CADANT-CMTS-EQUIPMENT-MIB Table View

A table of card or circuit pack information.

cerCardEntry row .1.3.6.1.4.1.4998.1.1.10.1.4.12.1

A conceptual row containing pertinent information about a card or
a circuit pack.

Indexes

cerCardId

Column	Syntax	OID
cerCardId The unique id of this card within the shelf. The convention of cardId is as follows: - Indices from 1 to 50 [1 - 50] are reserved for Circuit Packs. In this case, the cardId is 1 plus the 0-based slot number. - Indi…	CADANT-TCCardId Type Constraints: range: 0..99	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.2
cerCardName This is the name of the card, if it has one.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.3
cerCardType The type of card, if any. For example Ecard, Fcard, Dcard or Ucard If the slot is empty, the value would be 'empty'.	CADANT-TCCerCardType Type Values: 0 invalid 1 fan 2 pem 3 ccm 4 cdm 5 sam 6 rsm 7 ucam 8 dcam 98 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.4
cerCardSubType The cardType alone may not be specific enough to fully describe the type of card that is in this slot. For example, a card type of Dcard might have a more specific type of 1D8U with integrated upconverter. If the card …	CADANT-TCCerCardSubTyper/w Type Values: 0 invalid 1 fan 2 pem 3 ccm 4 cdm 5 sam 6 rsm10g 7 ucam96m24c 8 dcam192m8cAnnexA 9 dcam256m8cAnnexB 98 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.5
cerCardAdminState This is the administrative state of this card.	CADANT-TCAdminStater/w Type Values: 1 up 2 down	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.12
cerCardPrState This is the primary state of this card.	CADANT-TCPrimaryState Type Values: 1 is 2 oos	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.13
cerCardSecState This is the secondary state of this card.	CADANT-TCSecondaryState Type Values: 0 notapplicable 1 manual 2 fault 3 diagnostic 4 overload 5 normal 6 degrade 7 initializing 8 swdownload 9 firmwarepump 10 powerup 11 bootdkm	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.14
cerCardDplxStatus This is the duplexing status of this card.	CADANT-TCDuplexStatus Type Values: 0 notapplicable 1 active 2 standby 3 simplex 4 protected	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.15
cerCardAction Write-only action performed on this card.	CADANT-TCEqActionTyper/w Type Values: 0 notapplicable 1 initialize 2 switch 3 remove 4 restorecond 5 restoreuncd 6 systemreset 7 cardreset	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.17
cerCardTrapInh If a bit is set, the corresponding state change trap will not be sent.	Bitsr/w Enumerated Values: 0 primary 1 secondary 2 duplex 3 detected 4 tempoutofrange 5 tempnoreport 6 tempoverheat 7 overload	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.18
cerCardNumPorts Number of ports this card contains.	Integer32 Constraints: range: 0-1000	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.19
cerCardDetected CardType dectected automatically by the CMTS.	CADANT-TCCerCardType Type Values: 0 invalid 1 fan 2 pem 3 ccm 4 cdm 5 sam 6 rsm 7 ucam 8 dcam 98 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.20
cerCardSubDetected CardSubType dectected automatically by the CMTS.	CADANT-TCCerCardSubType Type Values: 0 invalid 1 fan 2 pem 3 ccm 4 cdm 5 sam 6 rsm10g 7 ucam96m24c 8 dcam192m8cAnnexA 9 dcam256m8cAnnexB 98 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.21
cerCardFwUpdateStatus Set to TRUE if a firmware update is in progress or has been done, else set to FALSE.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.23
cerCardSpareGroupId The cardId of the spare group leader for this sparing group. This value will be set to the invalid card id for all cards not associated with a sparing group.	CADANT-TCCardIdr/w Type Constraints: range: 0..99	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.24
cerCardSpareGroupMode The admin mode of the spare group leader for this sparing group. This value will be set to the invalid card id for all cards not associated with a sparing group.	Enumerationr/w Enumerated Values: 0 invalid 1 manual 2 auto	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.25
cerCardUpTime The value of sysUpTime when the primary state for this card made a transition from OOS to IS.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.26
cerCardTemperature The current relative temperature of the card. (1=coolest, 10=hottest)	Integer32 Constraints: range: 999-999 range: 1-10	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.29
cerCardPicDetected The type of PIC detected in this slot.	CADANT-TCCerPicType Type Values: 0 invalid 1 dcamLowPic8c 2 dcamHighPic8c 3 dcamSparePic8c 4 ucamHighPic24c 5 ucamSparePic24c 6 rsmPic 98 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.40
cerCardLastResetReason The reason for the latest card recovery.	OctetString Constraints: range: 0-64	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.43
cerCardTemperatureHighWarn The relative temperature of the card at which warnings are generated.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.44
cerCardTemperatureHighError The relative temperature of the card at which recoveries are initiated.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.45
cerCardAnnex The annex of the downstream channels associated with the card.	Enumeration Enumerated Values: 1 unknown 2 other 3 annexA 4 annexB 5 annexC	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.46
cerCardNumRfConnectors Number of RF ports this card contains.	Integer32 Constraints: range: 0-48	.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.47

