HUAWEI-ETHERLIKE-EXT-MIB Table View

Indicates the line parameter configuration table of an ETH port. 
It is used for setting the rate, duplex, auto-negotiation, MDI, 
traffic control, Combo mode of an Ethernet port.
The index of this table is ifIndex.

hwEthernetEntry row .1.3.6.1.4.1.2011.5.14.1.4.1

Indicates the line parameter configuration table of an ETH port.
It is used for setting the rate, duplex, auto-negotiation, MDI,
traffic control, Combo mode of an Ethernet port.
The index of this entry is ifIndex.

Indexes

IF-MIBifIndex

Column	Syntax	OID
hwifEthernetDuplex Ethernet port duplex mode. Options: 1. full(1) -indicates that at one moment, the port can be sending packets and receiving packets 2. half(2) -indicates that at one moment, the port can be sending packets or re…	Enumerationr/w Enumerated Values: -1 invalid 1 full 2 half 3 auto 4 autoFull 5 autoHalf	.1.3.6.1.4.1.2011.5.14.1.4.1.1
hwifEthernetMTU This object is used for setting the MTU of a ETH port 0 indicates to restore the default value. -1 indicates the value is invalid. Range: -1-0, 1519-9280	Integer32r/w Constraints: range: -1-0 range: 1519-9280	.1.3.6.1.4.1.2011.5.14.1.4.1.2
hwifEthernetSpeed Ethernet port rate. Options: 1. auto(0) -Ethernet port rate 0 2. s10M(10) -Ethernet port rate forced 10M 3. s100M(100) -Ethernet port rate forced 100M 4. s1000M(1000) -Ethernet p…	Enumerationr/w Enumerated Values: -1 invalid 0 auto 10 s10M 11 autoS10M 100 s100M 101 autoS100M 1000 s1000M 1001 autoS1000M 2500 s2500M 10000 s10000M 10001 autoS10000M 100000 s100000M	.1.3.6.1.4.1.2011.5.14.1.4.1.3
hwifEthernetLoopback Ethernet port loop back mode. Options: 1. noloopback(1) -cancel loopback 2. internalloopback(2) -local loopback 3. externalloopback(3) -remote loopback Ports only on the H801SPUA board support the loopback con…	Enumerationr/w Enumerated Values: 1 noloopback 2 internalloopback 3 externalloopback	.1.3.6.1.4.1.2011.5.14.1.4.1.4
hwifEthernetMdi Ethernet port cable type. Options: 1. mdiII(1) -direct connection cable 2. mdiX(2) -cross-over cable 3. mdiAuto(3) -auto-sensing 4. invalid(-1) -invalid value After the network cable auto-sensing mode of an Ethe…	Enumerationr/w Enumerated Values: -1 invalid 1 mdiII 2 mdiX 3 mdiAuto	.1.3.6.1.4.1.2011.5.14.1.4.1.5
hwMaxMacLearn The max MAC learned by the Ethernet port. The invalid value is 65535.	Integer32r/w Constraints: range: 0-600 range: 65535-65535	.1.3.6.1.4.1.2011.5.14.1.4.1.6
hwifMacAddressLearn Status indicates if the interface is allowed to learn MAC address. Options: 1. enabled(1) -Indicates the interface can learn MAC address. 2. disabled(2) -Indicates the interface can't learn MAC address. Enable the sel…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.2011.5.14.1.4.1.7
hwifTag Ethernet interface tag. Options: 1. tag(1) -This value is not supported. 2. untag(2) -This value is not supported. 3. multi(3) -This value is not supported.	Enumerationr/w Enumerated Values: 1 tag 2 untag 3 multi	.1.3.6.1.4.1.2011.5.14.1.4.1.8
hwifEthernetNegotiate Ethernet port negotiation mode. Options: 1. true(1) -auto-negotiation mode of an Ethernet port is enabled, Ethernet port automatically negotiates the port rate and duplex mode with the interconnected Ethe…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.14.1.4.1.9
hwifEthernetPeerNegotiate Ethernet peer port auto-negotiation node (which is needed by MA5100 V2R1 product, and can be selected by other products of the fixed network depending on the practice.)	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.14.1.4.1.10
hwifEthernetPauseFrameTag Whether the Ethernet port supports Pause frame flow control. Options: 1. on(1) -support Tx Pause and Rx Pause 2. off(2) -not support 3. rxpause(3) -support Rx Pause not support Tx Pause 4. txpause(4) -support…	Enumerationr/w Enumerated Values: 1 on 2 off 3 rxpause 4 txpause	.1.3.6.1.4.1.2011.5.14.1.4.1.11
hwifEthernetPauseFrameSending Ethernet pause frame sending tag (Notes: only for Huawei product of Ma5100) Whether the network interface is sending Pause frame (which is needed by MA5100 V2R1 product, and can be selected by other products of the fix…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.14.1.4.1.12
hwifEthernetVlanDefault Describes the native VLAN of an Ethernet port. When you need to set the packets of the upstream Ethernet port with the VLAN tag, operate this leaf. After the native VLAN of the Ethernet port is configured successfull…	Integer32r/w Constraints: range: -1--1 range: 1-4093	.1.3.6.1.4.1.2011.5.14.1.4.1.13
hwifEthernetOnlineState Ethernet port online status (Notes: only for Huawei product of Ma5100). Whether the network interface is online (which is needed by MA5100 V2R1 product, and can be selected by other products of the fixed network depend…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.14.1.4.1.14
hwifEthernetLineSelfAdaptMode Connecting adaptatively tag,default false. Options: 1. true(1) -adapting by itself 2. false(2) -adapting by manual The self-adaptation switch: In the case of true, the self-adaptation is enabled, and the…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.14.1.4.1.15
hwifEthernetTrafficBroadcast Indicates the broadcast traffic suppression on an Ethernet port. Range: -1,0-13 13: indicates full-suppression of traffic, and 0 indicates no traffic suppression. -1: indicates invalid value. The suppression levels an…	Integer32r/w Constraints: range: -1-13	.1.3.6.1.4.1.2011.5.14.1.4.1.16
hwifEthernetTrafficMulticast Indicates the unknown multicast traffic suppression on an Ethernet port. Range: -1,0-13 …	Integer32r/w Constraints: range: -1-13	.1.3.6.1.4.1.2011.5.14.1.4.1.17
hwifEthernetTrafficUnknowncast Indicates the unknown unicast traffic suppression on an Ethernet port. Range: -1,0-13 …	Integer32r/w Constraints: range: -1-13	.1.3.6.1.4.1.2011.5.14.1.4.1.18
hwifEthernetJumboEnable This object is used to enable or disable jumbo frames. When the carriers' servers need to exchange a large amount of data with their devices, operate this object to enable jumbo frames. After the operation is execute…	Enumerationr/w Enumerated Values: -1 invalid 1 enabled 2 disabled	.1.3.6.1.4.1.2011.5.14.1.4.1.19
hwifPortDefPriority Port default 802.1p priority (Notes: Default value is 0.) ------------------------------------------------------------ F/ S/ P Port Priority ------------------------------------------------------------ …	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.2011.5.14.1.4.1.20
hwifEthernetComboWorkMode Work mode information of combo port. Options: 1. electric(1) -combo port works in electric mode 2. optic(2) -combo port works in optic mode 3. autoFiber(5) -combo port works in auto adapter mode 4. invalid(-1) …	Enumerationr/w Enumerated Values: -1 invalid 1 electric 2 optic 5 autoFiber	.1.3.6.1.4.1.2011.5.14.1.4.1.21
hwifEthernetLineTest It used to test the line status. Options: 1. test(1) -Test the line operation 2. notSupport(-1) -Indicates the board does not support this operation	Enumerationr/w Enumerated Values: -1 notSupport 1 test	.1.3.6.1.4.1.2011.5.14.1.4.1.22
