table

.1.3.6.1.4.1.2.6.188.1.7 · 1 row entry · 76 columns

Open in standard view

Uses the ibm variant from /opt/observium/mibs/ibm.

Command help

Walk ibmOSAExpATMPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'IBM-OSA-MIB' -M '/opt/observium/mibs/ibm:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'IBM-OSA-MIB::ibmOSAExpATMPortTable'

This table represents the data associated with an emulated
Ethernet port on an OSA-Express ATM feature.
There are a maximum of 2 logical ports on each ATM feature,
however, each port is shown as though it exists independently
with each having an entry in the ibmOSAExpChannelTable.

ibmOSAExpATMPortEntry row .1.3.6.1.4.1.2.6.188.1.7.1

Definition of a single entry in the ibmOSAExpATMPortTable.
Indexed by the ifIndex of the corresponding Device interface.

Indexes

ibmOsaExpATMLanTrafficState

Column Syntax OID

ibmOsaExpATMPortNumber

The logical port number of this port

Integer32

Constraints:
range: 0-3

.1.3.6.1.4.1.2.6.188.1.7.1.1

ibmOsaExpATMPortType

The logical port type.

Enumeration

Enumerated Values:

17	emulatedEthernet

.1.3.6.1.4.1.2.6.188.1.7.1.2

The LAN state value ranges from 0 to 8. A value of 5,
disabled is further explained in object
ibmOsaExpATMDisabledStatus.

Enumeration

Enumerated Values:

0	undefined
1	unavailable
2	enabling
3	disabling
4	enabled
5	disabled
6	linkMonitor
7	definitionError
8	configuredOffline

.1.3.6.1.4.1.2.6.188.1.7.1.3

ibmOsaExpATMServiceMode

This object indicates if the processor is in service mode
or not.

Enumeration

Enumerated Values:

0	notInServiceMode
1	inServiceMode

.1.3.6.1.4.1.2.6.188.1.7.1.4

ibmOsaExpATMDisabledStatus

When the value of ibmOsaExpATMLanTrafficState is NOT
disabled, the value of this object will be zero.

When the value of ibmOsaExpATMLanTrafficState is
disabled(5), this object explains the reason for the
…

Bits

Enumerated Values:

0	reserved0
1	internalPortFailure
2	reserved2
3	reserved3
4	reserved4
5	reserved5
6	portTemporarilyDisabled
7	reserved7
8	reserved8
9	serviceProcessorRequest
10	networkRequest
11	osasfRequest
12	configurationChange
13	linkFailureThresholdExceeded
14	reserved14
15	reserved15

.1.3.6.1.4.1.2.6.188.1.7.1.5

ibmOsaExpATMConfigName

This is the name of the configuration that is on the OSA.
It is set using OSA/SF. It is not used by OSA

OctetString

Constraints:
range: 0-34

.1.3.6.1.4.1.2.6.188.1.7.1.6

ibmOsaExpATMMacAddrActive

A 6 byte OCTET STRING which contains the current
MAC address in use on the OSA.
The values are in canonical format.

OctetString

Constraints:
range: 6-6

.1.3.6.1.4.1.2.6.188.1.7.1.7

ibmOsaExpATMMacAddrBurntIn

A 6 byte OCTET STRING which contains the burned in
MAC address on the OSA.
The values are in canonical format.

OctetString

Constraints:
range: 6-6

.1.3.6.1.4.1.2.6.188.1.7.1.8

ibmOsaExpATMUserData

Data set by the user. It is ignored by the OSA.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.2.6.188.1.7.1.9

ibmOsaExpATMPortName

Name of the port as used by TCP/IP

OctetString

Constraints:
range: 0-8

.1.3.6.1.4.1.2.6.188.1.7.1.12

ibmOsaExpATMGroupMacAddrTable

This field contains the active Group Addresses.
An individual Group Address is 6 bytes long with an
additional 2 bytes of padding.

OctetString

Constraints:
range: 256-256

.1.3.6.1.4.1.2.6.188.1.7.1.13

ibmOsaExpATMIBMEnhancedMode

When set to Yes, this keeps data connections active
when the connection to the LES is lost.

