FS-INTERFACE-MIB Table View

fsIfFlowControlAdminStatus

Type Constraints:
range: 1..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.1

fsIfPortType

Port type of this port, list as above.
port100MBASEFX indicates that port is port100MBASEFXL or port100MBASEFXS,
and system doesn't distinguish.
port1000MBASEFX indicates that port is port1000MBASEFLX or port1000MBASEFS…

Enumeration

Enumerated Values:

1	unknown
2	port10M100MBASETX
3	port100MBASEFXL
4	port100MBASEFXS
5	port1000MBASESX
6	port1000MBASELX
7	port1000MBASETX
8	portGBIC
9	port100MBASEFX
10	port1000MBASEFX
11	portSFP
12	port10GBASESR
13	port10GBASELR
14	port10GBASEER
15	port10GBASELX4
16	port10GBASESW
17	port10GBASELW
18	port10GBASEEW
19	port10GBASE
20	port40GBASEKR
21	port40GBASECR
22	port40GBASELR
23	port40GBASESR
24	port40GBASE
25	port100GBASECR
26	port100GBASESR
27	port100GBASELR
28	port100GBASEER
29	port100GBASE
50	port155MCPOS
51	port622MCPOS
52	port2G5CPOS
53	port10GCPOS
54	port155MPOS
55	port622MPOS
56	port2G5POS
57	port10GPOS
58	port155MATM
59	port622MATM
60	port2G5ATM
61	port10GATM
62	portE1ELC
63	port20GBASE
64	port25GBASE
65	port2500MBASE
66	port5000MBASE

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.2

Flow control of a port management status.

This attribute apply physical port and aggreate port

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
3	autonego
4	unknown

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.3

fsIfFlowControlOperStatus

Oper status: after the negotiation between two ports connetted
the flow contrl status.

This attribute apply physical port and aggreate port

P-BRIDGE-MIBEnabledStatus

Type Values:

1	enabled
2	disabled

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.4

fsIfAdminSpeed

port speed settings.

This attribute apply physical port and aggreate port

Enumerationr/w

Enumerated Values:

1	speed10Mb
2	speed100Mb
3	speed1000Mb
4	autonego
5	speed10Gb
6	unknown
7	speed40Gb
8	speed100Gb

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.5

fsIfAdminDuplex

port duplex settings.

This attribute apply physical port and aggreate port

Enumerationr/w

Enumerated Values:

1	full
2	half
3	autonego
4	unknown

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.6

fsIfOperSpeed

After two port have negotiated the speed status,and this object
is the working speed status. while the port link status is down ,
then the speed status is unknown(4).

This attribute apply physical port a…

Enumeration

Enumerated Values:

1	speed10Mb
2	speed100Mb
3	speed1000Mb
4	unknown
5	speed10Gb
6	speed40Gb
7	speed100Gb

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.7

fsIfOperDuplex

After two port have negotiated the duplex status, and this object
is the working duplex status. while the port link status is down ,
then the speed status is unknown(3).

This attribute apply physical por…

Enumeration

Enumerated Values:

1	full
2	half
3	unknown

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.8

fsIfManageStatus

Management status of the interface.

P-BRIDGE-MIBEnabledStatusr/w

Type Values:

1	enabled
2	disabled

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.9

fsIfIpBroadcast

Broadcast address of the interface. if broadcast address not configured on interface, return 0.0.0.0

SNMPv2-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.10

fsIfLayer

Enumerationr/w

Enumerated Values:

1	layer-2
2	layer-3

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.11

fsIfMode

This value is meaning for only physical port and aggreate port

Enumerationr/w

Enumerated Values:

1	access
2	trunk
3	dot1q-tunnel
4	hybrid
5	other
6	uplink
7	host
8	promiscuous

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.12

fsIfCounterClear

Setting its to any value but 0, will clear counters of this interface.
Setting its value to 0 will cause no action of the agent. and when
query will always return 0.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.13

fsIfEntryStatus

Status of this entry, set this object to valid will create a interface,
and set its value to invalid will delete the interface of this entry.

FS-TCConfigStatusr/w

Type Values:

1	valid
2	invalid

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.14

fsIfMediumType

Port medium type of this port,fiber or copper.

Enumerationr/w

Enumerated Values:

0	unknown
1	copper
2	fiber

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.15

fsIfDownCounter

The counters of linkdown times of the interface.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.16

fsIfInOctets

The total number of octets received on the interface,
including framing characters.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated b…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.17

fsIfOutOctets

The total number of octets transmitted out of the
interface, including framing characters.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indi…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.18

fsIfBcastInhibit

The percentage of the broadcast storm restraint on the
interface.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.19

fsIfNegotiation

The negotiation status of the interface.