hwifEthernetAutoTxPowerOffSwitch Indicates the switch of Tx auto power off. Options: 1. invalid(-1) -invalid value 2. enabled(1) -enable Tx auto poweroff 3. disabled(2) -disable Tx auto poweroff Default: disable(2).	Enumerationr/w Enumerated Values: -1 invalid 1 enabled 2 disabled	.1.3.6.1.4.1.2011.5.14.1.4.1.23
hwifEthernetAutoTxPowerOffDetectTime Indicates the detecting LOS time of TX auto power off. Set: '1-60' means valid value to be set, Get: '-1' means invalid value, Unit: minutes	minutesInteger32r/w Constraints: range: -1--1 range: 1-60	.1.3.6.1.4.1.2011.5.14.1.4.1.24
hwifEthernetTxPowerState Indicates the state of ethernet port Tx. Options: 1. invalid(-1) -invalid value 2. on(1) -ethernet port Tx is on 3. off(2) -ethernet port Tx is off	Enumeration Enumerated Values: -1 invalid 1 on 2 off	.1.3.6.1.4.1.2011.5.14.1.4.1.25
hwEthBind15minAlarmTableIndex Indicates the 15 minutes alarm profile index for the ethernet port. Set: '0' means to unbind 15 minutes alarm profile, '1-16' means to bind 15 minutes alarm profile to the ethernet port Get: '-1' means operation not …	Integer32r/w Constraints: range: -1-16	.1.3.6.1.4.1.2011.5.14.1.4.1.26
hwEthBind15minWarningTableIndex Indicates the 15 minutes warning profile index for the ethernet port. Set: '0' means to unbind 15 minutes warning profile, '1-16' means to bind 15 minutes warning profile to the ethernet port Get: '-1' means operatio…	Integer32r/w Constraints: range: -1-16	.1.3.6.1.4.1.2011.5.14.1.4.1.27
hwEthBind24hourAlarmTableIndex Indicates the 24 hours alarm profile index for the ethernet port. Set: '0' means to unbind 24 hours alarm profile, '1-16' means to bind 24 hours alarm profile to the ethernet port Get: '-1' means operation not suppor…	Integer32r/w Constraints: range: -1-16	.1.3.6.1.4.1.2011.5.14.1.4.1.28
hwEthBind24hourWarningTableIndex Indicates the 24 hours warning profile index for the ethernet port. Set: '0' means to unbind 24 hours warning profile, '1-16' means to bind 24 hours warning profile to the ethernet port Get: '-1' means operation not …	Integer32r/w Constraints: range: -1-16	.1.3.6.1.4.1.2011.5.14.1.4.1.29
hwifEthernetPortType Indicates the ethernet port type. Options: 1. fe(1) -Ethernet port type FE 2. ge(2) -Ethernet port type GE 3. xge(3) -Ethernet port type 10GE 4. onehundredge(4) -Ethernet port ty…	Enumerationr/w Enumerated Values: -1 invalid 1 fe 2 ge 3 xge 4 onehundredge	.1.3.6.1.4.1.2011.5.14.1.4.1.30
hwifEthernetPortTypeAutoSensing Indicates the switch for the port type auto-sensing. When the switch is enabled, the port will working on GE or FE mode according to that of link partner. Options: 1. enable(1) --enable the port type auto-sensing. 2. …	Enumerationr/w Enumerated Values: -1 invalid 1 enable 2 disable	.1.3.6.1.4.1.2011.5.14.1.4.1.31
hwifEthernetLoopbackTest It used to start loopback test. Options: 1. test(1) -Start loopback test.	Enumerationr/w Enumerated Values: 1 test	.1.3.6.1.4.1.2011.5.14.1.4.1.32
hwifEthernetOfflineReason Indicates the offline reason of ethernet port. Options: 1. invalid(-1) -invalid value 2. unknown(1) -unknown 3. boardabnormal(2) -board abnormal 4. optic…	Enumeration Enumerated Values: -1 invalid 1 unknown 2 boardabnormal 3 opticalmoduleoffline 4 los 5 shutdownbyuser 6 ringdetected 7 ethoamtriggeredlinkdown 8 dyinggasp	.1.3.6.1.4.1.2011.5.14.1.4.1.33
hwifEthernetTxPowerResumeDetect Indicates the switch of Tx auto power resume detection. Options: 1. invalid(-1) -invalid value 2. manual(1) -Tx power resume detection manually 3. auto(2) -Tx power resume detection automatically Default: man…	Enumerationr/w Enumerated Values: -1 invalid 1 manual 2 auto	.1.3.6.1.4.1.2011.5.14.1.4.1.34
hwifEthernetTxPowerDetectInterval Indicates the interval of Tx power pulse. '100-300' means valid value, '-1' means invalid value, Unit: seconds	secondsInteger32r/w Constraints: range: -1--1 range: 100-300	.1.3.6.1.4.1.2011.5.14.1.4.1.35
hwifEthernetTxPowerResumeDuration Indicates the duration of Tx power pulse. '100-3000' means valid value, '-1' means invalid value, Unit: milliseconds	millisecondsInteger32r/w Constraints: range: -1--1 range: 100-3000	.1.3.6.1.4.1.2011.5.14.1.4.1.36
hwifEthernetTxPowerManualResume Indicates the operation of manual resumption. Options: 1. invalid(-1) -invalid value 2. start(1) -start Tx power resumption	Enumerationr/w Enumerated Values: -1 invalid 1 start	.1.3.6.1.4.1.2011.5.14.1.4.1.37
hwifEthernetOpticModuleState Indicates the state of optical module. Options: 1. normal(1) 2. absent(2) 3. abnormal(3) 4. mismatch(4) '2147483647' means invalid value.	Integer32 Constraints: range: 1-4 range: 2147483647-2147483647	.1.3.6.1.4.1.2011.5.14.1.4.1.38
hwifEthernetLinkflapping This object is used for setting the link flapping time of a ETH port 0 indicates disable the ETH port link flapping. 10-5000 indicates enable ETH link flapping. -1: indicates invalid value. Range: -1 0, 10-5000ms,mu…	millisecondInteger32r/w Constraints: range: -1-0 range: 10-5000	.1.3.6.1.4.1.2011.5.14.1.4.1.39
hwifEthernetOfflineTxOffTime Indicates the the offline time on an Ethernet port. Range: -1,0-1000 0-1000: indicates the offline time when link down. 0 means the offline time function is off. -1: indicates invalid value. Default: 0	millisecondInteger32r/w Constraints: range: -1-1000	.1.3.6.1.4.1.2011.5.14.1.4.1.40
hwifEthernetTrafficRateBroadcast Indicates the broadcast traffic suppression on an Ethernet port. Range: -1,0-24414 Unit: pps. 24414: indicates full-suppression of traffic, and 0 indicates no traffic suppression. -1: indicates invalid value. Default:…	Integer32r/w Constraints: range: -1-24414	.1.3.6.1.4.1.2011.5.14.1.4.1.41
hwifEthernetTrafficRateMulticast Indicates the unknown multicast traffic suppression on an Ethernet port. Range: -1,0-24414 Unit: pps. 24414: indicates full-suppression of traffic, and 0 indicates no traffic suppr…	Integer32r/w Constraints: range: -1-24414	.1.3.6.1.4.1.2011.5.14.1.4.1.42
hwifEthernetTrafficRateUnknowncast Indicates the unknown unicast traffic suppression on an Ethernet port. Range: -1,0-24414 Unit: pps. 24414: indicates full-suppression of traffic, and 0 indicates no traffic su…	Integer32r/w Constraints: range: -1-24414	.1.3.6.1.4.1.2011.5.14.1.4.1.43
hwEthernetLightTestTimeduration This object is used to configure the time duration of light test, 0s ~ 3600s, 0s means stopping the testing immidiately.	Integer32r/w Constraints: range: -1-3600	.1.3.6.1.4.1.2011.5.14.1.4.1.44
hwEthernetLightTestTestStatus This object is used to configure the laser test status. Options: 1. enable(1) - laser tx is enable 2. disable(2) - laser tx is disable 3. invalid(-1) - invalid value Default:enable(1).	Enumerationr/w Enumerated Values: -1 invalid 1 enable 2 disable	.1.3.6.1.4.1.2011.5.14.1.4.1.45
hwEthernetLightTestFinshStatus This object is used to configure the laser status after the test is completed. Options: 1. enable(1) - laser tx is enable 2. disable(2) - laser tx is disable 3. original(3) - returned to its original s…	Enumerationr/w Enumerated Values: -1 invalid 1 enable 2 disable 3 original	.1.3.6.1.4.1.2011.5.14.1.4.1.46

Indicates the VLAN trunk feature.
The index of this table is hwifVLANTrunkIndex.

hwifVLANTrunkStatusEntry row .1.3.6.1.4.1.2011.5.14.1.5.1

Indicates the VLAN trunk feature.
The index of this entry is hwifVLANTrunkIndex.

