ATM-MIB Table View

This table contains ATM local interface
configuration parameters, one entry per ATM
interface port.

atmInterfaceConfEntry row .1.3.6.1.2.1.37.1.2.1

This list contains ATM interface configuration
parameters and state variables and is indexed
by ifIndex values of ATM interfaces.

Indexes

IF-MIBifIndex

Column	Syntax	OID
atmInterfaceMaxVpcs The maximum number of VPCs (PVPCs and SVPCs) supported at this ATM interface. At the ATM UNI, the maximum number of VPCs (PVPCs and SVPCs) ranges from 0 to 256 only.	Integer32r/w Constraints: range: 0-4096	.1.3.6.1.2.1.37.1.2.1.1
atmInterfaceMaxVccs The maximum number of VCCs (PVCCs and SVCCs) supported at this ATM interface.	Integer32r/w Constraints: range: 0-65536	.1.3.6.1.2.1.37.1.2.1.2
atmInterfaceConfVpcs The number of VPCs (PVPC, Soft PVPC and SVPC) currently in use at this ATM interface. It includes the number of PVPCs and Soft PVPCs that are configured at the interface, plus the number of SVPCs that are currently es…	Integer32 Constraints: range: 0-4096	.1.3.6.1.2.1.37.1.2.1.3
atmInterfaceConfVccs The number of VCCs (PVCC, Soft PVCC and SVCC) currently in use at this ATM interface. It includes the number of PVCCs and Soft PVCCs that are configured at the interface, plus the number of SVCCs that are currently es…	Integer32 Constraints: range: 0-65536	.1.3.6.1.2.1.37.1.2.1.4
atmInterfaceMaxActiveVpiBits The maximum number of active VPI bits configured for use at the ATM interface. At the ATM UNI, the maximum number of active VPI bits configured for use ranges from 0 to 8 only.	Integer32r/w Constraints: range: 0-12	.1.3.6.1.2.1.37.1.2.1.5
atmInterfaceMaxActiveVciBits The maximum number of active VCI bits configured for use at this ATM interface.	Integer32r/w Constraints: range: 0-16	.1.3.6.1.2.1.37.1.2.1.6
atmInterfaceIlmiVpi The VPI value of the VCC supporting the ILMI at this ATM interface. If the values of atmInterfaceIlmiVpi and atmInterfaceIlmiVci are both equal to zero then the ILMI is not supported at this ATM interface.	ATM-TC-MIBAtmVpIdentifierr/w Type Constraints: range: 0..4095	.1.3.6.1.2.1.37.1.2.1.7
atmInterfaceIlmiVci The VCI value of the VCC supporting the ILMI at this ATM interface. If the values of atmInterfaceIlmiVpi and atmInterfaceIlmiVci are both equal to zero then the ILMI is not supported at this ATM interface.	ATM-TC-MIBAtmVcIdentifierr/w Type Constraints: range: 0..65535	.1.3.6.1.2.1.37.1.2.1.8
atmInterfaceAddressTypedeprecated The type of primary ATM address configured for use at this ATM interface.	Enumeration Enumerated Values: 1 private 2 nsapE164 3 nativeE164 4 other	.1.3.6.1.2.1.37.1.2.1.9
atmInterfaceAdminAddressdeprecated The primary address assigned for administrative purposes, for example, an address associated with the service provider side of a public network UNI (thus, the value of this address corresponds with the value of ifPhysAd…	ATM-TC-MIBAtmAddr Type Constraints: range: 0..40	.1.3.6.1.2.1.37.1.2.1.10
atmInterfaceMyNeighborIpAddress The IP address of the neighbor system connected to the far end of this interface, to which a Network Management Station can send SNMP messages, as IP datagrams sent to UDP port 161, in order to access network managemen…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.2.1.37.1.2.1.11
atmInterfaceMyNeighborIfName The textual name of the interface on the neighbor system on the far end of this interface, and to which this interface connects. If the neighbor system is manageable through SNMP and supports the object ifName, the val…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.2.1.37.1.2.1.12
atmInterfaceCurrentMaxVpiBits The maximum number of VPI Bits that may currently be used at this ATM interface. The value is the minimum of atmInterfaceMaxActiveVpiBits, and the atmInterfaceMaxActiveVpiBits of the interface's UNI/NNI peer. …	Integer32 Constraints: range: 0-12	.1.3.6.1.2.1.37.1.2.1.13
atmInterfaceCurrentMaxVciBits The maximum number of VCI Bits that may currently be used at this ATM interface. The value is the minimum of atmInterfaceMaxActiveVciBits, and the atmInterfaceMaxActiveVciBits of the interface's UNI/NNI peer. …	Integer32 Constraints: range: 0-16	.1.3.6.1.2.1.37.1.2.1.14
atmInterfaceSubscrAddress The identifier assigned by a service provider to the network side of a public network UNI. If this interface has no assigned service provider address, or for other interfaces this is an octet string of zero length.	ATM-TC-MIBAtmAddrr/w Type Constraints: range: 0..40	.1.3.6.1.2.1.37.1.2.1.15

