HP-ICF-IPCONFIG Table View

This table contains manually configured IPv4 and IPv6 
addresses for each interface. An entry in this table
may not exist in the active state unless all objects
in the entry are consistent. In particular, the value of
hpicfIpAddressPrefixLength.

hpicfIpAddressEntry row .1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1

An entry in the hpicfIpAddressEntry contains a single
manually configured IP address.

Indexes

IF-MIBifIndex hpicfIpAddressAddrType hpicfIpAddressAddr

Column	Syntax	OID
hpicfIpAddressAddrType Type of IP address	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.1
hpicfIpAddressAddr The IP address to which this entry's addressing information pertains. hpicfIpAddressAddr is always interpreted within the context of hpicfIpAddressAddrType.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.2
hpicfIpAddressPrefixLength The prefix length associated with IP address.	INET-ADDRESS-MIBInetAddressPrefixLengthr/w Type Constraints: range: 0..2040	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.3
hpicfIpAddressType IP address type. For V4 addresses the value will be unicast.	Enumerationr/w Enumerated Values: 1 unicast 2 anycast	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.4
hpicfIpAddressRowStatus The status of the IP address entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.5
hpicfIpAddressExtendedType IP address type. For V4 addresses the value will be none. For V6 address it can be eui64 and linkLocal also.	Enumerationr/w Enumerated Values: 0 none 1 eui64 2 linkLocal	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.6

This read only table contains IPV4 and/or IPV6 addresses
for each interface.
          
These IP Addresses are either manually configured or 
obtained by a dynamic method (such as DHCP).
          
This table will hold all manually configured IP Addresses
that exist in hpicfIpAddressTable except for those entries
that are not in active state (hpicfIpAddressRowStatus).

hpicfSwitchIpAddressEntry row .1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1

An entry in the hpicfSwitchIpAddressEntry contains a single
IP address.

Indexes

IF-MIBifIndex hpicfSwitchIpAddressAddrType hpicfSwitchIpAddressAddr

Column	Syntax	OID
hpicfSwitchIpAddressAddrType Type of IP address.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.1
hpicfSwitchIpAddressAddr The IP address to which this entry's addressing information pertains. hpicfSwitchIpAddressAddr is always interpreted within the context of hpicfSwitchIpAddressAddrType.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.2
hpicfSwitchIpAddressPrefixLength The prefix length associated with IP address.	INET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.3
hpicfSwitchIpAddressType IP address type. For V4 addresses the value will be unicast.	Enumeration Enumerated Values: 1 unicast 2 anycast	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.4
hpicfSwitchIpAddressOrigin The origin of the address.	IP-MIBIpAddressOriginTC Type Values: 1 other 2 manual 4 dhcp 5 linklayer 6 random	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.5
hpicfSwitchIpAddressStatus The status of the address, describing if the address can be used for communication. In the absence of other information, an IPv4 address is always preferred(1).	IP-MIBIpAddressStatusTC Type Values: 1 preferred 2 deprecated 3 invalid 4 inaccessible 5 unknown 6 tentative 7 duplicate 8 optimistic	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.6
hpicfSwitchIpAddressPreferredLifetime The remaining length of time in seconds that this address will continue to be preferred, i.e. time until deprecation. A value of 4,294,967,295 represents infinity. The address generated from a deprecated address should …	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.7
hpicfSwitchIpAddressValidLifetime The remaining length of time, in seconds, that this address will continue to be valid, i.e. time until invalidation. A value of 4,294,967,295 represents infinity. The address generated from an invalidated address shoul…	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.8
hpicfSwitchIpAddressExtendedType IP address type. For V4 addresses the value will be none. For V6 address it can be eui64 and linkLocal also.	Enumeration Enumerated Values: 0 none 1 eui64 2 linkLocal	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.9

This table augments ipNeTtoPhysicalTable

hpicfIpNetToPhysicalEntry row .1.3.6.1.4.1.11.2.14.11.1.10.1.1.3.1

This table augments ipNeTtoPhysicalTable

Indexes

No indexes recorded

Column	Syntax	OID
hpicfIpNetToPhysicalPort This object gives the port through which the physical address was learnt	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.14.11.1.10.1.1.3.1.1

This table contains per-interface IPV4 configuration
information.

hpicfIpv4InterfaceEntry row .1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1

An entry in the hpicfIpv4InterfaceEntry contains IPV4
interface specific configuration information. This table
is indexed by ipv4InterfaceIfIndex.