Indexes

hwifVLANTrunkIndex

Column	Syntax	OID
hwifVLANTrunkIndex Vlan trunk index interface index of VLANTrunk	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.14.1.5.1.1
hwifVLANTrunkGvrpRegistration GVRP registration information. Options: 1. normal(1) -This is the default configration. Allow create, register and unretiser vlans dynamiclly at this port. 2. fixed(2) -Allow create and register vlan manully at t…	Enumerationr/w Enumerated Values: 1 normal 2 fixed 3 forbidden	.1.3.6.1.4.1.2011.5.14.1.5.1.2
hwifVLANTrunkPassListLow The low vlan trunk pass list.total vlan includes 8*255= 2040 vlan ids Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 …	OctetString	.1.3.6.1.4.1.2011.5.14.1.5.1.3
hwifVLANTrunkPassListHigh The high vlan trunk pass list. The total vlan includes 8*255= 2040 vlan ids Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying po…	OctetString	.1.3.6.1.4.1.2011.5.14.1.5.1.4
hwifVLANTrunkAllowListLow The low interface of vlan .total interface includes 8*255= 2040 vlan ids Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports …	OctetStringr/w	.1.3.6.1.4.1.2011.5.14.1.5.1.5
hwifVLANTrunkAllowListHigh The high inteface of vlan .total interface includes 8*255= 2040 vlan ids Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports…	OctetStringr/w	.1.3.6.1.4.1.2011.5.14.1.5.1.6

Used to enable or disable the MAC address learning function on S+C traffic streams.
The indexes of this table are hwFrameIndex and hwSlotIndex.

hwBoardMacAddressLearningVlanConnectEntry row .1.3.6.1.4.1.2011.5.14.1.11.1

Used to enable or disable the MAC address learning function on S+C traffic streams.
The indexes of this entry are hwFrameIndex and hwSlotIndex.

Indexes

HUAWEI-DEVICE-MIBhwFrameIndex HUAWEI-DEVICE-MIBhwSlotIndex

Column	Syntax	OID
hwBoardMacAddressLearningVlanConnectCtrl Indicates the status of the the MAC address learning function on S+C traffic streams. Options: 1. invalid(-1) -Indicates that the MAC address learning function on S+C traffic streams is unavailable. 2.…	Enumerationr/w Enumerated Values: -1 invalid 1 disable 2 enable 3 noconfig	.1.3.6.1.4.1.2011.5.14.1.11.1.1

Indicates the line parameter configuration table of an MAC hash conflict. 
It is used to query MAC hash congfig log. 
This table mainly involves configuring parameters such as MacAddress, Vlan, 
Location, DetectedTime, ResolvedTime.
The index of this table is hwMacHashConflictRecordIndex.

hwMacHashConflictRecordEntry row .1.3.6.1.4.1.2011.5.14.1.18.1

Indicates the line parameter configuration table of an MAC hash conflict.
It is used to add, query, modify an MAC hash congfig log.
This table mainly involves configuring parameters such as MacAddress, Vlan,
Location…

Indexes

hwMacHashConflictRecordIndex

Column	Syntax	OID
hwMacHashConflictRecordIndex Indicates the index of the MAC hash conflict, bind MAC hash conflict identification.	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.2011.5.14.1.18.1.1
hwMacHashConflictRecordMacAddress The MAC address of an MAC hash conflict	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2011.5.14.1.18.1.2
hwMacHashConflictRecordVlan The conflict MAC binding vlan ID	Integer32 Constraints: range: 1-4095	.1.3.6.1.4.1.2011.5.14.1.18.1.3
hwMacHashConflictRecordLocation The location of detecting MAC hash conflict	OctetString	.1.3.6.1.4.1.2011.5.14.1.18.1.4
hwMacHashConflictRecordDetectedTime Indicates the time of detecting MAC hash conflict	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2011.5.14.1.18.1.5
hwMacHashConflictRecordResolvedTime Indicates the time of resolving MAC hash conflict	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2011.5.14.1.18.1.6

Indicates the port information extension table, which is used to describe the port 
extension features, such as whether a port is an aggregation port. 
The index of this table is ifIndex.

hwifXXEntry row .1.3.6.1.4.1.2011.5.14.2.1.1

Indicates the port information extension table, which is used to describe the port
extension features, such as whether a port is an aggregation port.
The index of this entry is ifIndex.

Indexes

IF-MIBifIndex

Column	Syntax	OID
hwifAggregatePort whether an Ethernet port is in an aggregation group and whether the port is a master member or slave member. Options: 1. noAggregatePort(1) -Ethernet port is not in an aggregation 2. masterPort(2) -Ethernet port i…	Enumeration Enumerated Values: -1 invalid 1 noAggregatePort 2 masterPort 3 subPort	.1.3.6.1.4.1.2011.5.14.2.1.1.1
hwifMirrorPort Whether it is a mirror port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.14.2.1.1.2
hwifUnknowncastControl Unknown unicast suppression traffic node, in range of (5-100) %	Integer32r/w Constraints: range: 5-100	.1.3.6.1.4.1.2011.5.14.2.1.1.3
hwifMcastControl Broadcast storm suppression, in range of (5-100) %.	Integer32r/w Constraints: range: 5-100	.1.3.6.1.4.1.2011.5.14.2.1.1.4
hwifFlowControl Flow control status	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.14.2.1.1.5
hwifSrcMacControl Whether the source MAC address is being filtered.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.14.2.1.1.6
hwifClearStat Clear port statistics information. Options: 1. clear(1) -In the set operation, clear port statistics information 2. invalid(-1) -In the get operation, the invalid value -1 is returned.	Enumerationr/w Enumerated Values: -1 invalid 1 clear	.1.3.6.1.4.1.2011.5.14.2.1.1.7
hwifLinkStateChangeNum Short duration breaks in the link status	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.5.14.2.1.1.8
hwifLinkUpTime Indicates the time since last link protocol reset/down	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.5.14.2.1.1.9
hwifClearCountTimeStamp Gives the time at which the counters that measure cumulative statistics	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.5.14.2.1.1.10

Indicates the aggregation management table of an Ethernet port. It implements 
dividing multiple Ethernet ports into one aggregation group to realize 
protection and load sharing among ports. After that, protection and load 
sharing can be realized on the ports in an aggregation group.
The index of this table is hwifAggregateIndex.

hwifAggregateEntry row .1.3.6.1.4.1.2011.5.14.2.2.1

Indicates the aggregation management table of an Ethernet port. It implements
dividing multiple Ethernet ports into one aggregation group to realize
protection and load sharing among ports. After that, protection and …