This table contains ATM interface DS3 PLCP
parameters and state variables, one entry per
          
ATM interface port.

atmInterfaceDs3PlcpEntry row .1.3.6.1.2.1.37.1.3.1

This list contains DS3 PLCP parameters and
state variables at the ATM interface and is
indexed by the ifIndex value of the ATM interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
atmInterfaceDs3PlcpSEFSs The number of DS3 PLCP Severely Errored Framing Seconds (SEFS). Each SEFS represents a one-second interval which contains one or more SEF events.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.37.1.3.1.1
atmInterfaceDs3PlcpAlarmState This variable indicates if there is an alarm present for the DS3 PLCP. The value receivedFarEndAlarm means that the DS3 PLCP has received an incoming Yellow Signal, the value incomingLOF means that the DS3 PLCP has dec…	Enumeration Enumerated Values: 1 noAlarm 2 receivedFarEndAlarm 3 incomingLOF	.1.3.6.1.2.1.37.1.3.1.2
atmInterfaceDs3PlcpUASs The counter associated with the number of Unavailable Seconds encountered by the PLCP.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.37.1.3.1.3

This table contains ATM interface TC
Sublayer parameters and state variables,
one entry per ATM interface port.

atmInterfaceTCEntry row .1.3.6.1.2.1.37.1.4.1

This list contains TC Sublayer parameters
and state variables at the ATM interface and is
indexed by the ifIndex value of the ATM interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
atmInterfaceOCDEvents The number of times the Out of Cell Delineation (OCD) events occur. If seven consecutive ATM cells have Header Error Control (HEC) violations, an OCD event occurs. A high number of OCD events may indicate a problem wit…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.37.1.4.1.1
atmInterfaceTCAlarmState This variable indicates if there is an alarm present for the TC Sublayer. The value lcdFailure(2) indicates that the TC Sublayer is currently in the Loss of Cell Delineation (LCD) defect maintenance state. The value n…	Enumeration Enumerated Values: 1 noAlarm 2 lcdFailure	.1.3.6.1.2.1.37.1.4.1.2

This table contains information on ATM traffic
descriptor type and the associated parameters.

atmTrafficDescrParamEntry row .1.3.6.1.2.1.37.1.5.1

This list contains ATM traffic descriptor
type and the associated parameters.

Indexes

atmTrafficDescrParamIndex

Column	Syntax	OID
atmTrafficDescrParamIndex This object is used by the virtual link table (i.e., VPL or VCL table) to identify the row of this table. When creating a new row in the table the value of this index may be obtained by retrieving the value of atmTraffi…	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.2.1.37.1.5.1.1
atmTrafficDescrType The value of this object identifies the type of ATM traffic descriptor. The type may indicate no traffic descriptor or traffic descriptor with one or more parameters. These parameters are specified as a parameter vector…	ObjectIdentifierr/w	.1.3.6.1.2.1.37.1.5.1.2
atmTrafficDescrParam1 The first parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.2.1.37.1.5.1.3
atmTrafficDescrParam2 The second parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.2.1.37.1.5.1.4
atmTrafficDescrParam3 The third parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.2.1.37.1.5.1.5
atmTrafficDescrParam4 The fourth parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.2.1.37.1.5.1.6
atmTrafficDescrParam5 The fifth parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.2.1.37.1.5.1.7
atmTrafficQoSClassdeprecated The value of this object identifies the QoS Class. Four Service classes have been specified in the ATM Forum UNI Specification: Service Class A: Constant bit rate video and Circuit emulation Service Cla…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.2.1.37.1.5.1.8
atmTrafficDescrRowStatus This object is used to create a new row or modify or delete an existing row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.37.1.5.1.9
atmServiceCategory The ATM service category.	ATM-TC-MIBAtmServiceCategoryr/w Type Values: 1 other 2 cbr 3 rtVbr 4 nrtVbr 5 abr 6 ubr	.1.3.6.1.2.1.37.1.5.1.10
atmTrafficFrameDiscard If set to 'true', this object indicates that the network is requested to treat data for this connection, in the given direction, as frames (e.g. AAL5 CPCS_PDU's) rather than as individual cells. While the precise imple…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.37.1.5.1.11