A table of Port information.

cerPortEntry row .1.3.6.1.4.1.4998.1.1.10.1.4.13.1

A conceptual row containing pertinent information about a cerPort
owned by a card.

Indexes

cerPortCardId cerPortId

Column	Syntax	OID
cerPortCardId The unique id of the card this cerPort belongs to.	CADANT-TCCardId Type Constraints: range: 0..99	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.2
cerPortId The unique id of this cerPort within a card. the the cardId and cerPortId uniquely identify a port	CADANT-TCPortId Type Constraints: range: 0..392	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.3
cerPortType Type of this cerPort.	CADANT-TCCerPortTyper/w Type Values: 0 invalid 1 ureceiver 2 uchannel 3 eport10BaseT 4 eport100BaseT 5 eport1000BaseT 6 eport10000BaseT 8 macport 9 dchannelDocsis 10 dchannelVideo 11 linkAgg 12 dchannelVideoreplica 13 dchannelOfdm 98 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.4
cerPortAdminState The Admin state of this cerPort	CADANT-TCAdminStater/w Type Values: 1 up 2 down	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.6
cerPortPrState The primary state of this cerPort	CADANT-TCPrimaryState Type Values: 1 is 2 oos	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.7
cerPortSecState The secondary state of this cerPort	CADANT-TCSecondaryState Type Values: 0 notapplicable 1 manual 2 fault 3 diagnostic 4 overload 5 normal 6 degrade 7 initializing 8 swdownload 9 firmwarepump 10 powerup 11 bootdkm	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.8
cerPortDplxStatus The port Duplexing status.	CADANT-TCDuplexStatus Type Values: 0 notapplicable 1 active 2 standby 3 simplex 4 protected	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.9
cerPortAction Write-only action performed on a Port.	CADANT-TCEqActionTyper/w Type Values: 0 notapplicable 1 initialize 2 switch 3 remove 4 restorecond 5 restoreuncd 6 systemreset 7 cardreset	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.11
cerPortTrapInh If a bit is set, the corresponding state change trap will not be sent.	Bitsr/w Enumerated Values: 0 primary 1 secondary 2 duplex 3 linkUpLinkDown	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.12
cerPortNumChans Number of channels this cerPort contains.	Integer32 Constraints: range: 0-50	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.13
cerPortDocsIfIndex This object indicates the location of an interface in the cerPort table that represents this port. A value of 0 indicates that this cerPort does not have an association in the Iftable.	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.14
cerPortMacAddress The physical address value for this card. This value is used to populate the ifPhysAddress field in the IfTable and other Tables in docsis RFC MIBs.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.15
cerPortMode The desired operating mode of an ethernet cerPort. Not yet implemented.	CADANT-TCPortModer/w Type Values: 0 invalid 1 autoNegotiate 2 fullDuplex100Mpbs 3 halfDuplex100Mpbs 4 fullDuplex10Mpbs 5 halfDuplex10Mpbs 6 fullDuplex1000Mpbs 7 halfDuplex1000Mpbs 8 fullDuplex10000Mpbs	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.16