Enumerationr/w

Enumerated Values:

0	disable
1	enable

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.20

fsIfPhysAddress

The interface's address at its protocol sub-layer. For
example, for an 802.x interface, this object normally
contains a MAC address. The interface's media-specific MIB
must define the bit and byte ordering and the for…

SNMPv2-TCMacAddress

Type Constraints:
range: 6

Description:

Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.21

fsIfAdminSpeedRW

port speed settings.

This attribute apply physical port and aggreate port

Enumerationr/w

Enumerated Values:

1	speed10Mb
2	speed100Mb
3	speed1000Mb
4	autonego
5	speed10Gb
6	unknown
7	speed40Gb
8	speed100Gb

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.22

fsIfAdminDuplexRW

port duplex settings.

This attribute apply physical port and aggreate port

Enumerationr/w

Enumerated Values:

1	full
2	half
3	autonego
4	unknown

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.23

fsIfModeRW

This value is meaning for only physical port and aggreate port

Enumerationr/w

Enumerated Values:

1	access
2	trunk
3	dot1q-tunnel
4	hybrid
5	other
6	uplink
7	host
8	promiscuous

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.24

fsIfSpeed

An estimate of the interface's current bandwidth in units of
Mbits per second.

RFC1155-SMIGauge

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.25

fsifAdminStatus

the interface keeps the admin state .

Enumerationr/w

Enumerated Values:

1	adminup
2	admindown
3	admintest

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.26

fsifOperStatus

the interface keeps the oper state .

Enumeration

Enumerated Values:

1	up
2	down
3	test
4	unknow
5	dormant

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.27

fsIfInNUcastPkts

The counter of receiving packets contain BROADCAST and PACKET_MULTICAST .

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.28

fsIfOutNUcastPkts

The counter of sending packets contain BROADCAST and PACKET_MULTICAST .

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.29

fsIfUpDownTimes

The counters of linkup and linkdown times of the interface.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.30

fsifAdminStatusw

The desired state of the interface. When a managed system initializes, all
interfaces start with ifAdminStatus in the admindown(1)
state. As a result of either explicit management
action or per configuration informati…

Enumerationr/w

Enumerated Values:

0	up
1	admindown

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.31

fsifOperStatusw

The current operational state of the interface.
If fsApIfAdminStatus is admindown(2) then
fsApIfOperStatus should be admindown(2). If fsApIfAdminStatus is
changed to up(0) then fsApIfOperStatus should change to
up(0)…

Enumeration

Enumerated Values:

0	up
1	down
2	admindown

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.32

fsifSpeedw

An estimate of the interface's current bandwidth in units of
Mbits per second.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.33

fsifMacAddress

The interface's address at its protocol sub-layer.
For example, for an 802.x interface, this object
normally contains a MAC address. The interface's
media-specific MIB must define the bit and byte
ordering and the form…

SNMPv2-TCMacAddress

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.34

fsifLastChange

The length of the time that comes current state .

SNMPv2-SMITimeTicks

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.35

fsIfInPkts

The number of packets received on this interface,
including framing characters.

Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as …

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.36

fsIfDiscard

The number of bound packets which were chosen to be
discarded even though no errors. One possible reason for
discarding such a packet could be to free up buffer space.

Discontinuities in the value of this…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.37

fsIfBandwidthUsage

Current bandwidth utilization of interface.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.38

fsIfInBitsRate

The average input packet-rate over a period of time(configuration by interface command 'load-interval')
in bits per second on this interface.

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.39

fsIfInPktRate

The average input packet-rate over a period of time(configuration by interface command 'load-interval')
in packets per second on this interface.

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.40

fsIfOutBitsRate

The average output packet-rate over a period of time(configuration by interface command 'load-interval')
in bits per second on this interface.

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.41

fsIfOutPktRate

The average output packet-rate over a period of time(configuration by interface command 'load-interval')
in packets per second on this interface.

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.42

fsIfInBandwidthUsage

RX bandwidth utilization ratio of interface.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.43

fsIfOutBandwidthUsage

TX bandwidth utilization ratio of interface.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.44

fsIfInErrorPktsRate

Input packet error rate.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.45

fsIfOutErrorPktsRate

Output packet error rate.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.46

fsIfInDropPktsRate

Input packet discarded rate.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.47

fsIfOutDropPktsRate

Output packet discarded rate.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.48

fsIfOutNoBuffer

Ouyput drop packet rate on this interface due to resource lack.

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.49

fsIfOutPkts

The number of packets sent on this interface,
including framing characters.

Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indi…

fsIfIpIfIndex fsIfIpId fsIfIp

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.1.1.50

fsIfIpTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.2 · 1 row entry · 5 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfIpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfIpTable'

A list of interface ip configuration entries.

fsIfIpEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1

An entry containing configuration information applicable
to a Layer3 interface.

Indexes

Column Syntax OID

fsIfIpIfIndex

A unique value, for each Layer3 interface.

Type Constraints:
range: 1..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1.1

fsIfIpId

Type of interface ip address.

