fsErpsRingConfigGuardTime
SUPERMICRO-ERPS-MIB ·
.1.3.6.1.4.1.10876.101.2.40.2.3.1.2
Object
column
r/w
milliseconds Unsigned32
This object is used to configure the period for the guard timer of this
ring. This timer is required to prevent reception of outdated R-APS
messages.
Guard timer will be started on reception of local clear SF event.
R-APS messages (except R-APS event messages) received during the running
of the guard timer will be discarded.
The configured value of this timer is applicable only from the next
start/re-start of the timer.
The guard timer has a period from 0 to 1 hour, configurable in units of
1 millisecond. For example, to configure GuardTime as 1 second,
configure the value as 1000.
Context
- MIB
- SUPERMICRO-ERPS-MIB
- OID
.1.3.6.1.4.1.10876.101.2.40.2.3.1.2- Type
- column
- Access
- readwrite
- Status
- current
- Units
- milliseconds
- Parent
- fsErpsRingConfigEntry
- Table
- fsErpsRingConfigTable
- Siblings
- 16
Syntax
milliseconds Unsigned32
Values & Constraints
Object Constraints
range: 0-3600000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fsErpsRingConfigHoldOffTime This object is used to configure the period for the hold-off timer
of this ring.
Hold-Off timer will be started when a new defect (SF) is received for
this ring… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.10876.101.2.40.2.3.1.1 |
| fsErpsRingConfigClear The purpose of this object is described below :
a) Clearing the forced switch in the ring.
b) Clearing the manual switch in the ring.
c) Trigger reversion before the WTR or WTB t… | column | Enumeration | .1.3.6.1.4.1.10876.101.2.40.2.3.1.10 |
| fsErpsRingConfigInterConnNode This object is configured in interconnection node of the sub-ring to
support the feature 'Minimizing segmentation in interconnected rings'
as per Appendix X of ITU-T G.8032/Y.1344… | column | Enumeration | .1.3.6.1.4.1.10876.101.2.40.2.3.1.11 |
| fsErpsRingConfigMultipleFailure This object is configured in interconnection node of the sub-ring to
support the feature 'Minimizing segmentation in interconnected rings'
as per Appendix X of ITU-T G.8032/Y.1344… | column | Enumeration | .1.3.6.1.4.1.10876.101.2.40.2.3.1.12 |
| fsErpsRingConfigIsPort1Present This object identifies the presence of port1 of the ring in the line
card.
This object should be configured as 'remote' only if the ports are
distributed across two… | column | Enumeration | .1.3.6.1.4.1.10876.101.2.40.2.3.1.13 |
| fsErpsRingConfigIsPort2Present This object identifies the presence of port2 of the ring in the line
card.
This object should be configured as 'remote' only if the ports are
distributed across two… | column | Enumeration | .1.3.6.1.4.1.10876.101.2.40.2.3.1.14 |
| fsErpsRingConfigInfoDistributingPort This object is used in Distributed ERPS to synchronize
the ring information between local and remote line cards.
The MEP's installed on this distributing port will … | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.10876.101.2.40.2.3.1.15 |
| fsErpsRingConfigKValue This object is used to configure with integer value which is used
for running the timer interval of periodic multiplied by this
value to raise a TFOP defect when un related pack… | column | OctetString | .1.3.6.1.4.1.10876.101.2.40.2.3.1.16 |
| fsErpsRingConfigFailureOfProtocol This object is used to enable or disable the Failure Of
Protocol feature. The value 'true (1)' indicates that
TFOP feature is enabled to raise the TRAP when
1. Valid Three RAPS … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.10876.101.2.40.2.3.1.17 |
| fsErpsRingConfigWTRTime This object is used to configure the period for the Wait to restore
timer.
This object is applicable, only if this ring is operating in the
revertive mode of opera… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.10876.101.2.40.2.3.1.3 |
| fsErpsRingConfigPeriodicTime This object is used to configure the periodic timer. Periodic timer
is used to configure the transmission interval of R-APS PDUs. Periodic
timer is not valid for the first 3 R-AP… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.10876.101.2.40.2.3.1.4 |
| fsErpsRingConfigSwitchPort This object identifies the port that will be blocked by enforcing
Forced or Manual Switching command. Port configured here should be one
among the fsErpsRingPort1 or fsErpsRingP… | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.10876.101.2.40.2.3.1.5 |
| fsErpsRingConfigSwitchCmd Before configuring this object with (forceSwitch) or (manualSwitch),
fsErpsRingConfigSwitchPort must be configured.
When ForcedSwitch is enabled on a ring, irrespe… | column | Enumeration | .1.3.6.1.4.1.10876.101.2.40.2.3.1.6 |
| fsErpsRingConfigRecoveryMethod This object is valid, only when the operating mode for the ring is
nonRevertive. This object will not have any impact when the ring is
operating in revertive mode.
… | column | Enumeration | .1.3.6.1.4.1.10876.101.2.40.2.3.1.7 |
| fsErpsRingConfigPropagateTC This object is used to enable/disable the propagation of TC in the
associated rings, whenever the flush FDB is triggered for this sub-ring.
This configuration is applicable only i… | column | Enumeration | .1.3.6.1.4.1.10876.101.2.40.2.3.1.8 |
| fsErpsRingConfigWTBTime This object is used to configure the period for Wait to Block
timer.
This object is effective, only when Force switch or Manual switch is configured
in the ring… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.10876.101.2.40.2.3.1.9 |