rcTlsTestTdcErrorMask

RC-TLS-MIB · .1.3.6.1.4.1.2272.1.52.1.1.1.1.24
MIB view Table view

Object

column Bits 
The error mask associated with the TDC test. Each bit
in the mask represents a specific error. The errors
from least significant bit to highest significant bit
are:
bit  1 - TD nonexistent on destination port
bit  2 - TD disabled on destination port
bit  3 - TD not assigned to destination port
bit  4 - TD filtered on destination NNI port
bit  5 - destination port is NNI
bit  6 - destination port is craft
bit  7 - destination FDB test failed
bit  8 - destination administrative state down
bit  9 - destination operational state down
bit 10 - destination port connectivity mismatch error
bit 11 - destination port type mismatch
bit 12 - destination port mode mismatch error
bit 13 - destination MIB query failed
bit 14 - destination system error
bit 15 - invalid destination port
bit 16 - destination port is CPU
bit 17 - destination port mode mismatch warning
bit 18 - destination port connectivity mismatch warning
bit 19 - default priority used on destination
bit 20 - IP not assigned on destination oel2 port
bit 21 - static entry exists on destination port
bit 22 - destination FDB table full warning
bit 25 - Source Uni Not configured for TDC test.
bit 26 - Source Uni Endpoint Admin State Disable for TDC test.
bit 27 - Source Uni endpoint or TDI not configured for TDC test.
bit 33 - TD nonexistent on source port
bit 34 - TD not assigned to source port
bit 35 - source FDB test failed
bit 36 - source administrative state down
bit 37 - source operational state down
bit 38 - source system error
bit 39 - no response
bit 40 - could not get trace information
bit 41 - could not get time information
bit 42 - source MIB query failed
bit 43 - TD disabled on source port
bit 44 - invalid source port
bit 45 - all ports down on the source node
bit 46 - unknown error
bit 47 - source FDB test failed
bit 48 - static entry exists on source port
bit 49 - no FDB entry for destination MAC, unicast aborted
bit 50 \226 RTT threshold exceeded

Context

MIB
RC-TLS-MIB
OID
.1.3.6.1.4.1.2272.1.52.1.1.1.1.24
Type
column
Access
readonly
Status
current
Parent
rcTlsTestTdcEntry
Table
rcTlsTestTdcTable
Siblings
45

Syntax

Bits

Values & Constraints

Enumerated Values
0unused0
1bit1
2bit2
3bit3
4bit4
5bit5
6bit6
7bit7
8bit8
9bit9
10bit10
11bit11
12bit12
13bit13
14bit14
15bit15
16bit16
17bit17
18bit18
19bit19
20bit20
21bit21
22bit22
23unused23
24unused24
25bit25
26bit26
27bit27
28unused28
29unused29
30unused30
31unused31
32unused32
33bit33
34bit34
35bit35
36bit36
37bit37
38bit38
39bit39
40bit40
41bit41
42bit42
43bit43
44bit44
45bit45
46bit46
47bit47
48bit48
49bit49
50bit50

