hpicfIpv6InterfaceRetransmitTime
HP-ICF-IPCONFIG ·
.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.10
Object
The time between retransmissions of Neighbor Solicitation messages to a neighbor when resolving the address or when probing the reachability of a neighbor.
Context
- MIB
- HP-ICF-IPCONFIG
- OID
.1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.10- Type
- column
- Access
- readwrite
- Status
- current
- Units
- milliseconds
- Parent
- hpicfIpv6InterfaceEntry
- Table
- hpicfIpv6InterfaceTable
- Siblings
- 9
Syntax
milliseconds SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hpicfIpv6InterfaceDhcpMode Setting this flag to 'dhcpFull' will clear any existing
IP address configuration for this interface and
will cause the device to use a dynamic method
(e.g. DHCP) to obtain its IP … | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.1 |
| hpicfIpv6InterfaceManual Setting this flag to 'enabled' will allow manual IP
address configuration but disallow any DHCP configuration. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.2 |
| hpicfIpv6InterfaceAutoConfig Setting this flag to 'enabled' will allow host to
configure automatically from default router.
There may be multiple routers and in that scenario switch will
add the addresses fro… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.3 |
| hpicfIpv6InterfaceDhcpRapidCommit Setting this flag to 'enabled' will allow the host to get
address and configuration information from the dhcp server
rapidly. This flag can be enabled only if the
hpicfIpv6Interf… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.4 |
| hpicfIpv6InterfaceDhcpRelay This flag indicates whether this interface is dhcp-relay
enabled. By default this flag is set to disabled. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.5 |
| hpicfIpv6InterfaceCfgEnableStatus The indication of whether IPv6 is enabled (up) or disabled
(down) on this interface.
Setting this object to up(1) will enable ipv6 for the given
interface.Setting this object to… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.6 |
| hpicfIpv6InterfaceDadAttempts This object indicates the maximum number
of neighbor solicitation requests that will be sent
while performing duplicate address detection for
this interface.
Note: hpicfIpv6NDDad… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.7 |
| hpicfIpv6InterfaceDadAttemptsMode This object indicates whether the
value in hpicfIpv6NDDadAttempts is in use or
the value in hpicfIpv6InterfaceDadAttempts
is in use for an entry in this table while
performing du… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.8 |
| hpicfIpv6InterfaceReachableTime The time a neighbor is considered reachable after
receiving a reachability confirmation. | column | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.9 |