an80iChannelAutoScan
REDLINE-AN80I-MIB ·
.1.3.6.1.4.1.10728.2.1.3.1.2.3
Object
scalar
r/w
Enumeration
Specifies if the frequency auto-scanning feature is enabled
Context
- MIB
- REDLINE-AN80I-MIB
- OID
.1.3.6.1.4.1.10728.2.1.3.1.2.3- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- redlineAn80iWirelesObjects
- Siblings
- 13
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | enable |
2 | disable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| an80iAntennaAllignmentMode Specifies if the antenna alignment buzzer is
enabled or not. In the future, new alignment
methods may be added. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.1.3.1.2.1 |
| an80iAntennaGain The gain of the antenna attached to the system. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.10728.2.1.3.1.2.10 |
| an80iActiveRFLinks The actual number of provisioned links. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.10728.2.1.3.1.2.11 |
| an80iAtpControl Enable/disable the automatic Tx power control. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.1.3.1.2.12 |
| an80iTurboModeControl Enable/disable the turbo mode. In this mode the system
uses a 40MHz channel (20 MHz in normal mode). | scalar | Enumeration | .1.3.6.1.4.1.10728.2.1.3.1.2.13 |
| an80iChannelWidth The width of the channel. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.1.3.1.2.14 |
| an80iCurrTxPower The actual Tx Power of the AN-80i Node. | scalar | Integer32 | .1.3.6.1.4.1.10728.2.1.3.1.2.2 |
| an80iCurrFrequency The central frequency on which the equipment
operates. If the auto-scanning feature is
enabled then this may be different than the
an80iOPeratingFrequency. [KHz] | scalar | KHz SNMPv2-SMIInteger32 | .1.3.6.1.4.1.10728.2.1.3.1.2.4 |
| an80iOPeratingFrequency Specifies the operating frequency of the system [KHz]. | scalar | KHz SNMPv2-SMIInteger32 | .1.3.6.1.4.1.10728.2.1.3.1.2.5 |
| an80iMaxTxPower The Tx Power of the AN-80i. Specifies the power level of the
system, which is preset at the factory and should not be altered.
In the event that this parameter needs to be cha… | scalar | Integer32 | .1.3.6.1.4.1.10728.2.1.3.1.2.6 |
| an80iSystemMode 1 = PMP Slave, 2 = PTP Master, 3 = PMP Slave,
4 = PMP Master | scalar | Enumeration | .1.3.6.1.4.1.10728.2.1.3.1.2.7 |
| an80iRFStatusCode Specifies the Error Code for the RF Interface. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.10728.2.1.3.1.2.8 |
| an80iDFSAction Action taken when a radar is detected on the
same frequency. | scalar | Enumeration | .1.3.6.1.4.1.10728.2.1.3.1.2.9 |