slSonetConfigType

SL-SONET-MIB · .1.3.6.1.4.1.4515.1.6.1.1.1.2

Object

column r/w Enumeration

This object represents the configured line type for Trunks:
sonetSts48c(5)    - 1  x Sts48  (2.5GbTrunk)
sonetSts192c(12)  - 1  x Sts192 (10Gb Trunk)
sonetStsOther(13) - for OC-n interfaces see slSonetFsTable.

Context

MIB: SL-SONET-MIB
OID: .1.3.6.1.4.1.4515.1.6.1.1.1.2
Type: column
Access: readwrite
Status: current
Parent: slSonetConfigEntry
Table: slSonetConfigTable
Siblings: 17

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	sonetSts3
`2`	sonetSts3c
`3`	sonetSts12
`4`	sonetSts12c
`5`	sonetSts48c
`6`	sonetSts3cx4
`7`	sonetSts48
`8`	sonetSts3cx16
`9`	sonetSts3x16
`10`	sonetSts12cx4
`11`	sonetSts12x4
`12`	sonetSts192c
`13`	sonetStsOther

Related Objects

Sibling Objects

Object	Type	Syntax	OID
slSonetConfigFrameScramble This object is used to disable or enable the Scrambling option in SONET line. Please refer to GR-253-CORE for frame scrambling.	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.1`
slSonetOverheadTunneling The section and line overhead tunneling configuration: none(0) - no tunneling support lineDcc(1) - line DCC tunneling k1k2(2) - line DCC + protection k byte full(3) -…	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.10`
slSonetLopBitmask The LOP status. Each bit of the bits represent the status of the LOP alarm in corresponding STS. For a path with more than a single STS, only the value of the first STS in the pat…	column	SNMPv2-SMICounter64	`.1.3.6.1.4.1.4515.1.6.1.1.1.11`
slSonetTdmTrunk This object is applicable only to the OC-n ports. TRUE - means that the OC-n port is used as a TDM Trunk. FLASE - means normal OC-n port.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.4515.1.6.1.1.1.12`
slSonetFsApply Writing to this object activate the slSonetFsTable setting. This allow the NMS to do many changes to the slSonetFsTable and then APPLY them at once. This prevent from going throug…	column	Integer32	`.1.3.6.1.4.1.4515.1.6.1.1.1.13`
slSonetTxLte The SS bits to transmit (bits 5,6 in H1,H1*).	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.14`
slSonetReceivedLte The detected LTE type, according to the received SS bits (bits 5,6 in H1,H1*).	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.15`
slSonetResetPmThreshold Setting this variable to 1 will reset the PM threshold parameters to the factory defaults.	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.16`
slSonetResetAlsParams Setting this variable to 1 will reset the ALS parameters to the factory defaults.	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.17`
slSonetTransceiverType The tranceiver type.	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.18`
slSonetTransceiverMedia The tranceiver media.	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.19`
slSonetConfigDccSelection This object selects the DCC type.	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.3`
slSonetResetAllCounters Setting this variable to 1 will cause all of the counters (performance regsters) on this SONET interface to be initialized to zero (0).	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.4`
slSonetPortThresholdTrapEnable This variable indicates whether threshold traps should be generated for this SONET interface.	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.5`
slSonetConfigSdThreshold This object contains the Bit Error Rate threshold for Signal Degrade detection on the working line. Once this threshold is exceeded, an APS switch will occur. This value is 10 to …	column	Integer32	`.1.3.6.1.4.1.4515.1.6.1.1.1.6`
slSonetConfigSfThreshold This object contains the Bit Error Rate threshold for Signal Fault detection on the working line. Once this threshold is exceeded, an APS switch will occur. This value is 10 to th…	column	Integer32	`.1.3.6.1.4.1.4515.1.6.1.1.1.7`
slSonetCompression This object applies only for trunk ports. It specifies if the packets should be compressed. 0 - Means no POS compression, 1 - Means POS compression with CRC-32. 2 - Means POS com…	column	Enumeration	`.1.3.6.1.4.1.4515.1.6.1.1.1.9`