an80iMaxTxPower

REDLINE-AN80I-MIB · .1.3.6.1.4.1.10728.2.1.3.1.2.6

MIB view Table view

Object

scalar r/w Integer32

The Tx Power of the AN-80i. Specifies the power level of the 
system, which is preset at the factory  and should not be altered.  
In the event that this parameter needs to be changed, please contact 
the Redline support team.

Context

MIB: REDLINE-AN80I-MIB
OID: .1.3.6.1.4.1.10728.2.1.3.1.2.6
Type: scalar
Access: readwrite
Status: current
Parent: redlineAn80iWirelesObjects
Siblings: 13

Syntax

Integer32

Values & Constraints

Object Constraints

range: -20-20

Related Objects

Sibling Objects

Object	Type	Syntax	OID
an80iAntennaAllignmentMode Specifies if the antenna alignment buzzer is enabled or not. In the future, new alignment methods may be added.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.1`
an80iAntennaGain The gain of the antenna attached to the system.	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.10`
an80iActiveRFLinks The actual number of provisioned links.	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.11`
an80iAtpControl Enable/disable the automatic Tx power control.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.12`
an80iTurboModeControl Enable/disable the turbo mode. In this mode the system uses a 40MHz channel (20 MHz in normal mode).	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.13`
an80iChannelWidth The width of the channel.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.14`
an80iCurrTxPower The actual Tx Power of the AN-80i Node.	scalar	Integer32	`.1.3.6.1.4.1.10728.2.1.3.1.2.2`
an80iChannelAutoScan Specifies if the frequency auto-scanning feature is enabled	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.3`
an80iCurrFrequency The central frequency on which the equipment operates. If the auto-scanning feature is enabled then this may be different than the an80iOPeratingFrequency. [KHz]	scalar	KHz SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.4`
an80iOPeratingFrequency Specifies the operating frequency of the system [KHz].	scalar	KHz SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.5`
an80iSystemMode 1 = PMP Slave, 2 = PTP Master, 3 = PMP Slave, 4 = PMP Master	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.7`
an80iRFStatusCode Specifies the Error Code for the RF Interface.	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.8`
an80iDFSAction Action taken when a radar is detected on the same frequency.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.9`