Enumeration

Enumerated Values:

0	no
1	yes

.1.3.6.1.4.1.2.6.188.1.7.1.14

ibmOsaExpATMBestEffortPeakRate

Values range from 10-1550 and must be divided by 10 to
get the proper value. A value of 1550 indicates 155.0
Mbytes/sec

Megabytes per secondSNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.2.6.188.1.7.1.15

ibmOsaExpATMConfigMode

Indicates whether this LAN Emulation Client should
auto-configure the next time it is (re)started. In
automatic (1) mode, a client uses a LAN Emulation
Configuration Server to learn the ATM address of its
LAN Emulation …

Enumeration

Enumerated Values:

1	automatic
2	manual

.1.3.6.1.4.1.2.6.188.1.7.1.16

ibmOsaExpATMConfigLanType

The logical port type that the user configured the port for

Enumeration

Enumerated Values:

17	emulatedEthernet

.1.3.6.1.4.1.2.6.188.1.7.1.17

ibmOsaExpATMActualLanType

The actual logical port type the port is running in

Enumeration

Enumerated Values:

17	emulatedEthernet

.1.3.6.1.4.1.2.6.188.1.7.1.18

ibmOsaExpATMConfigMaxDataFrmSz

The maximum data frame size (in bytes) which this
client will use the next time it returns to the Initial
State. Auto-configuring clients use this parameter in
their configure requests. Manually configured clients use
i…

bytesEnumeration

Enumerated Values:

1	unspecified
2	f1516
3	f4544
4	f9234
5	f18190

.1.3.6.1.4.1.2.6.188.1.7.1.19

ibmOsaExpATMActualMaxDataFrmSz

Enumeration

Enumerated Values:

1	unspecified
2	f1516
3	f4544
4	f9234
5	f18190

.1.3.6.1.4.1.2.6.188.1.7.1.20

ibmOsaExpATMConfigELANName

The ELAN Name this client will use the
next time it returns to the Initial State.
Auto-configuring clients use this parameter in
their configure requests. Manually configured
clients use it in their join requests.

OctetString

Constraints:
range: 0-36

.1.3.6.1.4.1.2.6.188.1.7.1.21

ibmOsaExpATMActualELANName

OctetString

Constraints:
range: 0-36

.1.3.6.1.4.1.2.6.188.1.7.1.22

ibmOsaExpATMConfigLESATMAddress

The LAN Emulation Server which this client will use the
next time it is started in manual configuration mode.
When ibmOsaExpATMConfigMode is 'automatic', there is no
need to set this address, Address) and no advantage t…

OctetString

Constraints:
range: 20-20

.1.3.6.1.4.1.2.6.188.1.7.1.23

ibmOsaExpATMActualLESATMAddress

The LAN Emulation Server which this client will use the
next time it is started in manual configuration mode.
When lecConfigMode is 'automatic', there is no need to set
this address, Address) and no advantage to doing s…

OctetString

Constraints:
range: 20-20

.1.3.6.1.4.1.2.6.188.1.7.1.24

ibmOsaExpATMControlTimeout

Control Time-out. Time out period used for timing out most
request/response control frame interactions, as specified
elsewhere in the LAN Emulation specification.
This time value is expressed in seconds. Corresponds to
…

secondsInteger32

Constraints:
range: 10-300

.1.3.6.1.4.1.2.6.188.1.7.1.25

ibmOsaExpATMMaxUnknownFrameCount

Maximum Unknown Frame Count. See the description of
ibmOsaExpATMMaxUnknownFrameTime below. Corresponds to
Initial State Parameter C10.

Integer32

Constraints:
range: 1-10

.1.3.6.1.4.1.2.6.188.1.7.1.26

ibmOsaExpATMMaxUnknownFrameTime

Maximum Unknown Frame Time. Within the period of time
defined by the Maximum Unknown Frame Time, a LE Client
will send no more than Maximum Unknown Frame Count
frames to the BUS for a given unicast LAN Destination,
and …

Integer32

Constraints:
range: 1-60

.1.3.6.1.4.1.2.6.188.1.7.1.27

ibmOsaExpATMVCCTimeoutPeriod

VCC Time-out Period. A LE Client SHOULD release any
Data Direct VCC that it has not used to transmit
or receive any data frames for the length of the VCC
Time-out Period. This parameter is only meaningful for
SVC Data D…

secondsSNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.2.6.188.1.7.1.28

ibmOsaExpATMMaxRetryCount

Maximum Retry Count. A LE CLient MUST not retry a
LE_ARP_REQUEST for a given frame's LAN destination
more than Maximum Retry Count times, after the first
LE_ARP_REQUEST for that same frame's LAN destination.
Corresponds…

ibmOsaExpATMForwardDelayTime

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.29

ibmOsaExpATMAgingTime

Aging Time. The maximum time that a LE Client will
maintain an entry in its LE_ARP cache in the absence
of a verification of that relationship.
This time value is expressed in seconds. Corresponds to
Initial State Param…

secondsInteger32

Constraints:
range: 10-300

.1.3.6.1.4.1.2.6.188.1.7.1.30

Forward Delay Time. The maximum time that a LE Client
will maintain an entry for a non-local MAC address in
its LE_ARP cache in the absence of a verification of
that relationship, as long as the Topology Change flag
C19…

