an80iAntennaAllignmentMode

REDLINE-AN80I-MIB · .1.3.6.1.4.1.10728.2.1.3.1.2.1

MIB view Table view

Object

scalar r/w Enumeration

Specifies if the antenna alignment buzzer is 
enabled or not. In the future, new alignment 
methods may be added.

Context

MIB: REDLINE-AN80I-MIB
OID: .1.3.6.1.4.1.10728.2.1.3.1.2.1
Type: scalar
Access: readwrite
Status: current
Parent: redlineAn80iWirelesObjects
Siblings: 13

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	off
`2`	buzzer

Related Objects

Sibling Objects

Object	Type	Syntax	OID
an80iAntennaGain The gain of the antenna attached to the system.	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.10`
an80iActiveRFLinks The actual number of provisioned links.	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.11`
an80iAtpControl Enable/disable the automatic Tx power control.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.12`
an80iTurboModeControl Enable/disable the turbo mode. In this mode the system uses a 40MHz channel (20 MHz in normal mode).	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.13`
an80iChannelWidth The width of the channel.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.14`
an80iCurrTxPower The actual Tx Power of the AN-80i Node.	scalar	Integer32	`.1.3.6.1.4.1.10728.2.1.3.1.2.2`
an80iChannelAutoScan Specifies if the frequency auto-scanning feature is enabled	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.3`
an80iCurrFrequency The central frequency on which the equipment operates. If the auto-scanning feature is enabled then this may be different than the an80iOPeratingFrequency. [KHz]	scalar	KHz SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.4`
an80iOPeratingFrequency Specifies the operating frequency of the system [KHz].	scalar	KHz SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.5`
an80iMaxTxPower The Tx Power of the AN-80i. Specifies the power level of the system, which is preset at the factory and should not be altered. In the event that this parameter needs to be cha…	scalar	Integer32	`.1.3.6.1.4.1.10728.2.1.3.1.2.6`
an80iSystemMode 1 = PMP Slave, 2 = PTP Master, 3 = PMP Slave, 4 = PMP Master	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.7`
an80iRFStatusCode Specifies the Error Code for the RF Interface.	scalar	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.10728.2.1.3.1.2.8`
an80iDFSAction Action taken when a radar is detected on the same frequency.	scalar	Enumeration	`.1.3.6.1.4.1.10728.2.1.3.1.2.9`