Enumeration

Enumerated Values:

1	primary
2	secondary

.1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1.2

fsIfIp

Ip address of the interface fsIfIndex refer to.

SNMPv2-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1.3

fsIfIpMask

Ip mask of the interface ip address.

SNMPv2-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1.4

fsIfIpEntryStatus

entry status of this entry. and the means in this enviraments can
reffer to the text-convention definition of the RowStatus.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …

.1.3.6.1.4.1.52642.1.1.10.2.10.1.2.1.5

fsIfStatusTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.3 · 1 row entry · 4 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfStatusTable'

list of interface status. Status information include some error state and
result of examining to the interface,etc.

fsIfStatusEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.3.1

Entry contains interface status information.

Indexes

fsIfStatusIndex

Column Syntax OID

fsIfStatusIndex

fsIfStatusLoopBackExamine

Type Constraints:
range: 1..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.3.1.1

Setting its to any value but 0, will Checking whether this port or aggreate can
receive and send packets normally, It indicates that port or aggreate is normal
if opertion is success.
Setting its value to 0 will ca…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.3.1.2

fsIfErrorStatus

Port's error status information

Enumeration

Enumerated Values:

1	no-error
2	err-disable-bpduguard
3	err-disable-ptsecurity

.1.3.6.1.4.1.52642.1.1.10.2.10.1.3.1.3

fsIfLineDetect

When reading this object, system detects the quality of line connecting the port.
Detect whether the line is broken or short circuit or not.

The meaning of the obtained value:
Return value=N*10000000+M
N…

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.3.1.4

fsPortTypeChooseTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.5 · 1 row entry · 2 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsPortTypeChooseTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsPortTypeChooseTable'

Table of entrance to choose port type.

fsPortTypeChooseEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.5.1

Entrance to choose port type.

Indexes

fsPortTypeChooseIndex

Column Syntax OID

fsPortTypeChooseIndex

The logic port number.

fsApPhysAddress fsApIfIndex

Type Constraints:
range: 1..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.5.1.1

fsPortTypeChooseType

The chosen port type. This object is used to choose one of the multiple physical ports of different types,
when the same logical port is correspondent with them.
Apply this attribute to the physical port only.

Enumeration

Enumerated Values:

1	fiber
2	copper

.1.3.6.1.4.1.52642.1.1.10.2.10.1.5.1.2

fsIfMTUTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.6 · 1 row entry · 2 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfMTUTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfMTUTable'

Access table of MTU on interface.

fsIfMTUEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.6.1

Interfac MTU access.

Indexes

fsIfMTUIndex

Column	Syntax	OID
fsIfMTUIndex Interface number	FS-TCIfIndex Type Constraints: `range: 1..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.6.1.1`
fsIfMTU Interface MTU.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.6.1.2`

fsIfAvailableBWTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.7 · 1 row entry · 2 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfAvailableBWTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfAvailableBWTable'

Access table of Available Bandwidth on interface.

fsIfAvailableBWEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.7.1

Interfac available bandwidth access.

Indexes

fsIfAvailableBWIfIndex

Column	Syntax	OID
fsIfAvailableBWIfIndex Interface number	FS-TCIfIndex Type Constraints: `range: 1..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.7.1.1`
fsIfAvailableBWIfBW Interface available bandwidth(bit).	RFC1155-SMIGauge Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.7.1.2`

fsIfSVICreatTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.8 · 1 row entry · 2 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfSVICreatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfSVICreatTable'

Access table of Available Bandwidth on interface.

fsIfSVICreatEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.8.1

Interfac available bandwidth access.

Indexes

fsIfSVICreatVlanNum

Column Syntax OID

fsIfSVICreatVlanNum

Interface Vlan number

Integer32

Constraints:
range: 1-4094

.1.3.6.1.4.1.52642.1.1.10.2.10.1.8.1.1

fsIfHandleSVI

0 creat,1 delete.

Enumerationr/w

Enumerated Values:

0	create
1	delete

.1.3.6.1.4.1.52642.1.1.10.2.10.1.8.1.2

fsIfLinkUPTimesTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.10 · 1 row entry · 2 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfLinkUPTimesTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfLinkUPTimesTable'

Access table of Available Bandwidth on interface.

fsIfLinkUPTimesEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.10.1

Interfac available bandwidth access.

Indexes

fsInterfaceIndex

Column	Syntax	OID
fsInterfaceIndex Interface Index	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.10.1.1`
fsIfLinkUPTimes Vlaues Of Linkup Times.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.10.1.2`

fsIfEncapsulationTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.11 · 1 row entry · 2 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfEncapsulationTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfEncapsulationTable'

Access table of Encapsulation dot1q VLAN on interface.

fsIfEncapsulationEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.11.1

Interfac encapsulation dot1q VLAN access.