The Virtual Path Link (VPL) table.  A
bi-directional VPL is modeled as one entry
in this table. This table can be used for
PVCs, SVCs and Soft PVCs.
Entries are not present in this table for
the VPIs used by entries in the atmVclTable.

atmVplEntry row .1.3.6.1.2.1.37.1.6.1

An entry in the VPL table. This entry is
used to model a bi-directional VPL.
To create a VPL at an ATM interface,
either of the following procedures are used:

Negotiated VPL establishment

(1) …

Indexes

IF-MIBifIndex atmVplVpi

Column	Syntax	OID
atmVplVpi The VPI value of the VPL.	ATM-TC-MIBAtmVpIdentifier Type Constraints: range: 0..4095	.1.3.6.1.2.1.37.1.6.1.1
atmVplAdminStatus This object is instanciated only for a VPL which terminates a VPC (i.e., one which is NOT cross-connected to other VPLs). Its value specifies the desired administrative state of the VPL.	ATM-TC-MIBAtmVorXAdminStatusr/w Type Values: 1 up 2 down	.1.3.6.1.2.1.37.1.6.1.2
atmVplOperStatus The current operational status of the VPL.	ATM-TC-MIBAtmVorXOperStatus Type Values: 1 up 2 down 3 unknown	.1.3.6.1.2.1.37.1.6.1.3
atmVplLastChange The value of sysUpTime at the time this VPL entered its current operational state.	ATM-TC-MIBAtmVorXLastChange	.1.3.6.1.2.1.37.1.6.1.4
atmVplReceiveTrafficDescrIndex The value of this object identifies the row in the atmTrafficDescrParamTable which applies to the receive direction of the VPL.	ATM-TC-MIBAtmTrafficDescrParamIndexr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.37.1.6.1.5
atmVplTransmitTrafficDescrIndex The value of this object identifies the row in the atmTrafficDescrParamTable which applies to the transmit direction of the VPL.	ATM-TC-MIBAtmTrafficDescrParamIndexr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.37.1.6.1.6
atmVplCrossConnectIdentifier This object is instantiated only for a VPL which is cross-connected to other VPLs that belong to the same VPC. All such associated VPLs have the same value of this object, and all their cross-connections are identified…	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.37.1.6.1.7
atmVplRowStatus This object is used to create, delete or modify a row in this table. To create a new VCL, this object is initially set to 'createAndWait' or 'createAndGo'. This object should not be set to 'active' unless the following…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.37.1.6.1.8
atmVplCastType The connection topology type.	ATM-TC-MIBAtmConnCastTyper/w Type Values: 1 p2p 2 p2mpRoot 3 p2mpLeaf	.1.3.6.1.2.1.37.1.6.1.9
atmVplConnKind The use of call control.	ATM-TC-MIBAtmConnKindr/w Type Values: 1 pvc 2 svcIncoming 3 svcOutgoing 4 spvcInitiator 5 spvcTarget	.1.3.6.1.2.1.37.1.6.1.10

The Virtual Channel Link (VCL) table.  A
bi-directional VCL is modeled as one entry
in this table. This table can be used for
PVCs, SVCs and Soft PVCs.

atmVclEntry row .1.3.6.1.2.1.37.1.7.1

An entry in the VCL table. This entry is
used to model a bi-directional VCL.
To create a VCL at an ATM interface,
either of the following procedures are used:

Negotiated VCL establishment

(1) T…

Indexes

IF-MIBifIndex atmVclVpi atmVclVci

Column	Syntax	OID
atmVclVpi The VPI value of the VCL.	ATM-TC-MIBAtmVpIdentifier Type Constraints: range: 0..4095	.1.3.6.1.2.1.37.1.7.1.1
atmVclVci The VCI value of the VCL.	ATM-TC-MIBAtmVcIdentifier Type Constraints: range: 0..65535	.1.3.6.1.2.1.37.1.7.1.2
atmVclAdminStatus This object is instanciated only for a VCL which terminates a VCC (i.e., one which is NOT cross-connected to other VCLs). Its value specifies the desired administrative state of the VCL.	ATM-TC-MIBAtmVorXAdminStatusr/w Type Values: 1 up 2 down	.1.3.6.1.2.1.37.1.7.1.3
atmVclOperStatus The current operational status of the VCL.	ATM-TC-MIBAtmVorXOperStatus Type Values: 1 up 2 down 3 unknown	.1.3.6.1.2.1.37.1.7.1.4
atmVclLastChange The value of sysUpTime at the time this VCL entered its current operational state.	ATM-TC-MIBAtmVorXLastChange	.1.3.6.1.2.1.37.1.7.1.5
atmVclReceiveTrafficDescrIndex The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCL.	ATM-TC-MIBAtmTrafficDescrParamIndexr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.37.1.7.1.6
atmVclTransmitTrafficDescrIndex The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VCL.	ATM-TC-MIBAtmTrafficDescrParamIndexr/w Type Constraints: range: 0..2147483647	.1.3.6.1.2.1.37.1.7.1.7
atmVccAalType An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL is in use. The type of AAL used on this VCC. The AAL type includes AAL1, AAL2, AAL3/4, and AAL5. The other(4) may be…	Enumerationr/w Enumerated Values: 1 aal1 2 aal34 3 aal5 4 other 5 unknown 6 aal2	.1.3.6.1.2.1.37.1.7.1.8
atmVccAal5CpcsTransmitSduSize An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDU size in octets that is supported on the transmit direction of this VCC.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.2.1.37.1.7.1.9
atmVccAal5CpcsReceiveSduSize An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDU size in octets that is supported on the receive direction of this VCC.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.2.1.37.1.7.1.10
atmVccAal5EncapsType An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The type of data encapsulation used over the AAL5 SSCS layer. The definitions reference RFC 1483 Multipr…	Enumerationr/w Enumerated Values: 1 vcMultiplexRoutedProtocol 2 vcMultiplexBridgedProtocol8023 3 vcMultiplexBridgedProtocol8025 4 vcMultiplexBridgedProtocol8026 5 vcMultiplexLANemulation8023 6 vcMultiplexLANemulation8025 7 llcEncapsulation 8 multiprotocolFrameRelaySscs 9 other 10 unknown	.1.3.6.1.2.1.37.1.7.1.11
atmVclCrossConnectIdentifier This object is instantiated only for a VCL which is cross-connected to other VCLs that belong to the same VCC. All such associated VCLs have the same value of this object, and all their cross-connections are identified…	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.2.1.37.1.7.1.12
atmVclRowStatus This object is used to create, delete or modify a row in this table. To create a new VCL, this object is initially set to 'createAndWait' or 'createAndGo'. This object should not be set to 'active' unless the following…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.37.1.7.1.13
atmVclCastType The connection topology type.	ATM-TC-MIBAtmConnCastTyper/w Type Values: 1 p2p 2 p2mpRoot 3 p2mpLeaf	.1.3.6.1.2.1.37.1.7.1.14
atmVclConnKind The use of call control.	ATM-TC-MIBAtmConnKindr/w Type Values: 1 pvc 2 svcIncoming 3 svcOutgoing 4 spvcInitiator 5 spvcTarget	.1.3.6.1.2.1.37.1.7.1.15

The ATM VP Cross Connect table for PVCs.
An entry in this table models two
cross-connected VPLs.
Each VPL must have its atmConnKind set
to pvc(1).

atmVpCrossConnectEntry row .1.3.6.1.2.1.37.1.9.1

An entry in the ATM VP Cross Connect table.
This entry is used to model a bi-directional
ATM VP cross-connect which cross-connects
two VPLs.