Indexes

hwifAggregateIndex

Column	Syntax	OID
hwifAggregateIndex IfIndex of the master port in an aggregation group.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.14.2.2.1.1
hwifAggregatePortName Setting the description of a link-aggregation group of Ethernet ports. Range: 0-40	OctetStringr/w Constraints: range: 0-40	.1.3.6.1.4.1.2011.5.14.2.2.1.2
hwifAggregatePortListPorts The value of hwifAggregatePortListPorts is an octet string. One bit in each octet indicates one port, so the octet string can indicate eight ports. When a bit is set to 0, it indicates that the corresponding port does …	PortListr/w	.1.3.6.1.4.1.2011.5.14.2.2.1.3
hwifAggregateModel Mode of a link-aggregating group. Options: 1. ingress(1) -load sharing only according to the source MAC 2. ingressEgress(2) -Ingress+egress, load sharing according to source MAC and the destination MAC 3. roundR…	Enumerationr/w Enumerated Values: 1 ingress 2 ingressEgress 3 roundRobin 4 egress 5 mplsLabel 6 srcDstIp 7 ipEnhance	.1.3.6.1.4.1.2011.5.14.2.2.1.4
hwifAggregateRowStatus The present operation status of the row.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.14.2.2.1.5
hwifAggregateWorkMode Workmode of a link-aggregation. Options: 1. manual(1) -manual link aggregation 2. lacpStatic(2) -lacp static link aggregation	Enumerationr/w Enumerated Values: 1 manual 2 lacpStatic	.1.3.6.1.4.1.2011.5.14.2.2.1.6
hwifAggregateOperType Operation type of link-aggregation, use hwifAggregatePortListPorts note to set the port list to be added/deleted in an aggregation group. Options: 1. add(1) -add port(s) to a link-aggregation 2. del(2) -delet…	Enumerationr/w Enumerated Values: -1 invalid 1 add 2 del	.1.3.6.1.4.1.2011.5.14.2.2.1.7
hwifAggregateMaxLinkNum Setting the maximum number of links in an aggregation group. When you add an aggregation group, hwifAggregateMaxLinkNum is optional, If this leaf is not set, the value is 255 by default. Only when hwifAggregateWorkMod…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.2011.5.14.2.2.1.8
hwifAggregateMasterPortIndex IfIndex of the master port in an aggregation group.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.14.2.2.1.9
hwifAggregateLeastLinkNum Setting the least number of links in an aggregation group. When you add an aggregation group, hwifAggregateLeastLinkNum is optional, If this leaf is not set, the value is 255 by default. Only when hwifAggregateWorkMod…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.2011.5.14.2.2.1.10
hwifAggregateHashOption Setting the hash option algorithm of a link-aggregating group. Options: 1. default(1) -Indicates the default route selection algorithm. 2. crc(2) -Indicates that the CRC algorithm is used to calculate packets outgo…	Enumerationr/w Enumerated Values: 1 default 2 crc 3 xor8 4 xor3	.1.3.6.1.4.1.2011.5.14.2.2.1.11
hwifAggregateRandomSeed Setting the random seed value of the link-aggregation group. When you add an aggregation group, hwifAggregateRandomSeed is optional, If this leaf is not set, the value is 0 by default. Range: 0-15 Default: 0	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.2011.5.14.2.2.1.12
hwifAggregateStatus Indicates the forwarding status of the link-aggregation group.	Enumeration Enumerated Values: 1 forwarding 2 block	.1.3.6.1.4.1.2011.5.14.2.2.1.13

Indicates VLAN and the ID list of PVC according to the MAC address.
The index of this table is hwMacAddress.

hwMacToVlanEntry row .1.3.6.1.4.1.2011.5.14.2.3.1

Indicates VLAN and the ID list of PVC according to the MAC address.
The index of this entry is hwMacAddress.

Indexes

hwMacAddress

Column	Syntax	OID
hwMacAddress The MAC learned by the system	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2011.5.14.2.3.1.1
hwInterface the interface index related to the port	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.3.1.2
hwMacToVlanId Mac binding vlan ID	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.3.1.3
hwConnectId the atm pvc connect id of the port if it used as atm interface	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.3.1.4

Ethernet interface mirror table.
The index of this table is hwifEthernetMirrorDstPort.

hwIfEthernetMirrorEntry row .1.3.6.1.4.1.2011.5.14.2.4.1

Ethernet interface mirror table.
The index of this entry is hwifEthernetMirrorDstPort.

Indexes

hwifEthernetMirrorDstPort

Column	Syntax	OID
hwifEthernetMirrorDstPort Destination mirror port, whose format is the same as ifIndex	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.4.1.1
hwifEthernetMirrorSrcPort The mirror port to the source port	PortListr/w	.1.3.6.1.4.1.2011.5.14.2.4.1.2

Table of the FE/GE interface statistics.
An interface containing objects at the
subnetwork layer and below for a particular
interface.
The index of this table is ifIndex.

hwifXStatEntry row .1.3.6.1.4.1.2011.5.14.2.5.1

Table of the FE/GE interface statistics.
An interface containing objects at the
subnetwork layer and below for a particular
interface.
The index of this entry is ifIndex.

Indexes

IF-MIBifIndex

Column	Syntax	OID
hwifInArpPkts The total number of arp packets received on the interface	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.1
hwifInIcmpkts The total number of icmp packets received on the interface	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.2
hwifOutArpPkts The total number of arp packets transmitted out of the interface	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.3
hwifOutIcmpPkts The total number of icmp packets transmitted out of the interface	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.4
hwifOutCRCAlignErrors The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number…	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.5
hwifOutUndersizePkts The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.6
hwifOutOversizePkts The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.7
hwifOutFragments The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error…	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.8
hwifOutJabbers The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or…	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.9
hwifOutCollisions The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) o…	CollisionsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.10
hwifOutPkts64Octets The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.11
hwifOutPkts65to127Octets The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.12
hwifOutPkts128to255Octets The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.13
hwifOutPkts256to511Octets The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.14
hwifOutPkts512to1023Octets The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.15
hwifOutPkts1024to1518Octets The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.16
hwifInCRCAlignErrors The total number of packets send that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number of …	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.17
hwifInUndersizePkts The total number of packets send that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.18
hwifInOversizePkts The total number of packets send that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.19
hwifInFragments The total number of packets send that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or…	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.20
hwifInJabbers The total number of packets send that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a b…	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.21
hwifInPkts64Octets The total number of packets (including bad packets) send that were 64 octets in length (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.22
hwifInPkts65to127Octets The total number of packets (including bad packets) send that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.23
hwifInPkts128to255Octets The total number of packets (including bad packets) send that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.24
hwifInPkts256to511Octets The total number of packets (including bad packets) send that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.25
hwifInPkts512to1023Octets The total number of packets (including bad packets) send that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.26
hwifInPkts1024to1518Octets The total number of packets (including bad packets) send that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.5.1.27

Indicates the board bonding table. It is used for setting the bonding between boards. 
In addition, it supports the query of the status of the interconnected ports on bound 
boards. When you need to bind two boards or query the status of the interconnected 
ports on either board, use this table. The bound boards can be configured with inter-board 
aggregation and service configuration commands are delivered to the two boards.
The index of this table is hwBindBrdFSIndex.

hwBoardBindEntry row .1.3.6.1.4.1.2011.5.14.2.6.1

Indicates the board bonding table. It is used for setting the bonding between boards.
In addition, it supports the query of the status of the interconnected ports on bound
boards. When you need to bind two boards or q…

Indexes

hwBindBrdFSIndex

Column	Syntax	OID
hwBindBrdFSIndex Ifindex of bound board in left slot.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.14.2.6.1.1
hwBindBrdAnotherFSIndex Ifindex of bound board in right slot.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.6.1.2
hwLeftBrdLinkStatus Link status of bound board in left slot. 1:link up 2:link down 2: default	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.6.1.3
hwRightBrdLinkStatus Link status of bound board in right slot. 1:link up 2:link down 2: default	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.6.1.4
hwBoardBindRowStatus The present operation status of the row.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.14.2.6.1.5
hwLeftBrdPrimaryStatus The primary status of the Board. This parameter indicates the current overall service condition of an entity, i.e., whether it is in-service or out-of-service. Options: 1. isNr(1) - In service, normal 2. isAnr(2) …	Enumeration Enumerated Values: 1 isNr 2 isAnr 3 isRst 4 isAnrst 5 oosAu 6 oosMa 7 oosAuma 8 oosAurst 9 oosMaanr	.1.3.6.1.4.1.2011.5.14.2.6.1.6
hwLeftBrdSecondaryStatus This parameter indicates the secondary status of the board. The parameter provides additional information pertaining to PST and PSTQ. For example, it may indicate the type and/or reason of the external command, the even…	Bits Enumerated Values: 0 sstAins 1 sstFaf 2 sstFlt 3 sstLpbk 4 sstMea 5 sstSgeo 6 sstStbyh 7 sstTs 8 sstUas 9 sstUeq 10 sstWrk 11 sstPwr	.1.3.6.1.4.1.2011.5.14.2.6.1.7
hwRightBrdPrimaryStatus The primary status of the Board. This parameter indicates the current overall service condition of an entity, i.e., whether it is in-service or out-of-service. Options: 1. isNr(1) - In service, normal 2. isAnr(2) …	Enumeration Enumerated Values: 1 isNr 2 isAnr 3 isRst 4 isAnrst 5 oosAu 6 oosMa 7 oosAuma 8 oosAurst 9 oosMaanr	.1.3.6.1.4.1.2011.5.14.2.6.1.8
hwRightBrdSecondaryStatus This parameter indicates the secondary status of the board. The parameter provides additional information pertaining to PST and PSTQ. For example, it may indicate the type and/or reason of the external command, the even…	Bits Enumerated Values: 0 sstAins 1 sstFaf 2 sstFlt 3 sstLpbk 4 sstMea 5 sstSgeo 6 sstStbyh 7 sstTs 8 sstUas 9 sstUeq 10 sstWrk 11 sstPwr	.1.3.6.1.4.1.2011.5.14.2.6.1.9