Indexes

fsIfEncapsulationIndex

Column	Syntax	OID
fsIfEncapsulationIndex A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system …	FS-TCIfIndex Type Constraints: `range: 1..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.11.1.1`
fsIfEncapsulationVlan The value indicate the VID of the dot1q vlan encapsulation. The value 0 means de-encapsulation.	Q-BRIDGE-MIBVlanIdr/w Type Constraints: `range: 1..4094`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.11.1.2`

fsApIfNumberTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.12 · 1 row entry · 3 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsApIfNumberTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsApIfNumberTable'

Access table of ap interface number.

fsApIfNumberEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.12.1

Interfac number of ap.

Indexes

fsApPhyAddress

Column	Syntax	OID
fsApPhyAddress The ap's address at its protocol sub-layer. The ap's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial …	SNMPv2-TCPhysAddress Description: Represents media- or physical-level addresses.	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.12.1.1`
fsApIfNumber Vlaues Of interface number.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.12.1.2`
fsApIfPhyIntNum Vlaues Of physical interface number.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.12.1.3`

fsApIfTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13 · 1 row entry · 49 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsApIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsApIfTable'

A list of fsAp interface entries.  The number of entries
is given by the value of fsApIfNumber.

fsApIfEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1

An entry containing management information fsApplicable
to a particular interface.

Indexes

Column Syntax OID

fsApPhysAddress

The ap's address at its protocol sub-layer.
The ap's media-specific MIB must define the bit and byte
ordering and the format of the value of this object.
For interfaces which do not have such an address
(e.g., a serial …

SNMPv2-TCPhysAddress

Description:

Represents media- or physical-level addresses.

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.1

fsApIfIndex

A unique value, greater than zero, for each
interface. It is recommended that values are assigned
contiguously starting from 1. The value for each
interface sub-layer must remain constant at least from
one re-initiali…

Type Constraints:
range: 1..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.2

fsApIfDescr

A textual string containing information about the
interface. This string should include the name of the
manufacturer, the product name and the version of the
interface hardware/software.

OctetString

Constraints:
range: 0-255

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.3

fsApIfType

The type of interface. Additional values for ifType
are assigned by the Internet Assigned Numbers
Authority (IANA), through updating the syntax of the
IANAifType textual convention.

IANAifType-MIBIANAifType

Type Values:

1	other
2	regular1822
3	hdh1822
4	ddnX25
5	rfc877x25
6	ethernetCsmacd
7	iso88023Csmacd
8	iso88024TokenBus
9	iso88025TokenRing
10	iso88026Man
11	starLan
12	proteon10Mbit
13	proteon80Mbit
14	hyperchannel
15	fddi
16	lapb
17	sdlc
18	ds1
19	e1
20	basicISDN
21	primaryISDN
22	propPointToPointSerial
23	ppp
24	softwareLoopback
25	eon
26	ethernet3Mbit
27	nsip
28	slip
29	ultra
30	ds3
31	sip
32	frameRelay
33	rs232
34	para
35	arcnet
36	arcnetPlus
37	atm
38	miox25
39	sonet
40	x25ple
41	iso88022llc
42	localTalk
43	smdsDxi
44	frameRelayService
45	v35
46	hssi
47	hippi
48	modem
49	aal5
50	sonetPath
51	sonetVT
52	smdsIcip
53	propVirtual
54	propMultiplexor
55	ieee80212
56	fibreChannel
57	hippiInterface
58	frameRelayInterconnect
59	aflane8023
60	aflane8025
61	cctEmul
62	fastEther
63	isdn
64	v11
65	v36
66	g703at64k
67	g703at2mb
68	qllc
69	fastEtherFX
70	channel
71	ieee80211
72	ibm370parChan
73	escon
74	dlsw
75	isdns
76	isdnu
77	lapd
78	ipSwitch
79	rsrb
80	atmLogical
81	ds0
82	ds0Bundle
83	bsc
84	async
85	cnr
86	iso88025Dtr
87	eplrs
88	arap
89	propCnls
90	hostPad
91	termPad
92	frameRelayMPI
93	x213
94	adsl
95	radsl
96	sdsl
97	vdsl
98	iso88025CRFPInt
99	myrinet
100	voiceEM
101	voiceFXO
102	voiceFXS
103	voiceEncap
104	voiceOverIp
105	atmDxi
106	atmFuni
107	atmIma
108	pppMultilinkBundle
109	ipOverCdlc
110	ipOverClaw
111	stackToStack
112	virtualIpAddress
113	mpc
114	ipOverAtm
115	iso88025Fiber
116	tdlc
117	gigabitEthernet
118	hdlc
119	lapf
120	v37
121	x25mlp
122	x25huntGroup
123	transpHdlc
124	interleave
125	fast
126	ip
127	docsCableMaclayer
128	docsCableDownstream
129	docsCableUpstream
130	a12MppSwitch
131	tunnel
132	coffee
133	ces
134	atmSubInterface
135	l2vlan
136	l3ipvlan
137	l3ipxvlan
138	digitalPowerline
139	mediaMailOverIp
140	dtm
141	dcn
142	ipForward
143	msdsl
144	ieee1394
145	if-gsn
146	dvbRccMacLayer
147	dvbRccDownstream
148	dvbRccUpstream
149	atmVirtual
150	mplsTunnel
151	srp
152	voiceOverAtm
153	voiceOverFrameRelay
154	idsl
155	compositeLink
156	ss7SigLink
157	propWirelessP2P
158	frForward
159	rfc1483
160	usb
161	ieee8023adLag
162	bgppolicyaccounting
163	frf16MfrBundle
164	h323Gatekeeper
165	h323Proxy
166	mpls
167	mfSigLink
168	hdsl2
169	shdsl
170	ds1FDL
171	pos
172	dvbAsiIn
173	dvbAsiOut
174	plc
175	nfas
176	tr008
177	gr303RDT
178	gr303IDT
179	isup
180	propDocsWirelessMaclayer
181	propDocsWirelessDownstream
182	propDocsWirelessUpstream
183	hiperlan2
184	propBWAp2Mp
185	sonetOverheadChannel
186	digitalWrapperOverheadChannel
187	aal2
188	radioMAC
189	atmRadio
190	imt
191	mvl
192	reachDSL
193	frDlciEndPt
194	atmVciEndPt
195	opticalChannel
196	opticalTransport
197	propAtm
198	voiceOverCable
199	infiniband
200	teLink
201	q2931
202	virtualTg
203	sipTg
204	sipSig
205	docsCableUpstreamChannel
206	econet
207	pon155
208	pon622
209	bridge
210	linegroup
211	voiceEMFGD
212	voiceFGDEANA
213	voiceDID
214	mpegTransport
215	sixToFour
216	gtp
217	pdnEtherLoop1
218	pdnEtherLoop2
219	opticalChannelGroup
220	homepna
221	gfp
222	ciscoISLvlan
223	actelisMetaLOOP
224	fcipLink
225	rpr
226	qam
227	lmp
228	cblVectaStar
229	docsCableMCmtsDownstream
230	adsl2
231	macSecControlledIF
232	macSecUncontrolledIF
233	aviciOpticalEther
234	atmbond
235	voiceFGDOS
236	mocaVersion1
237	ieee80216WMAN
238	adsl2plus
239	dvbRcsMacLayer
240	dvbTdm
241	dvbRcsTdma
242	x86Laps
243	wwanPP
244	wwanPP2
245	voiceEBS
246	ifPwType
247	ilan
248	pip
249	aluELP
250	gpon
251	vdsl2
252	capwapDot11Profile
253	capwapDot11Bss
254	capwapWtpVirtualRadio
255	bits
256	docsCableUpstreamRfPort
257	cableDownstreamRfPort
258	vmwareVirtualNic
259	ieee802154
260	otnOdu
261	otnOtu
262	ifVfiType
263	g9981
264	g9982
265	g9983
266	aluEpon
267	aluEponOnu
268	aluEponPhysicalUni
269	aluEponLogicalLink
270	aluGponOnu
271	aluGponPhysicalUni
272	vmwareNicTeam
277	docsOfdmDownstream
278	docsOfdmaUpstream
279	gfast
280	sdci
281	xboxWireless
282	fastdsl
283	docsCableScte55d1FwdOob
284	docsCableScte55d1RetOob
285	docsCableScte55d2DsOob
286	docsCableScte55d2UsOob
287	docsCableNdf
288	docsCableNdr
289	ptm
290	ghn
291	otnOtsi
292	otnOtuc
293	otnOduc
294	otnOtsig
295	microwaveCarrierTermination
296	microwaveRadioLinkTerminal
297	ieee8021axDrni
298	ax25
299	ieee19061nanocom
300	cpri
301	omni
302	roe
303	p2pOverLan

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.4

fsApIfMtu

The size of the largest packet which can be
sent/received on the interface, specified in octets.
For interfaces that are used for transmitting network
datagrams, this is the size of the largest network
datagram that can…

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.5

fsApIfSpeed

An estimate of the interface's current bandwidth in units of
Mbits per second. For interfaces which do not vary in
bandwidth or for those where no accurate estimation
can be made, this object should contain the nominal…

RFC1155-SMIGauge

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.6

fsApIfPhysAddress

The interface's address at its protocol sub-layer.
For example, for an 802.x interface, this object
normally contains a MAC address. The interface's
media-specific MIB must define the bit and byte
ordering and the form…

SNMPv2-TCPhysAddress

Description:

Represents media- or physical-level addresses.