Step-wise Procedures to set up a VP Cross-connect

On…

Indexes

atmVpCrossConnectIndex atmVpCrossConnectLowIfIndex atmVpCrossConnectLowVpi atmVpCrossConnectHighIfIndex atmVpCrossConnectHighVpi

Column	Syntax	OID
atmVpCrossConnectIndex A unique value to identify this VP cross-connect. For each VPL associated with this cross-connect, the agent reports this cross-connect index value in the atmVplCrossConnectIdentifier attribute of the corresponding atmV…	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.2.1.37.1.9.1.1
atmVpCrossConnectLowIfIndex The ifIndex value of the ATM interface for this VP cross-connect. The term low implies that this ATM interface has the numerically lower ifIndex value than the other ATM interface identified in the same atmVpCrossConnec…	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.2.1.37.1.9.1.2
atmVpCrossConnectLowVpi The VPI value at the ATM interface associated with the VP cross-connect that is identified by atmVpCrossConnectLowIfIndex.	ATM-TC-MIBAtmVpIdentifier Type Constraints: range: 0..4095	.1.3.6.1.2.1.37.1.9.1.3
atmVpCrossConnectHighIfIndex The ifIndex value of the ATM interface for this VP cross-connect. The term high implies that this ATM interface has the numerically higher ifIndex value than the other ATM interface identified in the same atmVpCrossCon…	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.2.1.37.1.9.1.4
atmVpCrossConnectHighVpi The VPI value at the ATM interface associated with the VP cross-connect that is identified by atmVpCrossConnectHighIfIndex.	ATM-TC-MIBAtmVpIdentifier Type Constraints: range: 0..4095	.1.3.6.1.2.1.37.1.9.1.5
atmVpCrossConnectAdminStatus The desired administrative status of this bi-directional VP cross-connect.	ATM-TC-MIBAtmVorXAdminStatusr/w Type Values: 1 up 2 down	.1.3.6.1.2.1.37.1.9.1.6
atmVpCrossConnectL2HOperStatus The operational status of the VP cross-connect in one direction; (i.e., from the low to high direction).	ATM-TC-MIBAtmVorXOperStatus Type Values: 1 up 2 down 3 unknown	.1.3.6.1.2.1.37.1.9.1.7
atmVpCrossConnectH2LOperStatus The operational status of the VP cross-connect in one direction; (i.e., from the high to low direction).	ATM-TC-MIBAtmVorXOperStatus Type Values: 1 up 2 down 3 unknown	.1.3.6.1.2.1.37.1.9.1.8
atmVpCrossConnectL2HLastChange The value of sysUpTime at the time this VP cross-connect entered its current operational state in the low to high direction.	ATM-TC-MIBAtmVorXLastChange	.1.3.6.1.2.1.37.1.9.1.9
atmVpCrossConnectH2LLastChange The value of sysUpTime at the time this VP cross-connect entered its current operational in the high to low direction.	ATM-TC-MIBAtmVorXLastChange	.1.3.6.1.2.1.37.1.9.1.10
atmVpCrossConnectRowStatus The status of this entry in the atmVpCrossConnectTable. This object is used to create a cross-connect for cross-connecting VPLs which are created using the atmVplTable or to change or delete an existing cross-connect. …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.37.1.9.1.11

The ATM VC Cross Connect table for PVCs.
An entry in this table models two
cross-connected VCLs.
Each VCL must have its atmConnKind set
to pvc(1).

atmVcCrossConnectEntry row .1.3.6.1.2.1.37.1.11.1

An entry in the ATM VC Cross Connect table.
This entry is used to model a bi-directional ATM
VC cross-connect cross-connecting two end points.

Step-wise Procedures to set up a VC Cross-connect

…

Indexes

atmVcCrossConnectIndex atmVcCrossConnectLowIfIndex atmVcCrossConnectLowVpi atmVcCrossConnectLowVci atmVcCrossConnectHighIfIndex atmVcCrossConnectHighVpi atmVcCrossConnectHighVci