secondsInteger32

Constraints:
range: 4-30

.1.3.6.1.4.1.2.6.188.1.7.1.31

ibmOsaExpATMExpectedARPRespTime

Expected LE_ARP Reponse Time. The maximum time that
the LEC expects an LE_ARP_REQUEST/LE_ARP_RESPONSE
cycle to take. Used for retries and verifies. This
time value is expressed in seconds.
Corresponds to Initial State P…

secondsInteger32

Constraints:
range: 1-30

.1.3.6.1.4.1.2.6.188.1.7.1.32

ibmOsaExpATMFlushTimeout

Flush Time-out. Time limit to wait to receive a
LE_FLUSH_RESPONSE after the LE_FLUSH_REQUEST has been
sent before taking recovery action. This time value
is expressed in seconds. Corresponds to Initial State
Parameter C…

secondsInteger32

Constraints:
range: 1-4

.1.3.6.1.4.1.2.6.188.1.7.1.33

ibmOsaExpATMPathSwitchingDelay

Path Switching Delay. The time since sending a
frame to the BUS after which the LE Client may
assume that the frame has been either discarded
or delivered to the recipient. May be used to
bypass the Flush protocol. This…

secondsInteger32

Constraints:
range: 1-8

.1.3.6.1.4.1.2.6.188.1.7.1.34

ibmOsaExpATMLocalSegmentID

Local Segment ID. The segment ID of the emulated LAN.
This is only required for IEEE 802.5 clients that
are Source Routing bridges. Corresponds to Initial
State Parameter C23.

Integer32

Constraints:
range: 0-4095

.1.3.6.1.4.1.2.6.188.1.7.1.35

ibmOsaExpATMMltcstSendVCCType

Multicast Send VCC Type. Signalling parameter that
SHOULD be used by the LE Client when establishing
the Multicast Send VCC. This is the method to be used
by the LE Client when specifying traffic parameters
when it sets…

Enumeration

Enumerated Values:

1	bestEffort
2	variableBitRate
3	constantBitRate

.1.3.6.1.4.1.2.6.188.1.7.1.36

ibmOsaExpATMMltcstSendVCCAvgRate

Multicast Send VCC AvgRate. Signalling parameter
that SHOULD be used by the LE Client when estabishing
the Multicast Send VCC. Forward and Backward Sustained
Cell Rate to be requested by LE Client when setting
up Multic…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.2.6.188.1.7.1.37

ibmOsaExpATMMcastSendVCCPeakRate

Multicast Send VCC PeakRate. Signalling parameter that
SHOULD be used by the LE Client when establishing the
Multicast Send VCC. Forward and Backward Peak Cell
Rate to be requested by LE Client when setting up the
Multi…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.2.6.188.1.7.1.38

ibmOsaExpATMConnectCompleteTimer

Connection Complete Timer. Optional. In Connection
Establish ment this is the time period in which
data or a READY_IND message is expected from a Calling
Party. This time value is expressed in seconds.
Corresponds to In…

secondsInteger32

Constraints:
range: 1-10

.1.3.6.1.4.1.2.6.188.1.7.1.39

ibmOsaExpATMClientATMAddress

LE Client's ATM Addresses. The primary ATM address
of this LAN Emulation Client. This address is used
to establish the Control Direct and Multicast Send
VCCs, and may also be used to set up Data Direct
VCCs. A client ma…

OctetString

Constraints:
range: 20-20

.1.3.6.1.4.1.2.6.188.1.7.1.40

ibmOsaExpATMClientIdentifier

LE Client Identifier. Each LE Client requires a
LE Client Identifier (LECID) assigned by the LE
Server during the Join phase. The LECID is placed
in control requests by the LE Client and MAY be used
for echo suppression…

Integer32

Constraints:
range: 0-65279

.1.3.6.1.4.1.2.6.188.1.7.1.41

ibmOsaExpATMClientCurrentState

The current state of the LAN Emulation Client. Note
that 'ifOperStatus' is defined to be 'up' when, and
only when, this field is 'operational'.

Enumeration

Enumerated Values:

1	initialState
2	lecsConnect
3	configure
4	join
5	initialRegistration
6	busConnect
7	operational

.1.3.6.1.4.1.2.6.188.1.7.1.42

ibmOsaExpATMLastFailureRespCode

Status code from the last failed Configure response
or Join response. Failed responses are those for which
the LE_CONFIGURE_RESPONSE / LE_JOIN_RESPONSE frame
contains a non-zero code, or fails to arrive within a
timeout…

Enumeration

Enumerated Values:

1	none
2	timeout
3	undefinedError
4	versionNotSupported
5	invalidRequestParameters
6	duplicateLanDestination
7	duplicateAtmAddress
8	insufficientResources
9	accessDenied
10	invalidRequesterId
11	invalidLanDestination
12	invalidAtmAddress
13	noConfiguration
14	leConfigureError
15	insufficientInformation

.1.3.6.1.4.1.2.6.188.1.7.1.43

ibmOsaExpATMLastFailureState

The state this client was in when it updated the
'ibmOsaExpATMLastFailureRespCode'.
If 'ibmOsaExpATMLastFailureRespCode'
is 'none', this object has the value initialState(1).