Indexes

No indexes recorded

Column	Syntax	OID
hpicfIpv4InterfaceDhcpEnable Changing this flag to 'full' will clear any existing IP address configuration for this interface and will cause the device to use a dynamic method (e.g. DHCP) to obtain its IP configuration and other configuration param…	Enumerationr/w Enumerated Values: 1 full 2 off 3 inform	.1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.1
hpicfIpv4InterfaceForwarding This flag indicates whether this interface is forwarding the datagrams that were not addressed to this interface. Setting this flag to 'enabled' (the default) results in forwarding the datagrams that wer…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.2
hpicfIpv4InterfaceProxyArp Enables/disables ARP proxy on the interface. If set to 'enabled', the switch will respond on ARP request for IP addresses from other subnets. If set to disabled (the default), the switch will not respond on ARP request …	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.3
hpicfIpv4InterfaceLocalProxyArp Enables/disables local ARP proxy on the interface. If set to 'enabled', the switch will respond on ARP request for IP addresses within the local subnet. If set to disabled (the default), the switch will not respond on A…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.4
hpicfIpv4InterfaceBootpGateway This entry will specify the IP address to be used as the BOOTP gateway for this interface. Note that this IP address will be used as the BOOTP gateway only when it is configured as an IP address on this interface. Ot…	INET-ADDRESS-MIBInetAddressIPv4r/w Type Constraints: range: 4	.1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.5
hpicfIpv4InterfaceDirectedBcastFwd Enable/disable directed-broadcast forwarding on this interface. When set to default, the global hpicfDBroadcastFwdEnable setting is used. When set to enable, directed-broadcasts are enabled irrespective of the global…	Enumerationr/w Enumerated Values: 1 enabled 2 default	.1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.6

This table contains per interface IPV4
Udp encapsulated tunnel specific configuration
information.

hpicfUdpTunnelEntry row .1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1

An entry in the hpicfUdpTunnelEntry contains
Udp encapsulated tunnel specific configuration
information.

Indexes

No indexes recorded

Column	Syntax	OID
hpicfUdpTunnelSrcPort This variable is valid only for the remote mirroring source or destination switch. The value will be ignored otherwise. A value of 0 means that the UDP port is irrelevant for the tunnel type. If this value is non-zer…	INET-ADDRESS-MIBInetPortNumberr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1.1
hpicfUdpTunnelMirrorSessionID This variable is valid only for a remote mirroring switch which interfaces with the source end of the tunnel. The value will be ignored otherwise. A value of 0 means that the mirror session ID is irrelevant for the t…	Integer32r/w Constraints: range: 0-512	.1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1.2
hpicfUdpTunnelMirrorTruncate Enables/disables truncation for remote mirroring.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1.3

This table contains per-interface IPV6 configuration
information.

hpicfIpv6InterfaceEntry row .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1

An entry in the hpicfIpv6InterfaceEntry contains IPV6
interface specific configuration information. This table
is indexed by ipv6InterfaceIfIndex.

Indexes

No indexes recorded

Column	Syntax	OID
hpicfIpv6InterfaceDhcpMode Setting this flag to 'dhcpFull' will clear any existing IP address configuration for this interface and will cause the device to use a dynamic method (e.g. DHCP) to obtain its IP configuration and other configuration pa…	Enumerationr/w Enumerated Values: 0 disabled 1 dhcpFull 2 dhcpInform	.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.1
hpicfIpv6InterfaceManual Setting this flag to 'enabled' will allow manual IP address configuration but disallow any DHCP configuration.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.2
hpicfIpv6InterfaceAutoConfig Setting this flag to 'enabled' will allow host to configure automatically from default router. There may be multiple routers and in that scenario switch will add the addresses from all these routers	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.3
hpicfIpv6InterfaceDhcpRapidCommit Setting this flag to 'enabled' will allow the host to get address and configuration information from the dhcp server rapidly. This flag can be enabled only if the hpicfIpv6InterfaceDhcpMode object is set as dhcpFull. B…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.4
hpicfIpv6InterfaceDhcpRelay This flag indicates whether this interface is dhcp-relay enabled. By default this flag is set to disabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.5
hpicfIpv6InterfaceCfgEnableStatus The indication of whether IPv6 is enabled (up) or disabled (down) on this interface. Setting this object to up(1) will enable ipv6 for the given interface.Setting this object to down(2) will disable the ipv6 for the i…	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.6
hpicfIpv6InterfaceDadAttempts This object indicates the maximum number of neighbor solicitation requests that will be sent while performing duplicate address detection for this interface. Note: hpicfIpv6NDDadAttempts object's value will be in use …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.7
hpicfIpv6InterfaceDadAttemptsMode This object indicates whether the value in hpicfIpv6NDDadAttempts is in use or the value in hpicfIpv6InterfaceDadAttempts is in use for an entry in this table while performing duplicate address detection. A set to 'glo…	Enumerationr/w Enumerated Values: 1 global 2 perInterface	.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.8
hpicfIpv6InterfaceReachableTime The time a neighbor is considered reachable after receiving a reachability confirmation.	millisecondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.9
hpicfIpv6InterfaceRetransmitTime The time between retransmissions of Neighbor Solicitation messages to a neighbor when resolving the address or when probing the reachability of a neighbor.	millisecondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.10