This MIB is used for defining Huawei's etherlike extended attributes, including
ETH port, vlan, service-port, MAC address, queue, Ip traffic parameters, HQos,
Net-role, traffic controling.
Trap of display location query.
The trap that is generated when IP or MAC address changed.
hwSrvDelInfoTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.10
This trap is sent when a traffic stream is deleted.
hwSrvAttrChangedInfoTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.11
This trap is sent when the traffic stream attribute is modified.
hwSrvFlowBundleTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.12
The trap generated when service virtual port bundle created or deleted.
hwSrvFlowBatModifyInfoTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.13
The trap generated when service virtual port batch modifyed.
hwEthernetLoopbackTestTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.14
This trap will be sent when a ethernet loopback test finished successfully. The trap shows the result of the loopback test.
hwEthernetPortCfgChangeTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.15
The trap generated when ethernet port configuration modified.
hwEthernetPortAggCfgChangeTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.16
The trap generated when a link-aggregation group of Ethernet ports is created, modified or deleted.
If you run this command with all specified, the system reports only one trap with hwPortIndex set to 255 for boards configured with link aggregation.
hwQryGlobalStatisticTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.2
Trap of one key mode of query flow quantity.
The trap that is generated when query global statistics.
hwBitsPortStatusChangeInfoTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.3
The trap generated when BITS port state changes
hwBindBoardOprateResultInfoTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.4
The trap generated when bind board or undo bind board, The first two FrameIndex And SlotIndex is Masterborad, and the other is SlaveBoard
hwPortSpeedTypeSwitchResultInfoTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.5
The trap generated when port speed type switched
hwPortStateChangeInfoTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.6
This trap message is generated when the port status changes,
for example from up to down or from down to up. The parameter
information about the trap message describes the current status
of the link and the location where the trap message is generated.
hwIpTrafficParamChangeTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.7
The trap generated when ip traffic profile created, deleted or modified.
hwPortAutounloopSwitchInfoTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.8
A trap message is generated when the loopback on a port is canceled automatically.
hwSrvAddInfoTrap
.1.3.6.1.4.1.2011.5.14.10.1.0.9
This trap is sent when a traffic stream is set up.
hwAlarmEthernetPortOffline
.1.3.6.1.4.1.2011.5.14.10.2.0.1
Alarm description: port offline
explanation: LAN port offline, the line is not connected
resolving method: change the line or check the peer port
alarm description: the port is offline.
The trap generated when the port is offline.
hwAlarmLOLOccurInBITSInputPort
.1.3.6.1.4.1.2011.5.14.10.2.0.10
This trap is sent when the loss of link (LOL) occurs in the BITS input port.
hwAlarmEthernetPortStatusChanges
.1.3.6.1.4.1.2011.5.14.10.2.0.11
This trap is sent when the Ethernet port link status changes from up to down.
hwAlarmOpticalTransceiverAbsence
.1.3.6.1.4.1.2011.5.14.10.2.0.12
This trap is sent when the optical transceiver is absence.
hwAlarmLOSOccurs
.1.3.6.1.4.1.2011.5.14.10.2.0.13
This trap is sent when the LOS occurs on the Ethernet optical port.
hwAlarmLinkBetweenStackPortsFails
.1.3.6.1.4.1.2011.5.14.10.2.0.14
This trap is sent when the Link between stack ports fails.
hwAlarmUpstreamEthernetPortConnectRecover
.1.3.6.1.4.1.2011.5.14.10.2.0.15
This trap is sent when the upstream ethernet port connection failure recovers or the state of it is normal.
hwAlarmOpticalPortTemperatureRecover
.1.3.6.1.4.1.2011.5.14.10.2.0.16
This trap is sent when the temperature of the Ethernet optical port recovers to the normal range.
hwAlarmBITSInputRecover
.1.3.6.1.4.1.2011.5.14.10.2.0.17
This trap is sent when the BITS input port recovers from loss of link (LOL).
hwAlarmEthernetPortLinkStatusChange
.1.3.6.1.4.1.2011.5.14.10.2.0.18
This trap is sent when the Ethernet port link status changes from down to up.
hwAlarmOpticalTransceiverRecover
.1.3.6.1.4.1.2011.5.14.10.2.0.19
This trap is sent when the optical transceiver recovers to the normal state.
hwAlarmEthernetPeerPortNoNeg
.1.3.6.1.4.1.2011.5.14.10.2.0.2
Alarm description: peer port does not support auto-negotiation.
