fsErpsRingConfigMultipleFailure

SUPERMICRO-ERPS-MIB · .1.3.6.1.4.1.10876.101.2.40.2.3.1.12

Object

column r/w Enumeration

This object is configured in interconnection node of the sub-ring to
support the feature 'Minimizing segmentation in interconnected rings'
as per Appendix X of ITU-T G.8032/Y.1344 (03/2010) standard.

Configured value of the objects fsErpsRingConfigInterConnNode and
fsErpsRingConfigMultipleFailure is used in Block Indication Logic Procedure
as per Section X.3.2 in Appendix X of ITU-T G.8032/Y.1344 (03/2010) standard.
interconnected rings as described below :
a) If Loss of connectivity between the interconnection nodes is detected
and if the objects fsErpsRingConfigInterConnNode and
fsErpsRingConfigMultipleFailure are configured to have identical
values(i.e both are set to either primary or secondary) then Local MS
command is applied on the subring port else loss of connectivity
between the interconnection nodes is ignored.
b) Similarly when loss of connectivity between the interconnection nodes
is recovered and if the objects fsErpsRingConfigInterConnNode and
fsErpsRingConfigMultipleFailure are configured to have identical values
(i.e both are set to either primary or secondary) then Local MS command
on the subring port is cleared else recovery of connectivity between the
interconnection nodes is ignored.

This object is effective only when ring node is interconnection node.

The default value is disabled (0).

This object is applicable only when the compatible version is 2.

Context

MIB: SUPERMICRO-ERPS-MIB
OID: .1.3.6.1.4.1.10876.101.2.40.2.3.1.12
Type: column
Access: readwrite
Status: current
Parent: fsErpsRingConfigEntry
Table: fsErpsRingConfigTable
Siblings: 16

Syntax

Enumeration

Values & Constraints

Enumerated Values

`0`	disabled
`1`	primary
`2`	secondary

Related Objects

Sibling Objects

Object	Type	Syntax	OID
fsErpsRingConfigHoldOffTime This object is used to configure the period for the hold-off timer of this ring. Hold-Off timer will be started when a new defect (SF) is received for this ring…	column	milliseconds Unsigned32	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.1`
fsErpsRingConfigClear The purpose of this object is described below : a) Clearing the forced switch in the ring. b) Clearing the manual switch in the ring. c) Trigger reversion before the WTR or WTB t…	column	Enumeration	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.10`
fsErpsRingConfigInterConnNode This object is configured in interconnection node of the sub-ring to support the feature 'Minimizing segmentation in interconnected rings' as per Appendix X of ITU-T G.8032/Y.1344…	column	Enumeration	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.11`
fsErpsRingConfigIsPort1Present This object identifies the presence of port1 of the ring in the line card. This object should be configured as 'remote' only if the ports are distributed across two…	column	Enumeration	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.13`
fsErpsRingConfigIsPort2Present This object identifies the presence of port2 of the ring in the line card. This object should be configured as 'remote' only if the ports are distributed across two…	column	Enumeration	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.14`
fsErpsRingConfigInfoDistributingPort This object is used in Distributed ERPS to synchronize the ring information between local and remote line cards. The MEP's installed on this distributing port will …	column	IF-MIBInterfaceIndexOrZero	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.15`
fsErpsRingConfigKValue This object is used to configure with integer value which is used for running the timer interval of periodic multiplied by this value to raise a TFOP defect when un related pack…	column	OctetString	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.16`
fsErpsRingConfigFailureOfProtocol This object is used to enable or disable the Failure Of Protocol feature. The value 'true (1)' indicates that TFOP feature is enabled to raise the TRAP when 1. Valid Three RAPS …	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.17`
fsErpsRingConfigGuardTime This object is used to configure the period for the guard timer of this ring. This timer is required to prevent reception of outdated R-APS messages. Guard timer…	column	milliseconds Unsigned32	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.2`
fsErpsRingConfigWTRTime This object is used to configure the period for the Wait to restore timer. This object is applicable, only if this ring is operating in the revertive mode of opera…	column	milliseconds Unsigned32	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.3`
fsErpsRingConfigPeriodicTime This object is used to configure the periodic timer. Periodic timer is used to configure the transmission interval of R-APS PDUs. Periodic timer is not valid for the first 3 R-AP…	column	milliseconds Unsigned32	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.4`
fsErpsRingConfigSwitchPort This object identifies the port that will be blocked by enforcing Forced or Manual Switching command. Port configured here should be one among the fsErpsRingPort1 or fsErpsRingP…	column	IF-MIBInterfaceIndexOrZero	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.5`
fsErpsRingConfigSwitchCmd Before configuring this object with (forceSwitch) or (manualSwitch), fsErpsRingConfigSwitchPort must be configured. When ForcedSwitch is enabled on a ring, irrespe…	column	Enumeration	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.6`
fsErpsRingConfigRecoveryMethod This object is valid, only when the operating mode for the ring is nonRevertive. This object will not have any impact when the ring is operating in revertive mode. …	column	Enumeration	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.7`
fsErpsRingConfigPropagateTC This object is used to enable/disable the propagation of TC in the associated rings, whenever the flush FDB is triggered for this sub-ring. This configuration is applicable only i…	column	Enumeration	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.8`
fsErpsRingConfigWTBTime This object is used to configure the period for Wait to Block timer. This object is effective, only when Force switch or Manual switch is configured in the ring…	column	milliseconds Unsigned32	`.1.3.6.1.4.1.10876.101.2.40.2.3.1.9`