Column	Syntax	OID
atmVcCrossConnectIndex A unique value to identify this VC cross-connect. For each VCL associated with this cross-connect, the agent reports this cross-connect index value in the atmVclCrossConnectIdentifier attribute of the corresponding atmV…	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.2.1.37.1.11.1.1
atmVcCrossConnectLowIfIndex The ifIndex value of the ATM interface for this VC cross-connect. The term low implies that this ATM interface has the numerically lower ifIndex value than the other ATM interface identified in the same atmVcCrossConnec…	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.2.1.37.1.11.1.2
atmVcCrossConnectLowVpi The VPI value at the ATM interface associated with the VC cross-connect that is identified by atmVcCrossConnectLowIfIndex.	ATM-TC-MIBAtmVpIdentifier Type Constraints: range: 0..4095	.1.3.6.1.2.1.37.1.11.1.3
atmVcCrossConnectLowVci The VCI value at the ATM interface associated with this VC cross-connect that is identified by atmVcCrossConnectLowIfIndex.	ATM-TC-MIBAtmVcIdentifier Type Constraints: range: 0..65535	.1.3.6.1.2.1.37.1.11.1.4
atmVcCrossConnectHighIfIndex The ifIndex value for the ATM interface for this VC cross-connect. The term high implies that this ATM interface has the numerically higher ifIndex value than the other ATM interface identified in the sam…	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.2.1.37.1.11.1.5
atmVcCrossConnectHighVpi The VPI value at the ATM interface associated with the VC cross-connect that is identified by atmVcCrossConnectHighIfIndex.	ATM-TC-MIBAtmVpIdentifier Type Constraints: range: 0..4095	.1.3.6.1.2.1.37.1.11.1.6
atmVcCrossConnectHighVci The VCI value at the ATM interface associated with the VC cross-connect that is identified by atmVcCrossConnectHighIfIndex.	ATM-TC-MIBAtmVcIdentifier Type Constraints: range: 0..65535	.1.3.6.1.2.1.37.1.11.1.7
atmVcCrossConnectAdminStatus The desired administrative status of this bi-directional VC cross-connect.	ATM-TC-MIBAtmVorXAdminStatusr/w Type Values: 1 up 2 down	.1.3.6.1.2.1.37.1.11.1.8
atmVcCrossConnectL2HOperStatus The current operational status of the VC cross-connect in one direction; (i.e., from the low to high direction).	ATM-TC-MIBAtmVorXOperStatus Type Values: 1 up 2 down 3 unknown	.1.3.6.1.2.1.37.1.11.1.9
atmVcCrossConnectH2LOperStatus The current operational status of the VC cross-connect in one direction; (i.e., from the high to low direction).	ATM-TC-MIBAtmVorXOperStatus Type Values: 1 up 2 down 3 unknown	.1.3.6.1.2.1.37.1.11.1.10
atmVcCrossConnectL2HLastChange The value of sysUpTime at the time this VC cross-connect entered its current operational state in low to high direction.	ATM-TC-MIBAtmVorXLastChange	.1.3.6.1.2.1.37.1.11.1.11
atmVcCrossConnectH2LLastChange The value of sysUpTime at the time this VC cross-connect entered its current operational state in high to low direction.	ATM-TC-MIBAtmVorXLastChange	.1.3.6.1.2.1.37.1.11.1.12
atmVcCrossConnectRowStatus The status of this entry in the atmVcCrossConnectTable. This object is used to create a new cross-connect for cross-connecting VCLs which are created using the atmVclTable or to change or delete existing cross-connect.…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.37.1.11.1.13

This table contains AAL5 VCC performance
parameters.

aal5VccEntry row .1.3.6.1.2.1.37.1.12.1

This list contains the AAL5 VCC
performance parameters and is indexed
by ifIndex values of AAL5 interfaces
and the associated VPI/VCI values.

Indexes

IF-MIBifIndex aal5VccVpi aal5VccVci

Column	Syntax	OID
aal5VccVpi The VPI value of the AAL5 VCC at the interface identified by the ifIndex.	ATM-TC-MIBAtmVpIdentifier Type Constraints: range: 0..4095	.1.3.6.1.2.1.37.1.12.1.1
aal5VccVci The VCI value of the AAL5 VCC at the interface identified by the ifIndex.	ATM-TC-MIBAtmVcIdentifier Type Constraints: range: 0..65535	.1.3.6.1.2.1.37.1.12.1.2
aal5VccCrcErrors The number of AAL5 CPCS PDUs received with CRC-32 errors on this AAL5 VCC at the interface associated with an AAL5 entity.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.37.1.12.1.3
aal5VccSarTimeOuts The number of partially re-assembled AAL5 CPCS PDUs which were discarded on this AAL5 VCC at the interface associated with an AAL5 entity because they were not fully re-assembled within the required time period. If the…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.37.1.12.1.4
aal5VccOverSizedSDUs The number of AAL5 CPCS PDUs discarded on this AAL5 VCC at the interface associated with an AAL5 entity because the AAL5 SDUs were too large.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.37.1.12.1.5