slSonetLopBitmask

SL-SONET-MIB · .1.3.6.1.4.1.4515.1.6.1.1.1.11
MIB view Table view

Object

column SNMPv2-SMICounter64 
The LOP status. Each bit of the bits represent the status
of the LOP alarm in corresponding STS.
For a path with more than a single STS, only the value of the
first STS in the path is relevant.
This object is relevant only for the OC-N cards and not
for the Trunk.
In the next future this object will be replaced with
an object of a new table that shall describe the OC-N
frame structure.

Context

MIB
SL-SONET-MIB
OID
.1.3.6.1.4.1.4515.1.6.1.1.1.11
Type
column
Access
readonly
Status
current
Parent
slSonetConfigEntry
Table
slSonetConfigTable
Siblings
17

Syntax

SNMPv2-SMICounter64
Source
SNMPv2-SMICounter64
Base type
Unsigned64

Values & Constraints

Type Constraints
range: 0..18446744073709551615

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
slSonetConfigFrameScramble
This object is used to disable or enable the Scrambling option in SONET line. Please refer to GR-253-CORE for frame scrambling.
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.1
slSonetOverheadTunneling
The section and line overhead tunneling configuration: none(0) - no tunneling support lineDcc(1) - line DCC tunneling k1k2(2) - line DCC + protection k byte full(3) -…
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.10
slSonetTdmTrunk
This object is applicable only to the OC-n ports. TRUE - means that the OC-n port is used as a TDM Trunk. FLASE - means normal OC-n port.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.4515.1.6.1.1.1.12
slSonetFsApply
Writing to this object activate the slSonetFsTable setting. This allow the NMS to do many changes to the slSonetFsTable and then APPLY them at once. This prevent from going throug…
columnInteger32.1.3.6.1.4.1.4515.1.6.1.1.1.13
slSonetTxLte
The SS bits to transmit (bits 5,6 in H1,H1*).
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.14
slSonetReceivedLte
The detected LTE type, according to the received SS bits (bits 5,6 in H1,H1*).
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.15
slSonetResetPmThreshold
Setting this variable to 1 will reset the PM threshold parameters to the factory defaults.
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.16
slSonetResetAlsParams
Setting this variable to 1 will reset the ALS parameters to the factory defaults.
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.17
slSonetTransceiverType
The tranceiver type.
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.18
slSonetTransceiverMedia
The tranceiver media.
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.19
slSonetConfigType
This object represents the configured line type for Trunks: sonetSts48c(5) - 1 x Sts48 (2.5GbTrunk) sonetSts192c(12) - 1 x Sts192 (10Gb Trunk) sonetStsOther(13) - for OC-n …
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.2
slSonetConfigDccSelection
This object selects the DCC type.
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.3
slSonetResetAllCounters
Setting this variable to 1 will cause all of the counters (performance regsters) on this SONET interface to be initialized to zero (0).
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.4
slSonetPortThresholdTrapEnable
This variable indicates whether threshold traps should be generated for this SONET interface.
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.5
slSonetConfigSdThreshold
This object contains the Bit Error Rate threshold for Signal Degrade detection on the working line. Once this threshold is exceeded, an APS switch will occur. This value is 10 to …
columnInteger32.1.3.6.1.4.1.4515.1.6.1.1.1.6
slSonetConfigSfThreshold
This object contains the Bit Error Rate threshold for Signal Fault detection on the working line. Once this threshold is exceeded, an APS switch will occur. This value is 10 to th…
columnInteger32.1.3.6.1.4.1.4515.1.6.1.1.1.7
slSonetCompression
This object applies only for trunk ports. It specifies if the packets should be compressed. 0 - Means no POS compression, 1 - Means POS compression with CRC-32. 2 - Means POS com…
columnEnumeration.1.3.6.1.4.1.4515.1.6.1.1.1.9