heRFSwitchState

SCTE-HMS-HE-RF-SWITCH-MIB · .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.4

Object

column Enumeration

Reports the state of the RF Switch.  Not all enumerations 
must be supported.  For example, an A-B RF switch may 
support only the pathA and pathB enumerations while a 
cross-bar switch may support cross, bar, bothA or bothB or 
only cross and bar but not pathA and pathB enumerations. 
              
A value pathA(1) indicates that the switch output is being
fed by side A (first input) of the switch.  This enumeration
is intended for use by an A-B switch.
              
A value pathB(2) indicates that the switch output is being
fed by side B (second input) of the switch. This enumeration
is intended for use by an A-B switch.
              
A value cross(3) indicates that the switch outputs are fed as 
follows:
   Side A (first or primary) output is connected to side B 
   (second or alternate) input.
   Side B (second or alternate) output is connected to side A 
   (first or primary) input.
   This enumeration is intended for use by a cross-bar switch.
              
A value bar(4) indicates that the switch outputs are fed as 
follows:
   Side A (first or primary) output is connected to side A 
   (first or primary) input.
   Side B (second or alternate) output is connected to side B 
   (second or alternate) input.
   This enumeration is intended for use by a cross-bar switch.
              
A value bothA(5) indicates that the switch outputs are fed as 
follows:
   Side A (first or primary) output is connected to side A 
   (first or primary) input.
   Side B (second or alternate) output is connected to side A 
   (first or primary) input.
   This enumeration is intended for use by a cross-bar switch.
              
A value bothB(6) indicates that the switch outputs are fed as 
follows:
   Side A (first or primary) output is connected to side B 
   (second or alternate) input.
   Side B (second or alternate) output is connected to side B 
   (second or alternate) input.
   This enumeration is intended for use by a cross-bar switch.

Context

MIB: SCTE-HMS-HE-RF-SWITCH-MIB
OID: .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.4
Type: column
Access: readonly
Status: current
Parent: heRFSwitchUnitEntry
Table: heRFSwitchUnitTable
Siblings: 8

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	enabled
`2`	disabled
`3`	autonego
`4`	unknown

Related Objects

Sibling Objects

Object	Type	Syntax	OID
heRFSwitchMode This controls and/or reports the switching mode. If automatic(1), the RF switch will evaluate the RF input status and make the decision to affect the switch state. If set to …	column	Enumeration	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.1`
heRFSwitchControl Sets the intended state of the RF Switch. The effect of this control will depend on the value of heRFSwitchMode. If heRFSwitchMode is set to automatic, the value this control is…	column	Enumeration	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.2`
heRFSwitchRevertEnable This controls the use of revert switching. If set to on, the switch will attempt to go back to the preferred settings indicated by heRFSwitchControl if heRFSwit…	column	SCTE-HMS-HEADENDIDENT-MIBHeOnOffControl	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.3`
heRFSwitchFailoverStatus The integral status of both inputs. A value is fault(2), if current switch state heRFSwitchState is different than the preferred setting heRFSwitchControl, o…	column	SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.5`
heRFSwitchBothInputStatus The integral status of both inputs. A value is fault(2), if both input levels are below the nominal value; otherwise, it is normal(1). This object m…	column	SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.6`
heRFSwitchHysteresis Controls switch input hysteresis amount. The amount of hysteresis used and the ability to change it is to be determined by the vendor.	column	0.1 dB Integer32	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.7`
heRFSwitchWaitToRestoreTime Controls hysteresis time in sec. If in automatic switching mode and revert mode is enabled, a switch back to the original side will be delayed for the time sp…	column	1 sec SNMPv2-SMIInteger32	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.8`
heRFSwitchSensorMode Controls what source will be used for determining input status: A value of internal(1) causes the internal RF detection circuitry to be used. A value of external(2) will u…	column	Enumeration	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.9`