Interface Vlan Loop table entry
The index of this table is hwVlanLoopIndex

hwVlanLoopEntry row .1.3.6.1.4.1.2011.5.14.2.7.1

Interface Vlan Loop table entry
The index of this entry is hwVlanLoopIndex

Indexes

hwVlanLoopIndex

Column	Syntax	OID
hwVlanLoopIndex Indicates the vlan loop index, a unique value to identify the vlan loop. Recently, the index value can only be fixed to 1.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.7.1.1
hwVlanLoopSrcIfIndex Source vlan loop port, whose format is the same as ifIndex	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.7.1.2
hwVlanLoopSrcOuterVlanId The outer vlan id of the source port , the bound of parameter is 1 to 4095	Integer32r/w Constraints: range: 1-4095	.1.3.6.1.4.1.2011.5.14.2.7.1.3
hwVlanLoopSrcInnerVlanId The inner vlan id of the source port , the bound of patameter is 1 to 4095	Integer32r/w Constraints: range: 1-4095	.1.3.6.1.4.1.2011.5.14.2.7.1.4
hwVlanLoopDstIfIndex The destination vlan loop port, whose format is the same as ifIndex	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.7.1.5
hwVlanLoopDstOuterVlanId The outer vlan id of the destination port , the bound of patameter is 1 to 4095	Integer32r/w Constraints: range: 1-4095	.1.3.6.1.4.1.2011.5.14.2.7.1.6
hwVlanLoopDstInnerVlanId The inner vlan id of the destination port , the bound of patameter is 1 to 4095	Integer32 Constraints: range: 1-4095	.1.3.6.1.4.1.2011.5.14.2.7.1.7
hwVlanLoopTimeout The remain time of the vlan loop before stopped. Recently, this leaf is not supported. Unit: second	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.7.1.8
hwVlanLoopRowStatus Indicates the row status. To create vlan loop, set this leaf to createAndGo(4). To delete vlan loop, set this leaf to destroy(6). When this leaf is queried, the value is fixed to active(1). Options: 1. active(1) …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.14.2.7.1.9

A collection of statistics kept for an aggregation.
The value of statistics is the sum of all etherports under an aggregation.
The index of this table is hwAggStatsIndex.

hwAggregateStatisticsEntry row .1.3.6.1.4.1.2011.5.14.2.9.1

A collection of statistics kept for an aggregation.
The value of statistics is the sum of all etherports under an aggregation.
The index of this entry is hwAggStatsIndex.

Indexes

hwAggStatsIndex

Column	Syntax	OID
hwAggStatsIndex The value of this object(ifindex) uniquely identifies this aggregate entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.9.1.1
hwAggStatsDropEvents The total number of events in which packets were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has b…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.2
hwAggStatsRecvOctets The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets). '18446744073709551615' means invalid value.	OctetsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.3
hwAggStatsSendOctets The total number of octets of data (including those in bad packets) sent on the network (excluding framing bits but including FCS octets). '18446744073709551615' means invalid value.	OctetsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.4
hwAggStatsTotalOctets The total number of octets of data (including those in bad packets) on the network (excluding framing bits but including FCS octets). '18446744073709551615' means invalid value.	OctetsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.5
hwAggStatsRecvPkts The total number of packets (including bad packets, broadcast packets, and multicast packets) received. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.6
hwAggStatsSendPkts The total number of packets (including bad packets, broadcast packets, and multicast packets) sent. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.7
hwAggStatsTotalPkts The total number of packets (including bad packets, broadcast packets, and multicast packets). '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.8
hwAggStatsBroadcastRecvPkts The total number of good packets received that were directed to the broadcast address. Note that this does not include multicast packets. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.9
hwAggStatsBroadcastSendPkts The total number of good packets send that were directed to the broadcast address. Note that this does not include multicast packets. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.10
hwAggStatsBroadcastTotalPkts The total number of good packets that were directed to the broadcast address. Note that this does not include multicast packets. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.11
hwAggStatsMulticastRecvPkts The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.12
hwAggStatsMulticastSendPkts The total number of good packets sent that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.13
hwAggStatsMulticastTotalPkts The total number of good packets that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.14
hwAggStatsCRCAlignErrors The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number…	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.15
hwAggStatsUndersizePkts The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.16
hwAggStatsOversizePkts The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.17
hwAggStatsFragments The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error…	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.18
hwAggStatsJabbers The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or…	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.19
hwAggStatsCollisions The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) o…	CollisionsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.20
hwAggStatsPkts64Octets The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets). '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.21
hwAggStatsPkts65to127Octets The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets). '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.22
hwAggStatsPkts128to255Octets The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets). '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.23
hwAggStatsPkts256to511Octets The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets). '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.24
hwAggStatsPkts512to1023Octets The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets). '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.25
hwAggStatsPkts1024to1518Octets The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets). '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.26
hwAggStatsPkts1519to2047Octets Total number of frames of 1519-2047 bytes. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.27
hwAggStatsPkts2048to4095Octets Total number of frames of 2048-4095 bytes. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.28
hwAggStatsPkts4096to9216Octets Total number of frames of 4096-9216 bytes. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.29
hwAggStatsPktsRecvPauseInfo Number of PAUSE frames received by the port. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.30
hwAggStatsPktsSendPauseInfo Number of PAUSE frames send from the port. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.31
hwAggStatsPktsSendSingleCollisionInfo The total number of packets sent correctly after a single collision. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.32
hwAggStatsPktsSendMultiCollisionInfo The total number of packets sent correctly after multiple collisions. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.33
hwAggStatsUpDiscardPacketsInfo The total number of up stream discarded packets. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.34
hwAggStatsDownDiscardPacketsInfo The total number of down stream discarded packets. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.35
hwAggStatsAlignmentErrorFramesInfo The total number of alignment error frames. '18446744073709551615' means invalid value.	FramesSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.36
hwAggStatsSpeed The total speed of Aggregate ports.	KbpsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.5.14.2.9.1.37
hwAggStatsOutboundErrors The total number of outbound packets that could not be transmitted because of errors. '18446744073709551615' means invalid value.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.14.2.9.1.38
hwAggStatsClear Clear aggregate port statistics information. Options: 1. clear(1) -In the set operation, clear port statistics information 2. invalid(-1) -In the get operation, the invalid value -1 is returned.	Enumerationr/w Enumerated Values: -1 invalid 1 clear	.1.3.6.1.4.1.2011.5.14.2.9.1.100

Indicates the speed mode of the board.
The index of this table is hwFrameIndex and hwSlotIndex.

hwBoardSpeedModeEntry row .1.3.6.1.4.1.2011.5.14.2.10.1

Indicates the speed mode of the board.
The index of this entry is hwFrameIndex and hwSlotIndex.

Indexes

HUAWEI-DEVICE-MIBhwFrameIndex HUAWEI-DEVICE-MIBhwSlotIndex

Column	Syntax	OID
hwBoardSpeedMode The speed mode of the board. Options: 1: port 0-7 GE(1) 2: port 0-7 10GE(2) 3: port 0-3 GE, port 4-7 10GE(3) Default: port 0-7 GE(1).	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.10.1.1

This table is used to manage the configuration information of an aggregation group loadbalancing.
The index of this table is hwAggLBConfigIndex.

hwAggLoadbalancingConfigEntry row .1.3.6.1.4.1.2011.5.14.2.13.1

This table is used to manage the configuration information of an aggregation group loadbalancing.
The index of this entry is hwAggLBConfigIndex.