cerPortDetectedMode The current operating mode of an ethernet cerPort.	CADANT-TCPortDetectedMode Type Values: 0 invalid 2 fullDuplex100Mpbs 3 halfDuplex100Mpbs 4 fullDuplex10Mpbs 5 halfDuplex10Mpbs 6 fullDuplex1000Mpbs 7 halfDuplex1000Mpbs 8 fullDuplex10000Mpbs 9 sfpFullDuplex1000BaseT 10 sfpHalfDuplex1000BaseT 11 sfpFullDuplex100BaseT 12 sfpHalfDuplex100BaseT 13 sfpFullDuplex10BaseT 14 sfpHalfDuplex10BaseT 15 sfpFullDuplex1000BaseSX 16 sfpFullDuplex1000BaseLX 17 sfpFullDuplex1000BaseLH 18 sfpFullDuplex1000BaseLXLH 19 sfpFullDuplex1000BaseZX 20 sfpFullDuplex1000BaseCWDM 21 sfpFullDuplex1000BaseDWDM 22 xfpFullDuplex10GBaseSR 23 xfpFullDuplex10GBaseLRM 24 xfpFullDuplex10GBaseLR 25 xfpFullDuplex10GBaseER 26 xfpFullDuplex10GBaseZR 27 xfpFullDuplex10GBaseLX4 28 xfpFullDuplex10GBaseDWDM 29 sfpFullDuplex10GBaseSR 30 sfpFullDuplex10GBaseLRM 31 sfpFullDuplex10GBaseLR 32 sfpFullDuplex10GBaseER 33 sfpFullDuplex10GBaseZR 34 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.17
cerPortBgpId The bridge group cerPort id for this port.	Integer32 Constraints: range: -2147483647-2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.19
cerPortConnectorId For a DOCSIS or EQAM type port, this is the rear PIC connector. Otherwise, the value of this object is invalid.	CADANT-TCPortIdr/w Type Constraints: range: 0..392	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.20
cerPortCardSubType The CardSubType of the card this cerPort belongs to.	CADANT-TCCerCardSubType Type Values: 0 invalid 1 fan 2 pem 3 ccm 4 cdm 5 sam 6 rsm10g 7 ucam96m24c 8 dcam192m8cAnnexA 9 dcam256m8cAnnexB 98 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.21
cerPortDescription A persistent copy of ifAlias for this interface.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.27
cerPortCurrDsPower The latest downstream power level reported by the port. This is valid on for ports of type dport.	DOCS-IF-MIBTenthdBmV	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.28
cerPortMinDsPower The latest downstream power level recerPorted by the port. This is valid only for downstream ports.	DOCS-IF-MIBTenthdBmV	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.29
cerPortMaxDsPower The latest downstream power level recerPorted by the port. This is valid only for downstream ports.	DOCS-IF-MIBTenthdBmV	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.30
cerPortTxFlowControlMode The transmit flow control settings for this port (network ports only).	CADANT-TCFlowControlModer/w Type Values: 0 invalid 1 on 2 off 3 desired 4 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.31
cerPortRxFlowControlMode The receive flow control settings for this port (network ports only).	CADANT-TCFlowControlModer/w Type Values: 0 invalid 1 on 2 off 3 desired 4 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.32
cerPortTxFlowControlDetected The recerPorted transmit flow control settings for this port (network ports only).	CADANT-TCFlowControlMode Type Values: 0 invalid 1 on 2 off 3 desired 4 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.33
cerPortRxFlowControlDetected The recerPorted receive flow control settings for this port (network ports only).	CADANT-TCFlowControlMode Type Values: 0 invalid 1 on 2 off 3 desired 4 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.34
cerPortMacIfIndex The MAC IfIndex currently associcated with the upstream or downstream port.	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.35
cerPortGroupId The unique id of port group associated with this port.	CADANT-TCPortId Type Constraints: range: 0..392	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.36
cerPortGroupPortId The unique id of this port in the port group.	CADANT-TCPortId Type Constraints: range: 0..392	.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.37

A table of disk volume information.