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.7

fsApIfAdminStatus

The desired state of the interface. The testing(3)
state indicates that no operational packets can be
passed. When a managed system initializes, all
interfaces start with ifAdminStatus in the admindown(2)
state. As a…

Enumerationr/w

Enumerated Values:

1	up
2	admindown
3	testing

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.8

fsApIfOperStatus

The current operational state of the interface.
If fsApIfAdminStatus is admindown(2) then
fsApIfOperStatus should be admindown(3). If fsApIfAdminStatus is
changed to up(1) then fsApIfOperStatus should change to
up(1)…

Enumeration

Enumerated Values:

1	up
2	down
3	admindown
4	unknown
5	dormant
6	notPresent
7	lowerLayerDown

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.9

fsApIfLastChange

The value of sysUpTime at the time the interface
entered its current operational state. If the current
state was entered prior to the last re-initialization
of the local network management subsystem, then this
object c…

SNMPv2-SMITimeTicks

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.10

fsApIfInOctets

The total number of octets received on the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.11

fsApIfInUcastPkts

The number of packets, delivered by this sub-layer to
a higher (sub-)layer, which were not addressed to a
multicast or broadcast address at this sub-layer.

Discontinuities in the value of this counter can…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.12

fsApIfInNUcastPktsdeprecated

The number of packets, delivered by this sub-layer to
a higher (sub-)layer, which were addressed to a
multicast or broadcast address at this sub-layer.

Discontinuities in the value of this counter can occ…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.13

fsApIfInDiscards

The number of inbound packets which were chosen to be
discarded even though no errors had been detected to
prevent their being deliverable to a higher-layer
protocol. One possible reason for discarding such a
packet co…

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.14

fsApIfInErrors

For packet-oriented interfaces, the number of inbound
packets that contained errors preventing them from
being deliverable to a higher-layer protocol. For
character-oriented or fixed-length interfaces, the
number of in…

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.15

fsApIfInUnknownProtos

For packet-oriented interfaces, the number of packets
received via the interface which were discarded
because of an unknown or unsupported protocol. For
character-oriented or fixed-length interfaces that
support protoc…

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.16

fsApIfOutOctets

The total number of octets transmitted out of the
interface, including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
othe…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.17

fsApIfOutUcastPkts

The total number of packets that higher-level
protocols requested be transmitted, and which were not
addressed to a multicast or broadcast address at this
sub-layer, including those that were discarded or not
sent.
…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.18

fsApIfOutNUcastPktsdeprecated

The total number of packets that higher-level
protocols requested be transmitted, and which were
addressed to a multicast or broadcast address at this
sub-layer, including those that were discarded or not
sent.
…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.19

fsApIfOutDiscards

The number of outbound packets which were chosen to
be discarded even though no errors had been detected
to prevent their being transmitted. One possible
reason for discarding such a packet could be to free
up buffer s…

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.20

fsApIfOutErrors

For packet-oriented interfaces, the number of
outbound packets that could not be transmitted because
of errors. For character-oriented or fixed-length
interfaces, the number of outbound transmission units
that could no…

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.21

fsApIfOutQLendeprecated

The length of the output packet queue (in packets).

RFC1155-SMIGauge

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.22

fsApIfLinkUPTimes

Vlaues Of Linkup Times.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.23

fsApIfInDataOctets

The data octets received on the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicat…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.24

fsApIfOutDataOctets

The data octets transmitted out of the
interface, including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as …

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.25

fsApIfMgmtUploadOctets

The upload octets received on the mgmt interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as …

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.26

fsApIfMgmtDownloadOctets

The download octets transmitted out of the
mgmt interface, including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other …

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.27

fsApIfSpeedw

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.28

fsApIfMtuw

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.29

fsApIfPhysAddressw

The interface's address at its protocol sub-layer.
For example, for an 802.x interface, this object
normally contains a MAC address. The interface's
media-specific MIB must define the bit and byte
ordering and the form…

SNMPv2-TCMacAddress

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.30

fsApIfInUcastPktsw

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.31

fsApIfInNUcastPktswdeprecated

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.32

fsApIfOutUcastPktsw

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.33

fsApIfOutNUcastPktswdeprecated

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.34

fsApIfLinkUPTimesw

The counters of linkup and linkdown times of the interface.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.35

fsApIfInPkts

The total number of packets received on the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other time…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.36

fsApIfInFlow

The flow rate of data octets in units of Bytes per-second received on the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the manage…

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.37

fsApIfOutFlow

The flow rate of data octets in units of Bytes per-second transmitted out of the
interface, including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the…

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.38

fsApIfInBrdcastPkts

The total number of broadcast packets received on the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.39

fsApIfOutBrdcastPkts

The total number of broadcast packets transmitted out of the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, …

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.40

fsApIfInMulcastPkts

The total number of multicast packets received on the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.41

fsApIfOutMulcastPkts

The total number of multicast packets transmitted out of the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, …

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.42

fsApIfInPayloadOctets

The total number of payload octets received on the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
oth…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.43

fsApIfOutPayloadOctets

The total number of payload octets transmitted out of the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.44

fsApIfAlias

A textual string containing alias information about the
interface.