Indexes

hwAggLBConfigIndex

Column	Syntax	OID
hwAggLBConfigIndex IfIndex of the master port in an aggregation group.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.13.1.1
hwAggLBSrcMacAddress The source MAC address of the packet. The following is an example of the input format of the MAC address: If the MAC address is 00e0-fc11-0000, enter # 0x00 0xe0 0xfc 0x11 0x00 0x00 or the character string 00-e0-fc-11-…	OctetStringr/w Constraints: range: 6-17	.1.3.6.1.4.1.2011.5.14.2.13.1.2
hwAggLBDstMacAddress The destination MAC address of the packet. The following is an example of the input format of the MAC address: If the MAC address is 00e0-fc11-0000, enter # 0x00 0xe0 0xfc 0x11 0x00 0x00 or the character string 00-e0-f…	OctetStringr/w Constraints: range: 6-17	.1.3.6.1.4.1.2011.5.14.2.13.1.3
hwAggLBIpAddressType Indicates the IP address type. Options: 1. ipv4(1) -indicates that the IP address type is ipv4 2. ipv6(2) -indicates that the IP address type is ipv6	Enumerationr/w Enumerated Values: 1 ipv4 2 ipv6	.1.3.6.1.4.1.2011.5.14.2.13.1.4
hwAggLBProtocol The protocol of the IP packets. Range: 0-255 The common types include: ICMP: indicates the Internet Control Message Protocol with protocol ID 1 IGMP: indicates the Internet Group manageme…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.2011.5.14.2.13.1.5
hwAggLBSrcIpAddress The source IPv4 address of the packet.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.2011.5.14.2.13.1.6
hwAggLBDstIpAddress The destination IPv4 address of the packet.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.2011.5.14.2.13.1.7
hwAggLBSrcIpv6Address The source IPv6 address of the packet.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2011.5.14.2.13.1.8
hwAggLBDstIpv6Address The destination IPv6 address of the packet.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2011.5.14.2.13.1.9
hwAggLBSrcPort The specify source port of the packet. Range: 0-65535	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2011.5.14.2.13.1.10
hwAggLBDstPort The specify destination port of the packet. Range: 0-65535	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2011.5.14.2.13.1.11
hwAggLBInportIndex IfIndex of the input port.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.5.14.2.13.1.12

This table is used to get the result of the packet selection port for an aggregation group.
The index of this table is hwAggLBIndex.

hwAggLoadbalancingEntry row .1.3.6.1.4.1.2011.5.14.2.14.1

This table is used to get the result of the packet selection port for an aggregation group.
The index of this entry is hwAggLBIndex.

Indexes

hwAggLBIndex

Column	Syntax	OID
hwAggLBIndex IfIndex of the master port in an aggregation group.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.14.1.1
hwAggLBSelectIndex The result of the packet selection port for an aggregation group.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.2.14.1.2

Indicates the port information of an aggregation group. 
The indexes of this table are hwAggregateIndex and hwAggregatePortIndex.

hwAggregatePortEntry row .1.3.6.1.4.1.2011.5.14.2.15.1

Indicates the port information of an aggregation group.
The indexes of this entry are hwAggregateIndex and hwAggregatePortIndex.

Indexes

hwAggregateIndex hwAggregatePortIndex

Column	Syntax	OID
hwAggregateIndex IfIndex of the master port in an aggregation group.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.14.2.15.1.1
hwAggregatePortIndex IfIndex of the port in an aggregation group.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.14.2.15.1.2
hwAggregatePortStatus Indicates the forwarding status of port in an aggregation group. Options: 1. forwarding(1) -Indicates that the forwarding status of the port in an aggregation group is forwarding. 2. block(2) -Indicates that the …	Enumeration Enumerated Values: 1 forwarding 2 block	.1.3.6.1.4.1.2011.5.14.2.15.1.3

Indicates the table that contains certain extended attributes of a service flow.
The index of this table is hwIpdslamConnectIndex.

hwIpdslamConnectEntry row .1.3.6.1.4.1.2011.5.14.3.1.1

Indicates the table that contains certain extended attributes of a service flow.
The index of this entry is hwIpdslamConnectIndex.

Indexes

hwIpdslamConnectIndex

Column	Syntax	OID
hwIpdslamConnectIndex For the broadband service, this leaf is the same as hwExtSrvFlowIndex, which indicates the service flow index, a unique value to identify a service flow.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.1.1.1
hwIpdslamConnectFlowControl Enable/disable the connection flow control, and the source destination direction is determined by the direction created by PVC. The connect flow control. Options: 1. bothOff(1) -The value is not support…	Enumerationr/w Enumerated Values: 1 bothOff 2 srcDown 3 dstDown 4 srcDownAndDstDown 5 srcUp 6 srcBoth 7 srcUpAndDstDown 8 srcBothAndDstDown 9 dstUp 10 dstUpAndSrcDown 11 dstBoth 12 dstBothAndSrcDown 13 dstUpAndSrcUp 14 dstUpAndSrcBoth 15 dstBothAndSrcUp 16 dstBothAndSrcBoth	.1.3.6.1.4.1.2011.5.14.3.1.1.2
hwIpdslamConnectMaxMacLearn Indicates the maximum number of learnable MAC addresses of the service port. Due to different hardware capabilities, the ports of different types support different value ranges. The ATM or xDSL port supports the range …	Integer32r/w Constraints: range: -1-1023	.1.3.6.1.4.1.2011.5.14.3.1.1.3
hwIpdslamConnectMacLearnd The number of MACs this connection has learned.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.1.1.4
hwIpdslamConnectPriorityLevel The priority of this connection. Options: 1. high(1) -The value is not supported. 2. low(2) -The value is not supported. Before the priority function is enabled in LAN, the order of priority for each connection in …	Enumerationr/w Enumerated Values: 1 high 2 low	.1.3.6.1.4.1.2011.5.14.3.1.1.5
hwIpdslamConnectSrcVportPhysical The source virtual physical port of this connection. The port can't be bigger than or equal to 65535.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.1.1.6
hwIpdslamConnectDstVportPhysical The destination virtual physical port of this connection. The port can't be bigger than or equal to 65535.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.1.1.7
hwIpdslamConnectInnerVlanId Indicates the network-side inner VLAN ID of switch-oriented service flow. The value of this leaf is variable with the value of hwExtSrvFlowTagTransform. If the value of hwExtSrvFlowTagTransform is set to 3, 4, 5, this l…	Integer32r/w Constraints: range: -1-4095	.1.3.6.1.4.1.2011.5.14.3.1.1.8
hwIpdslamConnectInnerVlanPriority Indicates the network-side inner VLAN priority of switch-oriented service flow. The value of this leaf is variable with the value of hwExtSrvFlowTagTransform. If the value of hwExtSrvFlowTagTransform is set to 3, 4, 5, …	Integer32r/w Constraints: range: 0-7 range: 255-255	.1.3.6.1.4.1.2011.5.14.3.1.1.9
hwIpdslamConnectMulticastForwardingMode The flag of Multicast forwarding mode on service board. Options: 1. outervlan(1) -Indicates outer VLAN. 2. outervlanInnervlan(2) -Indicates outer VLAN and inner VLAN.	Enumerationr/w Enumerated Values: 1 outervlan 2 outervlanInnervlan	.1.3.6.1.4.1.2011.5.14.3.1.1.10

Used for binding an IP address to a service port. To statically configure the permitted IP address of 
a service port, use this table.
After the IP address is bound to a service port successfully, the device allows only the upstream packets 
whose source IP address is the bound IP address to pass.
The indexes of this table are hwIpdslamBindIpConnectIndex and hwIpdslamBindIpSubIndex, indicating the index of the service port. 
The service port corresponding to this index must already be created in hwExtSrvFlowEntry.
hwIpdslamBindIpSubIndex is the index used for specifying the position on the service port for binding the 
IP address.

hwIpdslamBindIpEntry row .1.3.6.1.4.1.2011.5.14.3.2.1

Used for binding an IP address to a service port. To statically configure the permitted IP address of
a service port, use this table.
After the IP address is bound to a service port successfully, the device allows only…

Indexes

hwIpdslamBindIpConnectIndex hwIpdslamBindIpSubIndex

Column	Syntax	OID
hwIpdslamBindIpConnectIndex Indicates the index of the service port bound to a specified IP address. The service port corresponding to this index must already be created in hwExtSrvFlowEntry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.2.1.1
hwIpdslamBindIpSubIndex This index is used for specifying the position on the service port for binding the IP address. hwIpdslamBindIpSubIndex is filled with -1, all IP addresses of the service port are deleted.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.2.1.2
hwIpdslamBindIpAddress Indicates the IP address bound to a specified service port.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.2011.5.14.3.2.1.3
hwIpdslamBindIpAddressRowStatus Indicates the row status. Options: 1. active(1) 2. createAndGo(4) 3. destroy(6) During creation, hwIpdslamBindIpSubIndex may not be specified and can be automatically allocated by the system. In this case, you can fil…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.14.3.2.1.4
hwIpdslamBindIpAddressType Indicates the IP address type to bind. Options: 1. ipv4(1) -indicates that the IP address type is ipv4 2. ipv6(2) -indicates that the IP address type is ipv6 During creation, if hwIpdslamBindIpAddressType is not spe…	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.2011.5.14.3.2.1.5
hwIpdslamBindIpv6Address Indicates the IPv6 address bound to a specified service port. It must be a valid unicast IPv6 address.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2011.5.14.3.2.1.6
hwIpdslamBindIpv6PrefixLength Indicates the prefix length of the IPv6 address bound to a specified service port. i.e. Valid value only includes 48,56,60,64 and 128.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.5.14.3.2.1.7
hwIpdslamBindIpMaskLength Indicates the Mask length of the IPv4 address bound to a specified service port. Range: 17-32. The invalid value is 4294967295.	Unsigned32r/w Constraints: range: 17-32 range: 4294967295-4294967295	.1.3.6.1.4.1.2011.5.14.3.2.1.8