Enumeration

Enumerated Values:

1	initialState
2	lecsConnect
3	configure
4	join
5	initialRegistration
6	busConnect
7	operational

.1.3.6.1.4.1.2.6.188.1.7.1.44

ibmOsaExpATMProtocol

The LAN Emulation protocol which this client supports,
and specifies in its LE_JOIN_REQUESTs.

Integer32

Constraints:
range: 1-255

.1.3.6.1.4.1.2.6.188.1.7.1.45

ibmOsaExpATMLeVersion

The LAN Emulation protocol version which this client
supports, and specifies in its LE_JOIN_REQUESTs.

Integer32

Constraints:
range: 1-255

.1.3.6.1.4.1.2.6.188.1.7.1.46

ibmOsaExpATMTopologyChange

Topology Change. Boolean indication that the LE Client
is using the Forward Delay Time C18, instead of the
Aging Time C17, to age non-local entries in its LE_ARP
cache C16. For a client which is not connected to the
LES…

Enumeration

Enumerated Values:

1	true
2	false

.1.3.6.1.4.1.2.6.188.1.7.1.47

ibmOsaExpATMConfigServerATMAddr

The ATM address of the LAN Emulation Configuration
Server (if known) or 0 (otherwise). In LAN
Emulation MIB, the OCTET STRING is either 0 length
or 20 octets.

For OSA-ATM, this Address has been
changed to…

OctetString

Constraints:
range: 20-20

.1.3.6.1.4.1.2.6.188.1.7.1.48

ibmOsaExpATMConfigSource

Indicates whether this LAN Emulation Client used the
LAN Emulation Configuration Server, and, if so, what
method it used to establish the Configuration Direct VCC

Enumeration

Enumerated Values:

1	gotAddressViaIlmi
2	usedWellKnownAddress
3	usedLecsPvc
4	didNotUseLecs

.1.3.6.1.4.1.2.6.188.1.7.1.49

ibmOsaExpATMProxyClient

Indicates whether this client is acting as a proxy.
Proxy clients are allowed to represent unregistered
MAC addresses, and receive copies of LE_ARP_REQUEST
frames for such addresses. Corresponds to Initial
State Paramet…

Enumeration

Enumerated Values:

1	true
2	false

.1.3.6.1.4.1.2.6.188.1.7.1.50

ibmOsaExpATMLePDUOctetsInbound

The number of Le PDU Octets received

octetsSNMPv2-SMICounter64

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.2.6.188.1.7.1.51

ibmOsaExpATMNonErrLePDUDiscIn

The number of Non Error Le PDU Octets received

octetsSNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.52

ibmOsaExpATMErrLePDUDiscIn

The number of Errored Le PDU Discards received

ibmOsaExpATMLePDUOctetsOutbound

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.53

The number of Le PDU Discards sent

octetsSNMPv2-SMICounter64

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.2.6.188.1.7.1.54

ibmOsaExpATMNonErrLePDUDiscOut

The number of Non Error Le PDU Discards sent

ibmOsaExpATMErrLePDUDiscOut

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.55

The number of Errored Le PDU Discards sent

ibmOsaExpATMLeARPRequestsOut

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.56

The number of LE ARP Requests sent

ibmOsaExpATMLeARPRequestsIn

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.57

The number of LE ARP Requests received over the LUNI
by this LAN Emulation Client. Requests may arrive
on the Control Direct VCC or on the Control Distribute
VCC, depending upon how the LES is implemented and the
chance…

ibmOsaExpATMLeARPRepliesOut

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.58

The number of LE ARP Responses sent over the LUNI
by this LAN Emulation Client.

ibmOsaExpATMLeARPRepliesIn

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.59

The number of LE ARP Responses received over the
LUNI by this LAN Emulation Client. This count includes
all such replies, whether solicited or not. Replies
may arrive on the Control Direct VCC or on the
Control Distribu…

ibmOsaExpATMControlFramesOut

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.60

The total number of control packets sent by this
LAN Emulation Client over the LUNI.

ibmOsaExpATMControlFramesIn

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.61

The total number of control packets received by this
LAN Emulation Client over the LUNI.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.2.6.188.1.7.1.62

ibmOsaExpATMSVCFailures

The total number of outgoing LAN Emulation SVCs
which this client tried, but failed, to open;
incoming LAN Emulation SVCs which this client tried,
but failed to establish; and incoming LAN Emulation
SVCs which this clie…