OctetString

Constraints:
range: 0-255

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.45

fsApIfInDateRate

The flow rate of data octets in units of Kilo-Bits per-second received on the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the ma…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.46

fsApIfOutDateRate

The flow rate of data octets in units of Kilo-Bits per-second transmitted out of the
interface, including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.47

fsApifInNormalPkts

The total number of normal packets received on the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
oth…

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.48

fsApIfOutPkts

The total number of packets transmitted out of the interface,
including framing characters.

Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
oth…

fsLinkQosCtlOwnerIndex fsLinkQosCtlTestName

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.52642.1.1.10.2.10.1.13.1.49

fsIfLinkTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.14 · 1 row entry · 25 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfLinkTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfLinkTable'

A list of interface entries.  The number of entries is
given by the value of ifNumber.

fsIfLinkEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1

An entry containing management information applicable to a
particular interface.

Indexes

fsIfLinkIndex

Column	Syntax	OID
fsIfLinkIndex A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initiali…	FS-TCIfIndex Type Constraints: `range: 1..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.1`
fsIfUplinkInOctets The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.2`
fsIfUplinkInUcastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.3`
fsIfUplinkInNUcastPktsdeprecated The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occ…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.4`
fsIfUplinkInDiscards The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.5`
fsIfUplinkInErrors For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character- oriented or fixed-length interfaces, the number of i…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.6`
fsIfUplinkOutOctets The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at othe…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.7`
fsIfUplinkOutUcastPkts The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.8`
fsIfUplinkOutNUcastPktsdeprecated The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.9`
fsIfUplinkOutDiscards The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer s…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.10`
fsIfUplinkOutErrors For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.11`
fsIfDownlinkInOctets The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.12`
fsIfDownlinkInUcastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.13`
fsIfDownlinkInNUcastPktsdeprecated The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occ…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.14`
fsIfDownlinkInDiscards The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.15`
fsIfDownlinkInErrors For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character- oriented or fixed-length interfaces, the number of i…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.16`
fsIfDownlinkOutOctets The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at othe…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.17`
fsIfDownlinkOutUcastPkts The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.18`
fsIfDownlinkOutNUcastPktsdeprecated The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.19`
fsIfDownlinkOutDiscards The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer s…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.20`
fsIfDownlinkOutErrors For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not…	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.21`
fsIfUplinkInBcastPkts The number of upbound and inbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counte…	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.22`
fsIfUplinkOutBcastPkts The number of upbound and outbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this count…	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.23`
fsIfDownlinkInBcastPkts The number of downbound and inbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this coun…	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.24`
fsIfDownlinkOutBcastPkts The number of downbound and outbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this cou…	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.14.1.25`

fsIfLinkTrafficTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1 · 1 row entry · 5 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfLinkTrafficTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfLinkTrafficTable'

A table of link traffic statistics, including interface rate and bandwidth utilization.

fsIfLinkTrafficEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1

The link traffic statistics entry.

Indexes

fsIfLinkTrafficIndex

Column	Syntax	OID
fsIfLinkTrafficIndex The link traffic interface index.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1.1`
fsIfLinkAvgRate An estimate of the interface's average bandwidth in units of bits per second.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1.2`
fsIfLinkPeakRate An estimate of the interface's current peak bandwidth in units of bits per second.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1.3`
fsIfLinkAvgBWUtilization An estimate of the interface's average bandwidth Utilization.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1.4`
fsIfLinkPeakBWUtilization An estimate of the interface's current peak bandwidth Utilization.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.1.1.1.5`

fsLinkQosCtlTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1 · 1 row entry · 6 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsLinkQosCtlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsLinkQosCtlTable'

The results of these operations are stored in the fsLinkQosResultsTable

fsLinkQosCtlEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1

Defines an entry in the fsLinkQosCtlTable. The first index
element, fsLinkQosCtlOwnerIndex, is of type SnmpAdminString,
a textual convention that allows for use of the SNMPv3
View-Based Access Control Model (RFC 3415, …

Indexes

Column Syntax OID

fsLinkQosCtlOwnerIndex

To facilitate the provisioning of access control by a
security administrator using the View-Based Access
Control Model (RFC 2575, VACM) for tables in which
multiple users may need to create or
modify entries independent…

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.1

fsLinkQosCtlTestName

The name of the ping-based test. This is locally unique,
within the scope of a fsLinkQosCtlOwnerIndex.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.2

fsLinkQosCtlTargetAddressType

Specifies the type of host address to be used at a remote
host for performing a ping-based operation.

INET-ADDRESS-MIBInetAddressTyper/w

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.3

fsLinkQosCtlTargetAddress

Specifies the host address to be used at a remote host for
performing a ping-based operation. The host address type is
determined by the value of the corresponding
fsLinkQosCtlTargetAddressType.