cerDiskVolumeEntry row .1.3.6.1.4.1.4998.1.1.10.1.4.14.1

A conceptual row containing pertinent information about a disk volume

Indexes

cerDiskVolumeCardId cerDiskVolumeDriveId cerDiskVolumeId

Column	Syntax	OID
cerDiskVolumeCardId The unique id of the card this disk volume belongs to.	CADANT-TCCardId Type Constraints: range: 0..99	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.2
cerDiskVolumeDriveId The unique id of the disk drive this disk volume belongs to. A value of 99 indicates an invalid disk drive	Integer32 Constraints: range: 1-99	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.3
cerDiskVolumeId The unique id of this disk volume. the cerDiskVolumeCardId, the diskVolumeDiskId, and the. A value of 99 indicate an invalid volume	Integer32 Constraints: range: 1-99	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.4
cerDiskVolumeName The name of the disk volume.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.5
cerDiskVolumeSize The disk volume size in units of 2048 bytes.	bytesSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.6
cerDiskVolumeUsageLevel The disk volume usage level.	CADANT-TCDiskVolumeUsageLevel Type Values: 1 normal 2 minor 3 major 4 critical	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.7
cerDiskVolumeUsagePercentage The disk volume usage percentage.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.8
cerDiskVolumeUsageCriticalThreshold Usage percentage level when exceed will cause a cerDiskVolumeUsageNotification trap to be sent with cerDiskVolumeUsageLevel of diskVolumeUsageCritical.	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.9
cerDiskVolumeUsageMajorThreshold Usage percentage level when exceed will cause a cerDiskVolumeUsageNotification trap to be sent with cerDiskVolumeUsageLevel of diskVolumeUsageMajor.	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.10
cerDiskVolumeUsageMinorThreshold Usage percentage level when exceed will cause a cerDiskVolumeUsageNotification trap to be sent with cerDiskVolumeUsageLevel of diskVolumeUsageMinor.	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.11
cerDiskVolumeAutoDeleteUnusedFile When set to TRUE to the system will automatically delete unused files when cerDiskVolumeUsage exceed the cerDiskVolumeUsageCriticalThreshold value.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.12
cerDiskVolumeTrapInh If a bit is set, the corresponding trap will not be sent.	Bitsr/w Enumerated Values: 0 criticalUsageLevel 1 majorUsageLevel 2 minorUsageLevel 3 autoDeleteFiles	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.13
cerDiskVolumeDiskSize Total physical disk capacity in bytes.	bytesSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.14

This table shows the contains version information for the modules installed.

cerCardDataEntry row .1.3.6.1.4.1.4998.1.1.10.1.4.16.1

A conceptual row containing pertinent information about a card or
a circuit pack.

Indexes

No indexes recorded

Column	Syntax	OID
cerCardDataSerialNum This is the serial number of the card.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.1
cerCardDataFwVersion This is the firmware or FPGA version number of the card.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.2
cerCardDataHwVersion This is the hardware version of the card.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.3
cerCardDataHwDeviations This is the set of hardware deviations for the card.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.4
cerCardDataSwVersion This is the software version of the card.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.5
cerCardDataCpuType The current CPU type of the card.	OctetString Constraints: range: 0-25	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.6
cerCardDataCpuSpeed The current CPU speed of the card.	MHzSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.7
cerCardDataBusSpeed The current bus speed of the card.	hertzSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.8
cerCardDataRamSize The current size of installed RAM of the card.	megabytesSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.9
cerCardDataNorFlashSize The current size of installed FLASH of the card.	bytesSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.10
cerCardDataNandFlashSize The current size of installed FLASH of the card.	bytesSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.11
cerCardDataFpgaSource The source of the running version of the FPGAs on the card.	CADANT-TCFirmwareSource Type Values: 1 committed 2 transient 3 boot1 4 boot2 5 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.12
cerCardDataBootVersion The current versions of the boot loaders installed on the card.	OctetString Constraints: range: 0-90	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.13
cerCardDataLastBootVersion The last version of the boot loader used on the card.	OctetString Constraints: range: 0-90	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.14
cerCardDataLastBootSource The source of the version of the bootloader last used on the card.	CADANT-TCFirmwareSource Type Values: 1 committed 2 transient 3 boot1 4 boot2 5 unknown	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.15
cerCardDataPicSerialNum This is the serial number of the PIC.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.16
cerCardDataPicHwVersion This is the hardware version of the PIC.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.17
cerCardDataPicHwDeviations This is the set of hardware deviations for the PIC.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.18
cerCardDataPicModelNum This is the model number of the PIC.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.19
cerCardDataMfgDateTime Date of the module's manufacture (FRU).	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.20
cerCardDataMfg Name of the manufacturer (FRU).	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.21
cerCardDataProductName Name of the product (FRU).	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.22
cerCardDataPartModelNum Name of the model of this product (FRU).	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.23
cerCardDataProductVersion Version of the model of this product (FRU).	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.24
cerCardDataAssetTag Asset tag of this part (FRU).	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.25
cerCardDataCommittedSwVersion This is the software version of the card.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.26
cerCardDataFeedAPresent This object indicates whether power feed A is present or not.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.27
cerCardDataFeedBPresent This object indicates whether power feed B is present or not.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.28
cerCardDataAllowedPorts This object indicates the allowed number of licensed ports.	Unsigned32 Constraints: range: 0-5000	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.29
cerCardDataLicenseAnnex This object shows the annex associated with the license.	Enumeration Enumerated Values: 1 unknown 2 other 3 annexA 4 annexB 5 annexC	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.30
cerCardDataLicensePorts This object indicates the number of ports associated with the license.	Unsigned32 Constraints: range: 0-5000	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.31
cerCardDataLicenseDate This object indicates the date associated with the license.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.32
cerCardDataPatchVersions This is the patch version(s) running on the card.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.33
cerCardDataPicModelName This is the model name of the PIC.	OctetString Constraints: range: 0-64	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.34
cerCardDataPicMfgRevision This is the manufacture revision of the PIC.	OctetString Constraints: range: 0-64	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.35
cerCardDataPicMfg This is the manufacturer of the PIC.	OctetString Constraints: range: 0-64	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.36
cerCardDataPicMfgDateTime This object indicates the date associated with the PIC.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.37