Indicates MAC address binding feature.
The indexes of this table are hwIpdslamBindMacConnectIndex and hwIpdslamBindMacSubIndex.

hwIpdslamBindMacEntry row .1.3.6.1.4.1.2011.5.14.3.3.1

Indicates MAC address binding feature.
The indexes of this entry are hwIpdslamBindMacConnectIndex and hwIpdslamBindMacSubIndex.

Indexes

hwIpdslamBindMacConnectIndex hwIpdslamBindMacSubIndex

Column	Syntax	OID
hwIpdslamBindMacConnectIndex Bind MAC address connect identification	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.3.1.1
hwIpdslamBindMacSubIndex Bind MAC address sub index	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.3.1.2
hwIpdslamBindMacAddress The MAC address to bind	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2011.5.14.3.3.1.3
hwIpdslamBindMacAddressRowStatus Bind MAC address operate (add(4),delete(6))	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.14.3.3.1.4

Indicates the IP traffic profile. 
It is used to add, query, modify, or delete an IP traffic profile. 
This table mainly involves configuring CAR parameters such as CIR, PIR, 
CBS, and PBS and re-marking priority. 
The index of this table is hwIpTrafficIndex.

hwIpTrafficParamEntry row .1.3.6.1.4.1.2011.5.14.3.8.1

Indicates the IP traffic profile.
It is used to add, query, modify, or delete an IP traffic profile.
This table mainly involves configuring CAR parameters such as CIR, PIR,
CBS, and PBS and re-marking priority.
The …

Indexes

hwIpTrafficIndex

Column	Syntax	OID
hwIpTrafficIndex Indicates the table index. Range: 1-1024, -1 When creating an IP traffic profile, you can specify or not specify a profile index. If you specify it to 4294967295, the system will automatically allocates an idle index. …	Integer32 Constraints: range: -1--1 range: 1-1024	.1.3.6.1.4.1.2011.5.14.3.8.1.1
hwIpTrafficName Indicates the traffic table name. Each IP traffic profile has a unique name. When creating an IP traffic profile, you can specify or not specify a profile name. If you do not specify it, the system automatically gene…	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.2011.5.14.3.8.1.2
hwIpTrafficCir Indicates the committed information rate (CIR). Range: -1, 0-10240000 kbit/s. Unit: kbit/s. CIR is a mandatory parameter. This parameter must be an integer multiple of 64. If the entered value is not an integer multip…	Integer32r/w Constraints: range: -1-10240000	.1.3.6.1.4.1.2011.5.14.3.8.1.3
hwIpTrafficCbs Indicates the committed burst size (CBS). Range: -1, 0-1024000000 bytes. Unit: bytes. CBS is an optional parameter. If the parameter is not specified, it can be obtained by formula min(2000+cir*32,1024000000). For boa…	Integer32r/w Constraints: range: -1-1024000000	.1.3.6.1.4.1.2011.5.14.3.8.1.4
hwIpTrafficPir Indicates the peak information rate (PIR). Range: -1, 64-10240000 kbit/s. Unit: kbit/s. PIR is an optional parameter. If the parameter is not specified, it can be obtained through formula max(min(2*cir,10240000),64). …	Integer32r/w Constraints: range: -1--1 range: 64-10240000	.1.3.6.1.4.1.2011.5.14.3.8.1.5
hwIpTrafficPbs Indicates the peak burst size (PBS). Range: -1, 2000-1024000000 bytes. Unit: bytes. PBS is an optional parameter.If the parameter is not specified, it can be obtained by formula min(2000+32*pir,1024000000). -1 indicat…	Integer32r/w Constraints: range: -1--1 range: 2000-1024000000	.1.3.6.1.4.1.2011.5.14.3.8.1.6
hwIpTrafficCm Indicates the color-aware mode of the IP traffic profile. Options: 1. colorBlind(1) -Indicates color blind mode. 2. colorAware(2) -Indicates color aware mode.	Enumerationr/w Enumerated Values: 1 colorBlind 2 colorAware	.1.3.6.1.4.1.2011.5.14.3.8.1.7
hwIpTrafficPriority Indicates the outer priority of the IP traffic profile. The higher 16 bits indicate the outer priority mapping policy and the lower 16 bits indicate the outer priority. The outer priority storage mode of the IP traffi…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.8.1.8
hwIpTrafficPriorityPolicy Indicates the queue-joining trust priority policy of the IP traffic profile. Options: 1. localPriority(1) -Indicates the queue-joining trust the priority set by IP traffic profile. 2. egressOuter802dot1p(…	Enumerationr/w Enumerated Values: 1 localPriority 2 egressOuter802dot1p 3 inner802dot1p 4 ingressOuter802dot1p 5 queuePolicyProfile	.1.3.6.1.4.1.2011.5.14.3.8.1.9
hwIpTrafficRowStatus Indicates the row status. Options: 1. active(1) 2. createAndGo(4) 3. destroy(6) To create an IP traffic profile, set this leaf to createAndGo(4); to delete an IP traffic profile, set this leaf to destroy(6). When …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.14.3.8.1.10
hwIpTrafficInnerPriority Indicates the inner priority of the IP traffic profile. The higher 16 bits indicate the inner priority mapping policy and the lower 16 bits indicate the inner priority. The inner priority storage mode of the IP traffi…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.8.1.11
hwIpTrafficInnerPriorityMappingIndex When the inner VLAN priority mapping policy is mapping from the outer or inner CoS domain on the ingress, the index (range: 1-4) of the service port priority mapping profile is used. The referenced service port priori…	Integer32r/w Constraints: range: -1--1 range: 1-4	.1.3.6.1.4.1.2011.5.14.3.8.1.12
hwIpTrafficPriorityMappingIndex When the outer VLAN priority mapping policy is mapping from the outer or inner CoS domain on the ingress, the index (range: 1-4) of the service port priority mapping profile is used. The referenced service port priori…	Integer32r/w Constraints: range: -1--1 range: 1-4	.1.3.6.1.4.1.2011.5.14.3.8.1.13
hwIpTrafficColorPolicy Indicates the color policy of the IP traffic profile. Options: 1. dei(1) -Indicate the dei mode. 2. cos(2) -Indicate the CoS mode.	Enumerationr/w Enumerated Values: 1 dei 2 cos	.1.3.6.1.4.1.2011.5.14.3.8.1.14
hwIpTrafficCarThresholdProfileIndex Indicates the car-threshold profile of the IP traffic profile	Integer32r/w Constraints: range: -1--1 range: 1-4	.1.3.6.1.4.1.2011.5.14.3.8.1.15
hwIpTrafficFixBandWidth Indicates the fixed bandwidth to be allocated by the DBA. This parameter takes effect to the E2E service flow only on a GPON board. Range: -1, 0-10240000 kbit/s. Unit: kbit/s. hwIpTrafficFixBandWidth must be smaller tha…	Integer32r/w Constraints: range: -1-10240000	.1.3.6.1.4.1.2011.5.14.3.8.1.16
hwIpTrafficCouplingFlag The Coupling Flag CF is set to either 0 or 1. The choice of the value for CF has the effect of controlling the volume of the yellow Service Frames admitted to the network. When CF is set to 0, the long term average bit…	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.2011.5.14.3.8.1.17
hwIpTrafficDSCP Indicates the DSCP source. The most significant 16 bits indicate the DSCP policy, and the least significant 16 bits indicate the DSCP value. -------------------------------------------------------- | …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.8.1.18
hwIpTrafficDSCPMappingIndex Indicates the index of the referenced DSCP mapping profile. When the hwIpTrafficDSCP is set to user-dscp(OxFE), the mapping profile index must be set to a valid profile. When the hwIpTrafficDSCP is not set to user-dscp…	Integer32r/w Constraints: range: -1--1 range: 1-4	.1.3.6.1.4.1.2011.5.14.3.8.1.19
hwIpTrafficDropPrecedence Indicates the packet discarding policy. Options: 1. invalid(-1) -indicates that this function is not supported. 2. remarkedOuterPriority(0) -indicates that the internal packet discarding priority is the priority o…	Enumerationr/w Enumerated Values: -1 invalid 0 remarkedOuterPriority 1 remarkedInnerPriority	.1.3.6.1.4.1.2011.5.14.3.8.1.20
hwIpTrafficColorDEI Indicates the color mark. It indicates whether and where the color is marked. Options: 1. unmarkDei(0) -indicates that the color is not marked. 2. outerDei(1) -indicates that the color is marked on the outer …	Enumerationr/w Enumerated Values: 0 unmarkDei 1 outerDei 2 innerDei 3 outerInnerDei	.1.3.6.1.4.1.2011.5.14.3.8.1.21
hwIpTrafficColorSource Indicates the color source. It indicates where the color is marked. Default: outerDei(1). Options: 1. invalid(-1) -invalid value. 2. outerDei(1) -indicates that the color is marked on the outer VLAN's DEI. 3.…	Enumerationr/w Enumerated Values: -1 invalid 1 outerDei 2 innerDei	.1.3.6.1.4.1.2011.5.14.3.8.1.22
hwIpTrafficE2EPriority Indicates the e2e priority of the IP traffic profile. The higher 16 bits indicate the outer priority mapping policy and the lower 16 bits indicate the e2e priority. The e2e priority storage mode of the IP traffic prof…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.8.1.23
hwIpTrafficE2EPriorityMappingIndex When the e2e VLAN priority mapping policy is mapping from the outer CoS domain on the ingress, the index (range: 1-16) of the service port priority mapping profile is used. The referenced service port priority mapping…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.8.1.24
hwIpTrafficRateProfileName Indicates the name of the rate profile.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.5.14.3.8.1.25
hwIpTrafficQueuePolicyProfileIndex Indicates the index of the queue policy profile. Range: 1-4	Integer32r/w Constraints: range: -1--1 range: 1-4	.1.3.6.1.4.1.2011.5.14.3.8.1.26
hwIpTrafficPriorityGroupProfileName Indicates the name of the priority group profile.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.5.14.3.8.1.27
hwIpTrafficWrrWeightYellow Indicates the WRR weight for yellow color packet. Range: 0, 1-12 Default: 0 0 indicates WRR weight is auto calculated by PIR and CIR.	Integer32r/w Constraints: range: 0-12	.1.3.6.1.4.1.2011.5.14.3.8.1.28
hwIpTrafficWrrWeightGreen Indicates the WRR weight for green color packet. Range: 0, 1-12 Default: 0 0 indicates WRR weight is auto calculated by PIR and CIR.	Integer32r/w Constraints: range: 0-12	.1.3.6.1.4.1.2011.5.14.3.8.1.29