Explanation: this port is auto-negotiation alarm, while the peer port is non-auto-negotiation alarm.
Resolution: Modify the mode of the peer port as auto-negotiation, or set the mode of this port as the non-auto-negotiation mode. In addition, ensure that the parameters under the non-auto-negotiation mode are consistent with the peer port, including the duplex mode, the rate and whether to support PAUSE frame.
hwAlarmOpticalPortRecoverFromLOS
.1.3.6.1.4.1.2011.5.14.10.2.0.20
This trap is sent when the Ethernet optical port recovers from LOS.
hwAlarmLinkBetweenStackPortsRecover
.1.3.6.1.4.1.2011.5.14.10.2.0.21
This trap is sent when the link between stack ports on the boards to be bound returns to a normal status.
hwOpticsTxPowerOutOfRangeAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.22
This trap is sent when the Tx power of the Ethernet optical port is out of the range.
hwOpticsTxPowerRestoreAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.23
This trap is sent when the Tx power of the Ethernet optical port recovers to the normal range.
hwOpticsRxPowerOutOfRangeAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.24
This trap is sent when the Rx power of the Ethernet optical port is out of the range.
hwOpticsRxPowerRestoreAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.25
This trap is sent when the Rx power of the Ethernet optical port recovers to the normal range.
hwAlarmEthPoePowerHighFault
.1.3.6.1.4.1.2011.5.14.10.2.0.26
This trap is sent when the load power of the Power over Ethernet port exceeds the upper limit.
hwAlarmEthPoePowerHighRecover
.1.3.6.1.4.1.2011.5.14.10.2.0.27
This trap is sent when the load power of the Power over Ethernet port recovers.
hwAlarmEthPoeCurrHighFault
.1.3.6.1.4.1.2011.5.14.10.2.0.28
This trap is sent when the Overcurrent for the power supply of the Power over Ethernet port.
hwAlarmEthPoeCurrHighRecover
.1.3.6.1.4.1.2011.5.14.10.2.0.29
This trap is sent when the Overcurrent for the power supply of the Power over Ethernet port recovers.
hwAlarmEthernetMacLost
.1.3.6.1.4.1.2011.5.14.10.2.0.3
Alarm description: MAC is lost
explanation: The user MAC connected with IP DSLAM is lost.
Resolution: Adjust the max MAC learning of PVC.
Because in the connection with IP DSLAM, the number of a PVC can learn is limited,the user MAC will be lost if the number is bigger than the limited number.
hwAlarmEthernetPortAdminActivate
.1.3.6.1.4.1.2011.5.14.10.2.0.30
This trap is sent when the ETH port is activated.
hwAlarmEthernetPortAdminDeActivate
.1.3.6.1.4.1.2011.5.14.10.2.0.31
This trap is sent when the ETH port is deactivated.
hwAlarmEthPowerDyingGaspFault
.1.3.6.1.4.1.2011.5.14.10.2.0.32
This trap is sent when the remote device is powered off.
hwAlarmEthPowerDyingGaspRecover
.1.3.6.1.4.1.2011.5.14.10.2.0.33
This trap is sent when the remote device is powered on.
hwOpticsTemperatureOutOfRangeAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.34
This trap is sent when the Temperature of the Ethernet optical port is out of the range.
hwOpticsTemperatureRestoreAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.35
This trap is sent when the Temperature of the Ethernet optical port recovers to the normal range.
hwOpticsVoltageOutOfRangeAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.36
This trap is sent when the Voltage of the Ethernet optical port is out of the range.
hwOpticsVoltageRestoreAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.37
This trap is sent when the Voltage of the Ethernet optical port recovers to the normal range.
hwOpticsCurrentOutOfRangeAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.38
This trap is sent when the Current of the Ethernet optical port is out of the range.
hwOpticsCurrentRestoreAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.39
This trap is sent when the Current of the Ethernet optical port recovers to the normal range.
hwAlarmEthernetPortActive
.1.3.6.1.4.1.2011.5.14.10.2.0.4
This trap is sent when the LAN port has been actived from other state.
alarm description: port active
explanation: LAN port active
resolving method:No process to need
hwEthPerformanceStatisOutOfRangeAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.40
This trap is sent when the Current alarm performance statistics of the Ethernet port is out of the range.
hwEthPerformanceStatisRestoreAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.41
This trap is sent when the Current alarm performance statistics of the Ethernet port recovers to the normal range.
