heRFSwitchSensorMode
SCTE-HMS-HE-RF-SWITCH-MIB ·
.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.9
Object
column
r/w
Enumeration
Controls what source will be used for determining input status: A value of internal(1) causes the internal RF detection circuitry to be used. A value of external(2) will use heRFSwitchInputExternalControl to determine input status.
Context
- MIB
- SCTE-HMS-HE-RF-SWITCH-MIB
- OID
.1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- heRFSwitchUnitEntry
- Table
- heRFSwitchUnitTable
- Siblings
- 8
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | full |
2 | half |
3 | unknown |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| heRFSwitchMode This controls and/or reports the switching mode. If
automatic(1), the RF switch will evaluate the RF
input status and make the decision to affect the switch state.
If set to … | column | Enumeration | .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.1 |
| heRFSwitchControl Sets the intended state of the RF Switch. The effect
of this control will depend on the value of heRFSwitchMode.
If heRFSwitchMode is set to automatic, the value this
control is… | column | Enumeration | .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.2 |
| heRFSwitchRevertEnable This controls the use of revert switching.
If set to on, the switch will attempt to go back to the
preferred settings indicated by heRFSwitchControl if
heRFSwit… | column | SCTE-HMS-HEADENDIDENT-MIBHeOnOffControl | .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.3 |
| heRFSwitchState Reports the state of the RF Switch. Not all enumerations
must be supported. For example, an A-B RF switch may
support only the pathA and pathB enumerations while a
cross-bar … | column | Enumeration | .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.4 |
| heRFSwitchFailoverStatus The integral status of both inputs.
A value is fault(2), if current switch state heRFSwitchState
is different than the preferred setting heRFSwitchControl,
o… | column | SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus | .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.5 |
| heRFSwitchBothInputStatus The integral status of both inputs.
A value is fault(2), if both input levels are below
the nominal value; otherwise, it is normal(1).
This object m… | column | SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus | .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.6 |
| heRFSwitchHysteresis Controls switch input hysteresis amount. The amount of hysteresis
used and the ability to change it is to be determined by
the vendor. | column | 0.1 dB Integer32 | .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.7 |
| heRFSwitchWaitToRestoreTime Controls hysteresis time in sec.
If in automatic switching mode and revert mode is enabled,
a switch back to the original side will be delayed for
the time sp… | column | 1 sec SNMPv2-SMIInteger32 | .1.3.6.1.4.1.5591.1.11.4.2.1.1.1.1.8 |