slSonetTransceiverType
SL-SONET-MIB ·
.1.3.6.1.4.1.4515.1.6.1.1.1.18
Object
column
Enumeration
The tranceiver type.
Context
- MIB
- SL-SONET-MIB
- OID
.1.3.6.1.4.1.4515.1.6.1.1.1.18- Type
- column
- Access
- readonly
- Status
- current
- Parent
- slSonetConfigEntry
- Table
- slSonetConfigTable
- Siblings
- 17
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | none |
2 | shortWave |
3 | longWave |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| slSonetConfigFrameScramble This object is used to disable or enable the Scrambling
option in SONET line. Please refer to GR-253-CORE for
frame scrambling. | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.1 |
| slSonetOverheadTunneling The section and line overhead tunneling configuration:
none(0) - no tunneling support
lineDcc(1) - line DCC tunneling
k1k2(2) - line DCC + protection k byte
full(3) -… | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.10 |
| slSonetLopBitmask The LOP status. Each bit of the bits represent the status
of the LOP alarm in corresponding STS.
For a path with more than a single STS, only the value of the
first STS in the pat… | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.4515.1.6.1.1.1.11 |
| slSonetTdmTrunk This object is applicable only to the OC-n ports.
TRUE - means that the OC-n port is used as a TDM Trunk.
FLASE - means normal OC-n port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4515.1.6.1.1.1.12 |
| slSonetFsApply Writing to this object activate the slSonetFsTable setting.
This allow the NMS to do many changes to the slSonetFsTable
and then APPLY them at once. This prevent from going throug… | column | Integer32 | .1.3.6.1.4.1.4515.1.6.1.1.1.13 |
| slSonetTxLte The SS bits to transmit (bits 5,6 in H1,H1*). | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.14 |
| slSonetReceivedLte The detected LTE type, according to the received SS bits
(bits 5,6 in H1,H1*). | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.15 |
| slSonetResetPmThreshold Setting this variable to 1 will reset the PM threshold
parameters to the factory defaults. | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.16 |
| slSonetResetAlsParams Setting this variable to 1 will reset the ALS
parameters to the factory defaults. | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.17 |
| slSonetTransceiverMedia The tranceiver media. | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.19 |
| slSonetConfigType This object represents the configured line type for Trunks:
sonetSts48c(5) - 1 x Sts48 (2.5GbTrunk)
sonetSts192c(12) - 1 x Sts192 (10Gb Trunk)
sonetStsOther(13) - for OC-n … | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.2 |
| slSonetConfigDccSelection This object selects the DCC type. | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.3 |
| slSonetResetAllCounters Setting this variable to 1 will cause all of the counters
(performance regsters) on this SONET interface to be initialized
to zero (0). | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.4 |
| slSonetPortThresholdTrapEnable This variable indicates whether threshold traps
should be generated for this SONET interface. | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.5 |
| slSonetConfigSdThreshold This object contains the Bit Error Rate threshold for
Signal Degrade detection on the working line. Once this
threshold is exceeded, an APS switch will occur.
This value is 10 to … | column | Integer32 | .1.3.6.1.4.1.4515.1.6.1.1.1.6 |
| slSonetConfigSfThreshold This object contains the Bit Error Rate threshold for
Signal Fault detection on the working line. Once this
threshold is exceeded, an APS switch will occur.
This value is 10 to th… | column | Integer32 | .1.3.6.1.4.1.4515.1.6.1.1.1.7 |
| slSonetCompression This object applies only for trunk ports.
It specifies if the packets should be compressed.
0 - Means no POS compression,
1 - Means POS compression with CRC-32.
2 - Means POS com… | column | Enumeration | .1.3.6.1.4.1.4515.1.6.1.1.1.9 |