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
rcTlsTestTdcTestId
The unique TDC test ID for this entry.
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.1
rcTlsTestTdcTestType
Optional target address of the TDC test. For tlsl2 protocol, the options are broadcast and unicast, broadcast only and unicast only. For oel2 protocol, the options are multicast a…
columnEnumeration.1.3.6.1.4.1.2272.1.52.1.1.1.1.10
rcTlsTestTdcTimeTrace
Optional data associated with the TDC test. The basic test validates the provisioning associated with the source ports, destination ports and TDs configured in the test. The time …
columnEnumeration.1.3.6.1.4.1.2272.1.52.1.1.1.1.11
rcTlsTestTdcPriority
Boolean value indicating whether the user specified the packet priority or not.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.52.1.1.1.1.12
rcTlsTestTdcPktsSent
The number of test packets sent.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.13
rcTlsTestTdcPktsReceived
The number of test packets received.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.14
rcTlsTestTdcRttBroadcast
The round-trip-time of the last broadcast test packet in microseconds.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.15
rcTlsTestTdcRttUnicast
The round-trip-time of the last unicast test packet in microseconds.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.16
rcTlsTestTdcPriOpePkt
The OPE network priority. (ie. Customer priority mapped into an OPE priority. Same as tlsTDPriority-Map.)
columnOctetString.1.3.6.1.4.1.2272.1.52.1.1.1.1.17
rcTlsTestTdcTestDate
The local date stamp for the test (DD/MM).
columnOctetString.1.3.6.1.4.1.2272.1.52.1.1.1.1.18
rcTlsTestTdcTestTime
The local time-of-day stamp for the test (HH:MM:SS).
columnOctetString.1.3.6.1.4.1.2272.1.52.1.1.1.1.19
rcTlsTestTdcTDI
The customer TD on which this test is executed.
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.2
rcTlsTestTdcTraceInfo
Boolean value indicating whether the trace info exists for this entry.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.52.1.1.1.1.20
rcTlsTestTdcRowStatus
Used to create/delete an entry in this table
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.2272.1.52.1.1.1.1.21
rcTlsTestTdcAction
This action controls test execution: start will exe-cute the test one time; startPeriodic will begin periodic execution of a test; abort termi-nates the test if it is currently …
columnEnumeration.1.3.6.1.4.1.2272.1.52.1.1.1.1.22
rcTlsTestTdcResult
Result from the last TDC action
columnEnumeration.1.3.6.1.4.1.2272.1.52.1.1.1.1.23
rcTlsTestTdcName
An optional user-defined name for this test. A TDC test name must be unique for each test.
columnOctetString.1.3.6.1.4.1.2272.1.52.1.1.1.1.25
rcTlsTestTdcMulticastCnt
The number of multicast messages sent with each test. A value of zero(0) means the test will look at the FDB for a valid entry, and if one exists a multicast packet will not be se…
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.26
rcTlsTestTdcUnicastCnt
The number of unicast messages sent with each test.
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.27
rcTlsTestTdcRepeatCnt
The number of times a message sequence is executed per test.
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.28
rcTlsTestTdcPeriodicRate
Used to set a periodic test rate. The time is in minutes. The time period ranges from once-a-minute (1) to once-a-day (1440). A time of zero will cause an error indication if a…
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.29
rcTlsTestTdcSrcPortNum
An index value that uniquely identifies the TLS interface (UNI port) at the source of the test.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.3
rcTlsTestTdcPeriodicCount
This object allows the user to place a limit on the number of times a test running periodically shall run. - 0 : Run indefinitely at the periodic rate set via rcTlsTestTdcPeriodi…
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.30
rcTlsTestTdcHistoryCnt
The number of results to be saved for a given TDC test. The maximum number of results which may be saved by a given device is obtainable via rcTlsTestTdcHistoryMax. The total am…
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.31
rcTlsTestTdcRttThreshold
The number of milliseconds allowed for a message to make a round trip journey. Exceeding this threshold can cause the generation of an SNMP rcTlsTestTdcTestFailure event, but will…
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.32
rcTlsTestTdcSnmpTrapControl
Enable or disable the generation of the rcTlsTestTdcTestFailure SNMP trap for this test.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.52.1.1.1.1.33
rcTlsTestTdcRttBroadcastMin
The minimum round-trip-time, in microseconds, required by a broadcast test packet over for all executions of this test.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.34
rcTlsTestTdcRttBroadcastMax
The maximum round-trip-time, in microseconds, required by a broadcast test packet for all executions of this test.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.35
rcTlsTestTdcRttBroadcastAvg
The average round-trip-time for a broadcast test packet in microseconds for all executions of this test.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.36
rcTlsTestTdcRttUnicastMin
The minimum round-trip-time, in microseconds, required by a unicast test packet for all executions of this test.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.37
rcTlsTestTdcRttUnicastMax
The maximum round-trip-time, in microseconds, required by a unicast test packet for all executions of this test.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.38
rcTlsTestTdcRttUnicastAvg
The average round-trip-time for a unicast test packet in microseconds for all executions of this test.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.39
rcTlsTestTdcDstPortNum
An index value that uniquely identifies the destination TLS interface (LAN port).
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.4
rcTlsTestTdcHopCountMin
The minimum hop count for all executions of this test.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.40
rcTlsTestTdcHopCountMax
The maximum hop count for all executions of this test.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.41
rcTlsTestTdcHopCountAvg
The average hop count all executions of this test.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.42
rcTlsTestTdcClearHistoryAction
The clear option removes all stored test results for this test including the most recent test result. The clear option has no affect if there are no stored results. A query of th…
columnEnumeration.1.3.6.1.4.1.2272.1.52.1.1.1.1.43
rcTlsTestTdcScheduled
Indicates whether this test is currently scheduled to execute in periodic mode. A TRUE response indicates the test is scheduled to run at some future time, and will execute as sch…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.52.1.1.1.1.44
rcTlsTestTdcCurrentPeriodicCount
This object returns the current value of the periodic counter. If the value had been set greater than zero and the test is currently running periodically, then this object is dec…
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.45
rcTlsTestTdcQtag
TDC test Qtag, it is 0 by default. It means the first Qtag of the Tls Endpoint
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.46
rcTlsTestTdcSrcPortIP
The IP address of the source port or CPU.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.2272.1.52.1.1.1.1.5
rcTlsTestTdcDstPortIP
The IP address of the destination port or CPU.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.2272.1.52.1.1.1.1.6
rcTlsTestTdcPktPriority
Optional 802.1 network priority to be used for this test. If not specified by the user, the port default priority is assumed.
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.7
rcTlsTestTdcPktTimeout
Optional timeout period for the TDC test in seconds. If not specified, a default value of 10 seconds will be used.
columnInteger32.1.3.6.1.4.1.2272.1.52.1.1.1.1.8
rcTlsTestTdcProtocol
The protocol to use for the TDC test. If not specified by the user, the mode (protocol) of the source UNI port will be assumed.
columnEnumeration.1.3.6.1.4.1.2272.1.52.1.1.1.1.9