hwEthPerformanceStatisOutOfRangeWarningTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.42
This trap is sent when the Current warning performance statistics of the Ethernet port is out of the range.
hwEthPerformanceStatisRestoreWarningTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.43
This trap is sent when the Current warning performance statistics of the Ethernet port recovers to the normal range.
hwMacOverloadTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.44
This trap is sent when the MAC address occupancy in the system exceeds the upper threshold.
hwMacOverloadRestoreTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.45
This trap is sent when the MAC address occupancy in the system is lower than the lower threshold.
hwIPNeighbourHardwareOverloadTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.46
This trap is sent when the IP neighbour hardware occupancy in the system exceeds the upper threshold.
hwIPNeighbourHardwareOverloadRestoreTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.47
This trap is sent when the IP neighbour hardware occupancy in the system is lower than the lower threshold.
hwBindBoardReplaceErrorTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.48
This trap is sent when one bind board has been replaced while the other one hasn't been replaced.
hwEnableMirrorPortTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.49
This trap is sent when a mirror port has been created.
1: hwFrameIndex -indicates the source frame index.
2: hwSlotIndex -indicates the source slot index.
3: hwPortIndex -indicates the source port index.
4: hwFrameIndex -indicates the destination frame index.
5: hwSlotIndex -indicates the destination slot index.
6: hwPortIndex -indicates the destination port index.
7: hwEthernetMirrorDirection -indicates the mirror direction.
hwAlarmEthernetPortDeActive
.1.3.6.1.4.1.2011.5.14.10.2.0.5
This trap is sent when the lan port has been deactivated from other state.
alarm description: port deactivated
explanation: LAN port deactivated
resolving method:check port status is active
hwDisableMirrorPortTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.50
This trap is sent when a mirror port has been cancelled.
1: hwFrameIndex -indicates the source frame index.
2: hwSlotIndex -indicates the source slot index.
3: hwPortIndex -indicates the source port index.
4: hwFrameIndex -indicates the destination frame index.
5: hwSlotIndex -indicates the destination slot index.
6: hwPortIndex -indicates the destination port index.
7: hwEthernetMirrorDirection -indicates the mirror direction.
hwBoardMacOverloadTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.51
This trap is sent when the MAC address occupancy on the board exceeds the upper threshold.
hwBoardMacOverloadRestoreTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.52
This trap is sent when the MAC address occupancy on the board is lower than the lower threshold.
hwEnableMirrorPortExtendTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.53
This trap is sent when mirroring is configured by running the mirror port command in SU mode.
1: hwMirrorSrcPortDescription -indicates the description of the source port with the format frameId/slotId/portid.
2: hwMirrorDstPortDescription -indicates the description of the destination port with the format frameId/slotId/portid or meth.
3: hwEthernetMirrorDirection -indicates the mirror direction.
hwDisableMirrorPortExtendTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.54
This trap is sent when mirroring is canceled by running the undo mirror port command in SU mode.
1: hwMirrorSrcPortDescription -indicates the description of the source port with the format frameId/slotId/portid.
2: hwMirrorDstPortDescription -indicates the description of the destination port with the format frameId/slotId/portid or meth.
3: hwEthernetMirrorDirection -indicates the mirror direction.
hwOpticsLaserTemperatureOutOfRangeAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.55
This trap is sent when the temperature of the Ethernet optical port laser is out of the range.
hwOpticsLaserTemperatureRestoreAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.56
This trap is sent when the temperature of the Ethernet optical port laser recovers within the normal range.
hwOpticsWavelengthOutOfRangeAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.57
This trap is sent when the wavelength sent by the optical module on the Ethernet port is out of the range.
hwOpticsWavelengthRestoreAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.58
This trap is sent when the wavelength sent by the optical module on the Ethernet port recovers within the normal range.
hwOpticTecCurrentOutOfRangeAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.59
This trap is sent when the current of the thermoelectric cooler on the Ethernet optical port is out of the range.
hwMacConflictTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.6
When the source MAC got by non-network-side ports is the same as one learned by network-side ports,
this trap will be generated.
hwOpticsTecCurrentRestoreAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.60
This trap is sent when the current of the thermoelectric cooler on the Ethernet optical port recovers within the normal range.
hwIPRouteHardwareOverloadTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.61
This trap is sent when the IP route hardware occupancy in the system exceeds the upper threshold.
hwIPRouteHardwareOverloadRestoreTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.62
This trap is sent when the IP route hardware occupancy in the system is lower than the lower threshold.
hwPortAutoServiceAddFailureTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.63
Trap indicating that automatic service port creation upon an ONT being online fails.
hwPortAutoServiceParaIncorrectTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.64
Trap indicating that parameters for automatic service port creation are incorrect.
hwPortCmtsFrameAddFailTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.65
This trap is sent when board resources are full and the extended frame cannot be added.
hwMacConflictNewTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.66
When the source MAC got by a port is the same as one learnt by another, this trap will be generated.
