hpicfIpv6InterfaceDadAttemptsMode
HP-ICF-IPCONFIG ·
.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.8
Object
column
r/w
Enumeration
This object indicates whether the value in hpicfIpv6NDDadAttempts is in use or the value in hpicfIpv6InterfaceDadAttempts is in use for an entry in this table while performing duplicate address detection. A set to 'global' means: - hpicfIpv6NDDadAttempts value will be used for dad attempts. A set to 'perInterface' means: - hpicfIpv6InterfaceDadAttempts value will be used for dad attempts.
Context
- MIB
- HP-ICF-IPCONFIG
- OID
.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- hpicfIpv6InterfaceEntry
- Table
- hpicfIpv6InterfaceTable
- Siblings
- 9
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | global |
2 | perInterface |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hpicfIpv6InterfaceDhcpMode Setting this flag to 'dhcpFull' will clear any existing
IP address configuration for this interface and
will cause the device to use a dynamic method
(e.g. DHCP) to obtain its IP … | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.1 |
| hpicfIpv6InterfaceRetransmitTime The time between retransmissions of Neighbor Solicitation
messages to a neighbor when resolving the address or when
probing the reachability of a neighbor. | column | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.10 |
| hpicfIpv6InterfaceManual Setting this flag to 'enabled' will allow manual IP
address configuration but disallow any DHCP configuration. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.2 |
| hpicfIpv6InterfaceAutoConfig Setting this flag to 'enabled' will allow host to
configure automatically from default router.
There may be multiple routers and in that scenario switch will
add the addresses fro… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.3 |
| hpicfIpv6InterfaceDhcpRapidCommit Setting this flag to 'enabled' will allow the host to get
address and configuration information from the dhcp server
rapidly. This flag can be enabled only if the
hpicfIpv6Interf… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.4 |
| hpicfIpv6InterfaceDhcpRelay This flag indicates whether this interface is dhcp-relay
enabled. By default this flag is set to disabled. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.5 |
| hpicfIpv6InterfaceCfgEnableStatus The indication of whether IPv6 is enabled (up) or disabled
(down) on this interface.
Setting this object to up(1) will enable ipv6 for the given
interface.Setting this object to… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.6 |
| hpicfIpv6InterfaceDadAttempts This object indicates the maximum number
of neighbor solicitation requests that will be sent
while performing duplicate address detection for
this interface.
Note: hpicfIpv6NDDad… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.7 |
| hpicfIpv6InterfaceReachableTime The time a neighbor is considered reachable after
receiving a reachability confirmation. | column | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.9 |