Status information for the E6 fans.

cerFanStatusEntry row .1.3.6.1.4.1.4998.1.1.10.1.4.17.1

A conceptual row containing information about one of the fans.

Indexes

cerCardId

Column	Syntax	OID
cerFan1Speed The last measured speed of fan1.	rpmInteger32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.17.1.1
cerFan2Speed The last measured speed of fan2.	rpmInteger32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.17.1.2
cerFan3Speed The last measured speed of fan3.	rpmInteger32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.17.1.3
cerFanLevel The last measured speed level of fans.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.4998.1.1.10.1.4.17.1.4
cerFanAmbientTemperature The last measured ambient temperature of fans.	degrees CSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.17.1.5

PEM Status information for the E6 power modules.

cerPemStatusEntry row .1.3.6.1.4.1.4998.1.1.10.1.4.18.1

A conceptual row containing information about one of the power modules.

Indexes

cerCardId

Column	Syntax	OID
cerPemLedStatus LED status of the PEM	Enumeration Enumerated Values: 1 normal 2 alarm	.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.1
cerPemFeed1Voltage Feed 1 voltage	decivoltSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.2
cerPemFeed1Current Feed 1 current	deciiampSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.3
cerPemFeed2Voltage Feed 2 voltage	decivoltSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.4
cerPemFeed2Current Feed 2 current	deciampSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.5
cerPemFeed1Present Feed 1 presence	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.6
cerPemFeed2Present Feed 2 presence	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.7
cerPemCircuitBreaker1Enable circuit breaker 1 presence	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.8
cerPemCircuitBreaker2Enable circuit breaker 2 presence	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.9
cerPemBranchPresent brach A through I presence	Bits Enumerated Values: 0 a 1 b 2 c 3 d 4 e 5 f 6 g 7 h 8 i	.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.10

A table of test available for a card.

cardTestEntry row .1.3.6.1.4.1.4998.1.1.10.1.5.3.1

A conceptual row containing information about tests or dignostics available for
a card.

Indexes

cardTestIndex cardTestId

Column	Syntax	OID
cardTestIndex Card Identification Number taken from the CardTable. Used as index.	CADANT-TCCardId Type Constraints: range: 0..99	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.2
cardTestId Test Identification Number. Used as index to test table	TestId Type Constraints: range: 1..100	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.3
cardTestName A unique name for this test.	OctetString Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.4
cardTestType Test Type.	TestType Type Values: 1 test 2 diagnostic 3 unknown	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.5
cardTestDescription A short description of the test.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.6
cardTestCommand Command to be execute this test on this shelf	TestCommandr/w Type Values: 1 noop 2 stop 3 disable 4 enable 5 runNow	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.7
cardTestScheduleCommand Schedule Command to be execute this test on this shelf	TestScheduleCommandr/w Type Values: 1 noop 2 disable 3 enable	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.8
cardTestSchedule Test Scheduling.	TestScheduler/w	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.9
cardTestTime Test start time.	SNMPv2-TCDateAndTimer/w Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.10
cardTestResult Result of the test.	TestResult Type Values: 1 notRun 2 inProgress 3 pass 4 fail 5 inconclusive 6 timeOut 7 abort	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.11
cardTestResultDesc Additional information of the test result.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.12
cardTestTransId Test transaction Id.	TestTransactionIdr/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.13

A table of test available for a card.

auditEntry row .1.3.6.1.4.1.4998.1.1.10.1.6.4.1

A conceptual row contains information about Audits.

