heRFSwitchMode

Object

column r/w Enumeration

This controls and/or reports the switching mode.  If 
automatic(1), the RF switch will evaluate the RF 
input status and make the decision to affect the switch state.  
If set to manual(2), the RF switch will not affect the 
switch state itself.

Context

MIB: SCTE-HMS-HE-RF-SWITCH-MIB
OID: .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.1
Type: column
Access: readwrite
Status: current
Parent: heRFSwitchUnitEntry
Table: heRFSwitchUnitTable
Siblings: 8

Related Objects

Sibling Objects

Object	Type	Syntax	OID
heRFSwitchControl Sets the intended state of the RF Switch. The effect of this control will depend on the value of heRFSwitchMode. If heRFSwitchMode is set to automatic, the value this control is…	column	Enumeration	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.2`
heRFSwitchRevertEnable This controls the use of revert switching. If set to on, the switch will attempt to go back to the preferred settings indicated by heRFSwitchControl if heRFSwit…	column	SCTE-HMS-HEADENDIDENT-MIBHeOnOffControl	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.3`
heRFSwitchState Reports the state of the RF Switch. Not all enumerations must be supported. For example, an A-B RF switch may support only the pathA and pathB enumerations while a cross-bar …	column	Enumeration	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.4`
heRFSwitchFailoverStatus The integral status of both inputs. A value is fault(2), if current switch state heRFSwitchState is different than the preferred setting heRFSwitchControl, o…	column	SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.5`
heRFSwitchBothInputStatus The integral status of both inputs. A value is fault(2), if both input levels are below the nominal value; otherwise, it is normal(1). This object m…	column	SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.6`
heRFSwitchHysteresis Controls switch input hysteresis amount. The amount of hysteresis used and the ability to change it is to be determined by the vendor.	column	0.1 dB Integer32	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.7`
heRFSwitchWaitToRestoreTime Controls hysteresis time in sec. If in automatic switching mode and revert mode is enabled, a switch back to the original side will be delayed for the time sp…	column	1 sec SNMPv2-SMIInteger32	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.8`
heRFSwitchSensorMode Controls what source will be used for determining input status: A value of internal(1) causes the internal RF detection circuitry to be used. A value of external(2) will u…	column	Enumeration	`.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.9`

Indexes

Object

Context

Syntax

Values & Constraints

Related Objects