Indicates the CAR mode. It is used to modify and query the board CAR mode and does not support the 
create or delete operation. Before the CAR mode of a board is modified, the board cannot have any
service port or port CAR configuration. When the CAR mode of a board is modified, hwFrameIndex and 
hwSlotIndex must be specified and leaf hwBoardTrafficModeType must be issued.
The indexes of this table are hwFrameIndex and hwSlotIndex.

hwBoardTrafficModeEntry row .1.3.6.1.4.1.2011.5.14.3.9.1

Indicates the CAR mode. It is used to modify and query the board CAR mode and does not support the
create or delete operation. Before the CAR mode of a board is modified, the board cannot have any
service port or port …

Indexes

HUAWEI-DEVICE-MIBhwFrameIndex HUAWEI-DEVICE-MIBhwSlotIndex

Column	Syntax	OID
hwBoardTrafficModeType Indicates the board CAR mode. It can be flow CAR or port+CoS CAR. If the board supports the port CAR mode, this leaf is used to configure the port CAR mode in batches for all ports. The port CAR mode is set by hwPortC…	Enumerationr/w Enumerated Values: -1 invalid 1 servicePort 2 portCos	.1.3.6.1.4.1.2011.5.14.3.9.1.1

Indicates the port+CoS CAR table. It is used to add, query, modify, or delete the IP traffic 
profile used by the port+CoS CAR. The indexes of this table are ifIndex, hwCosPortExtPara1, 
hwCosPortOntId, hwCosPortGemIndex and hwCosPortTrafficCos. The port+CoS CAR can be set only 
when the board CAR mode is portCos(2). When querying or modifying the port+CoS CAR, you must 
enter both the IP traffic profiles used by the upstream traffic and downstream traffic (either 
the names or indexes of the upstream and downstream IP traffic profiles can be entered).

hwCosPortTrafficEntry row .1.3.6.1.4.1.2011.5.14.3.10.1

Indicates the port+CoS CAR table. It is used to add, query, modify, or delete the IP traffic
profile used by the port+CoS CAR. The indexes of this entry are ifIndex, hwCosPortExtPara1,
hwCosPortOntId, hwCosPortGemInde…

Indexes

IF-MIBifIndex hwCosPortExtPara1 hwCosPortOntId hwCosPortGemIndex hwCosPortTrafficCos

Column	Syntax	OID
hwCosPortTrafficCos It is one of table indexes. Its meaning varies with the value range. When the value range is 0-7, it indicates the priority for the specified CoS field of packets.When the value range is 8-15, it indicates the index fo…	Integer32 Constraints: range: 0-15	.1.3.6.1.4.1.2011.5.14.3.10.1.1
hwCosPortInboundTrafficIndex Indicates the index of the IP traffic profile used by upstream packets. Range: 1-1024 The IP traffic profile indicated by this index must exist in hwIpTrafficParamTable.	Integer32r/w Constraints: range: 1-1024	.1.3.6.1.4.1.2011.5.14.3.10.1.2
hwCosPortOutboundTrafficIndex Indicates the index of the IP traffic profile used by downstream packets. Range: 1-1024 The IP traffic profile indicated by this index must exist in hwIpTrafficParamTable.	Integer32r/w Constraints: range: 1-1024	.1.3.6.1.4.1.2011.5.14.3.10.1.3
hwCosPortTrafficRowStatus Indicates the row status. In creation, you must set this leaf to createAndGo(4) and must enter both the IP traffic profiles used by the upstream traffic and downstream traffic (either the names or indexes of the upstr…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.14.3.10.1.4
hwCosPortExtPara1 It is one of table indexes. It is a difference parameter between access modes, indicating the GEM port ID. This leaf is valid when the GPON board works in the distributing mode and invalid in other cases. Value -1 ind…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.14.3.10.1.5
hwCosPortInboundTrafficName Indicates the name of the IP address used by upstream packets. The IP traffic profile indicated by this name must exist in hwIpTrafficParamTable.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.5.14.3.10.1.6
hwCosPortOutboundTrafficName Indicates the name of the IP address used by downstream packets. The IP traffic profile indicated by this name must exist in hwIpTrafficParamTable.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.5.14.3.10.1.7
hwCosPortOntId It is one of table indexes. It is a difference parameter between access modes, indicating the ONT ID. Range: -1, 0-255 This leaf is valid when the GPON works in the profile mode or when the board is an EPON board. In o…	Integer32 Constraints: range: -1-255	.1.3.6.1.4.1.2011.5.14.3.10.1.8
hwCosPortGemIndex It is one of table indexes. It is a difference parameter between access modes, indicating the GEM index. Range: -1, 0-1023 This leaf is valid when the GPON board works in the profile mode and invalid in other cases. V…	Integer32 Constraints: range: -1-1023	.1.3.6.1.4.1.2011.5.14.3.10.1.9
hwCosPortCosGroupTableIndex It indicates the index of the CoS-group table bound to the GEM port. Range: -1 | 1-16 The value -1 indicates that this leaf is invalid.	Integer32 Constraints: range: -1--1 range: 1-16	.1.3.6.1.4.1.2011.5.14.3.10.1.10