INET-ADDRESS-MIBInetAddressr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.4

fsLinkQosCtlAdminStatus

Reflects the desired state that a fsLinkQosCtlEntry should be
in:
enabled(1) - Attempt to activate the test as defined by
this fsLinkQosCtlEntry.
disabled(2) - Deactivate the test as defined by t…

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.5

fsLinkQosCtlRowStatus

This variable is used to create, modify, and/or
delete a row in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.1.1.6

fsLinkQosResultsTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2 · 1 row entry · 9 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsLinkQosResultsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsLinkQosResultsTable'

The results of these operations are stored in the fsLinkQosResultsTable.

fsLinkQosResultsEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1

Defines an entry in the fsLinkQosResultsTable. The
fsLinkQosResultsTable has the same indexing as the
fsLinkQosCtlTable so that a fsLinkQosResultsEntry
corresponds to the fsLinkQosCtlEntry that caused it to
be created.

Indexes

fsLinkQosCtlOwnerIndex fsLinkQosCtlTestName

Column Syntax OID

fsLinkQosResultsOperStatus

Reflects the operational state of a fsLinkQosCtlEntry:
enabled(1) - Test is active.
disabled(2) - Test has stopped.
completed(3) - Test is completed.

Enumeration

Enumerated Values:

1	enabled
2	disabled
3	completed

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.1

fsLinkQosResultsIpTargetAddressType

This object indicates the type of address stored in the
corresponding fsLinkQosResultsIpTargetAddress object.

INET-ADDRESS-MIBInetAddressType

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.2

fsLinkQosResultsIpTargetAddress

This object reports the IP address associated with a
fsLinkQosCtlTargetAddress value when the destination
address is specified as a DNS name. The value of this
object should be a zero-length octet string when a DNS
…

INET-ADDRESS-MIBInetAddress

Type Constraints:
range: 0..255

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.3

fsLinkQosResultsMaxRtt

The maximum packet round-trip-time (RTT) that received. A value
of 0 for this object implies that no RTT has been received.

millisecondsSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.4

fsLinkQosResultsMinRtt

The minimum packet round-trip-time (RTT) that received. A value
of 0 for this object implies that no RTT has been received.

millisecondsSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.5

fsLinkQosResultsAverageRtt

The current average packet round-trip-time (RTT).

millisecondsSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.6

fsLinkQosResultsDelayJitter

This object contains the sum of the squares for all ping
responses received. Its purpose is to enable standard
deviation calculation. The estimate value of the delay jitter.

millisecondsSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.7

fsLinkQosResultsPktsLossRate

The packets loss rate of the link.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.8

fsLinkQosResultsNetworkAF

The network availability factor.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.2.2.1.9

fsIfDeviceTrafficTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1 · 1 row entry · 16 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfDeviceTrafficTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfDeviceTrafficTable'

A table of device traffic statistics.

fsIfDeviceTrafficEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1

Device traffic statistics entry

Indexes

fsIfDeviceTrafficIndex

Column	Syntax	OID
fsIfDeviceTrafficIndex The device traffic interface index.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.1`
fsIfFC The FC type. 2--BASE_X_10 4--BASE_X_100 6--BASE_X_1000 8--BASE_X_10000 9--BASE_ERROR	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.2`
fsIfFCTransRate The transmission rate of the FC.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.3`
fsIfFCTransPktsNum The transmission packets number of the FC.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.4`
fsIfFCDiscardRate The discard rate of the FC.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.5`
fsIfFCDiscardPktsNum The discard packets number of the FC.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.6`
fsIfFCPktsLossRate The packets loss rate of the FC.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.7`
fsIfFCBandwidthRate The bandwidth rate of the FC.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.8`
fsIfFCBandwidthPercentage The bandwidth percentage of the FC.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.9`
fsIfDeviceFCGathers Gathers of the device FC.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.10`
fsIfFullMeshFCGathers Gathers of the whole network FC.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.11`
fsIfClassBasedGathers Class-based Gathers.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.12`
fsIfNodeBasedGathers Node-based Gathers.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.13`
fsIfNodeClassBasedGathers Node&class-based Gathers.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.14`
fsIfNodeFCBasedGathers Node&FC-based Gathers.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.15`
fsIfNodeDeviceFCBasedGathers Node&device&FC-based Gathers.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.52642.1.1.10.2.10.1.15.3.1.1.16`

fsIfPhyTable

table

.1.3.6.1.4.1.52642.1.1.10.2.10.1.16 · 1 row entry · 2 columns

Open in standard view

Uses the fscom variant from /opt/observium/mibs/fscom.

Command help

Walk fsIfPhyTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'FS-INTERFACE-MIB' -M '/opt/observium/mibs/fscom:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'FS-INTERFACE-MIB::fsIfPhyTable'

list of physical interface basic configuration objects.

fsIfPhyEntry row .1.3.6.1.4.1.52642.1.1.10.2.10.1.16.1

Entry contains physical interface basic configurations.

Indexes

fsIfPhyIndex

Column Syntax OID

fsIfPhyIndex

Physical port index.