an80iCurrFrequency

REDLINE-AN80I-MIB · .1.3.6.1.4.1.10728.2.1.3.1.2.4

MIB view Table view

Object

scalar KHz SNMPv2-SMIInteger32

The central frequency on which the equipment 
operates. If the auto-scanning feature is 
enabled then this may be different than the 
an80iOPeratingFrequency. [KHz]

Context

MIB: REDLINE-AN80I-MIB
OID: .1.3.6.1.4.1.10728.2.1.3.1.2.4
Type: scalar
Access: readonly
Status: current
Units: KHz
Parent: redlineAn80iWirelesObjects
Siblings: 13

Syntax

KHz SNMPv2-SMIInteger32

Source: SNMPv2-SMIInteger32
Base type: Integer32

Values & Constraints

Type Constraints

range: -2147483648..2147483647

Related Objects

Sibling Objects

Object	Type	Syntax	OID
an80iAntennaAllignmentMode Specifies if the antenna alignment buzzer is enabled or not. In the future, new alignment methods may be added.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.1`
an80iAntennaGain The gain of the antenna attached to the system.	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.10`
an80iActiveRFLinks The actual number of provisioned links.	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.11`
an80iAtpControl Enable/disable the automatic Tx power control.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.12`
an80iTurboModeControl Enable/disable the turbo mode. In this mode the system uses a 40MHz channel (20 MHz in normal mode).	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.13`
an80iChannelWidth The width of the channel.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.14`
an80iCurrTxPower The actual Tx Power of the AN-80i Node.	scalar	Integer32	`.1.3.6.1.4.1.10728.2.1.3.1.2.2`
an80iChannelAutoScan Specifies if the frequency auto-scanning feature is enabled	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.3`
an80iOPeratingFrequency Specifies the operating frequency of the system [KHz].	scalar	KHz SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.5`
an80iMaxTxPower The Tx Power of the AN-80i. Specifies the power level of the system, which is preset at the factory and should not be altered. In the event that this parameter needs to be cha…	scalar	Integer32	`.1.3.6.1.4.1.10728.2.1.3.1.2.6`
an80iSystemMode 1 = PMP Slave, 2 = PTP Master, 3 = PMP Slave, 4 = PMP Master	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.7`
an80iRFStatusCode Specifies the Error Code for the RF Interface.	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.8`
an80iDFSAction Action taken when a radar is detected on the same frequency.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.9`