When the port is configured with PW, hwExtSrvFlowIndex indicates PW index, and the values of hwFrameIndex,
hwSlotIndex and hwPortIndex are invalid value.
hwMacAddressFlappingOverTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.67
When the number of flapping MAC addresses reaches or exceeds the preset upper threshold, this trap will be generated.
hwMacAddressFlappingOverRestoreTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.68
When the number of flapping MAC addresses is smaller than or equal to the preset lower threshold, this trap will be generated.
hwMacLimitOverflowTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.69
When the number of learnable MAC addresses of this port reaches the limit, this trap will be generated.
hwAlarmEthernetPortTransceiverTypeChange
.1.3.6.1.4.1.2011.5.14.10.2.0.7
This trap is sent when the transceiver type of the Ethernet port changes.
hwMacLimitOverflowRecoverTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.70
When the number of learnable MAC addresses of this port recovery normal, this trap will be generated.
hwUpstreamDecreaseRecordTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.71
When the number of reduced upstream traffic by the specified uplink-port exceeds the
specified threshold, this trap will be generated.
hwDownstreamDecreaseRecordTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.72
When the number of reduced downstream traffic by the specified uplink-port exceeds the
specified threshold, this trap will be generated.
hwStreamDecreaseRecordTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.73
When the number of reduced upstream and downstream traffic by the specified uplink-port exceeds the
specified threshold, this trap will be generated.
hwPacketAttackTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.74
The system records packet statistics based on port and protocol type when the current CPU usage exceeds the packet detection threshold.
hwInnerForwardingFaultAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.75
When the inner forwarding fault occurs, this trap will be generated.
hwInnerForwardingRecoverAlarmTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.76
When the inner forwarding recovery occurs, this trap will be generated.
hwDslamNonUnicastUpportMonitorRecordTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.77
The SNMP trap is generated when the number of non-unicast packets received by the uplink-port exceeds the threshold.
hwIPTunnelHardwareOverloadTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.78
This trap is sent when the IP tunnel hardware occupancy in the system exceeds the upper threshold.
hwIPTunnelHardwareOverloadRestoreTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.79
This trap is sent when the IP tunnel hardware occupancy in the system is lower than the lower threshold.
hwAlarmSoftwareVersionNotSame
.1.3.6.1.4.1.2011.5.14.10.2.0.8
Software versions of the boards to be bound are not the same.
The parameter information about the trap location where the
trap message is generated, The first hwSlotIndex indicate slot
ID of left board and second hwSlotIndex indicate slot ID of right board.
hwVPNHardwareOverloadTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.80
This trap is sent when the VNI peer hardware occupancy in the system exceeds the upper threshold.
hwVPNHardwareOverloadRestoreTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.81
This trap is sent when the VNI peer hardware occupancy in the system is lower than the lower threshold.
hwSRv6TunnelHardwareOverloadTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.82
This trap is sent when the segment-routing ipv6 tunnel hardware occupancy in the system exceeds the upper threshold.
hwSRv6TunnelHardwareOverloadRestoreTrap
.1.3.6.1.4.1.2011.5.14.10.2.0.83
This trap is sent when the segment-routing ipv6 tunnel hardware occupancy in the system is lower than the lower threshold.
hwAlarmUpstreamPortConnectfail
.1.3.6.1.4.1.2011.5.14.10.2.0.9
This trap is sent when the upstream ethernet port connection fails or the state of it is abnormal.
hwInfinibandPortLinkDown
.1.3.6.1.4.1.2011.5.14.32.1.0.1
This trap message is generated when the infiniband port status changes form up to down.
hwInfinibandPortLinkRecover
.1.3.6.1.4.1.2011.5.14.32.1.0.2
This trap message is generated when the infiniband port status changes form down to up.
HwDynamicMacQueryPara
hwEthernetPort 
hwSlotPortMax 
hwBoardMacAddressLearningVlanConnectTable 
hwBoardMacAddressLearningVlanConnectEntry 
hwBoardMacAddressLearningVlanConnectCtrl 
hwIpdslamDisplayLocationTrap