Indexes

auditCardId auditId

Column	Syntax	OID
auditCardId Card Identification Number taken from the CardTable. Used as index.	CADANT-TCCardId Type Constraints: range: 0..99	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.2
auditId Unique ID of the internal Audit	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.3
auditName Name of the internal Audit	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.4
auditDescription Description of the Audit	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.5
auditTime Start time of the audit.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.6
auditCommand Audit Commands. The runnow command will stop the currently running audit sequence and start executing requested audit immediated. If enabled, automatic audit schedule will be restarted.	Enumerationr/w Enumerated Values: 1 enable 2 disable 4 runnow	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.7
auditStatus Audit status.	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.8
auditResult Audit Result.	Enumeration Enumerated Values: 1 passed 2 failed 4 abort 5 notRun	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.9
auditPassedCount Number of passed entry during previous audit run.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.10
auditFailedCount Number of failed entry during previous audit run.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.11
auditCycleCount Number of audit run completed.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.12
auditTotalPassedCount Number of cumulative passed entry of all audit runs.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.13
auditTotalFailedCount Number of cumulative failed entry of all audit runs.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.14

Overrides default handling of FPGA error events.

fpgaErrorEventEntry row .1.3.6.1.4.1.4998.1.1.10.1.9.1.1

A conceptual row containing information about FPGA error event handling.

Indexes

errEvCardId errEventId

Column	Syntax	OID
errEventId Event ID associated with the FPGA error. A row in this table defines behavior for a specific FPGA error that overrides the default behavior of the system.	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.1
errEvRecoveryEnabled If true, the card can be recovered when this FPGA error is detected. When the card is recovered depends on the setting of errEvRecoveryThreshold. If this value is false, the card will not be recovered when this error i…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.2
errEvLoggingEnabled If true, the card will provide notification of the occurance of the this error. When the notification occurs is dependent on the setting of errEvLogThrottleThreshold. The severity of the notification is determined b…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.3
errEvLogLevel If errEvLoggingEnabled is true, this setting sets the severity level of the generated notification. In general, higher values indicate lower severity.	Integer32r/w Constraints: range: 1-8	.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.4
errEvRowStatus The only set actions supported on this table are createAndGo(4) and destroy(6).	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.5
errEvCardId The unique id of this card within the shelf.	CADANT-TCCardId Type Constraints: range: 0..99	.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.6

Allows overriding the configured sparing mode for a spare group
based on the fault type that caused the sparing event.

cerSpareModeExtEntry row .1.3.6.1.4.1.4998.1.1.10.1.11.1.1

A conceptual row containing information about sparing overrides for a spare group.

Indexes

cerSpareModeCardId cerSpareModeFaultId

Column	Syntax	OID
cerSpareModeCardId The cardId of the spare group leader for this override.	CADANT-TCCardId Type Constraints: range: 0..99	.1.3.6.1.4.1.4998.1.1.10.1.11.1.1.1
cerSpareModeFaultId The fault group associated with the override behavior. When an event occurs that would normally trigger a card reset and a sparing event and that event is in the configured fault group, the mode configured in the cerCar…	Enumeration Enumerated Values: 0 none 1 pingFault 2 initTimeout 3 ersmFault 4 swException 5 bcm3142Err 6 dulFailure 7 dataplaneFailure 8 dsUnderPower 9 dsOverPower 10 sbecOverflow 11 deviceFatal 12 fpgaFatalError 13 clockLost 14 pwrSensorHighFault 15 pwrSensorLowFault 16 fpgaBufferPoolFault 17 dataplaneLinkFault 18 monitoredTaskFailure	.1.3.6.1.4.1.4998.1.1.10.1.11.1.1.2
cerSpareModeMode The sparing mode that should be enforced when an error in the configured catagory occurs that results in a sparing event.	Enumerationr/w Enumerated Values: 0 invalid 1 manual 2 auto	.1.3.6.1.4.1.4998.1.1.10.1.11.1.1.3
cerSpareModeRowStatus The only set actions supported on this table are createAndGo(4) and destroy(6).	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.10.1.11.1.1.4