prtSTestMask

RAD-MIB · .1.3.6.1.4.1.164.3.1.4.1.1.1.9

Object

column SNMPv2-SMIInteger32

This is a mask which indicates which tests from the
'prtSTstCmd' list are allowed for the requested port.
If a specific test is allowed, its respective bit
will be SET in the mask :
              
  TEST                  BIT
 -----------            ---
 local-loop              1
 remote-loop             2
 loc-and-rem-main-loops  3
 remote-analog-loop      4
 remote-digital-loop     5
 rem-loop-on-ext-unit    6
 bert                    7
 tone-injection          8
 dlci local-loop         9
 all dlci local-loop    10
 dlci remote-loop       11
 all dlci remote-loop   12
 bert-and-rem-loop-on-rem-unit 13
 rem-loop-on-rem-unit   14
 block                  15
 backward-tone-inject   16
 llb                    17
 rlb                    18
              
 ft1Enable              21
		lbbd                   22  --for 2B+D
		lb1                    23  --for B1
		lb2                    24  --for B2
		llb-on-rem-unit        25
		bert-on-rem-unit       26
		bert-on-rem-and-llb-on-rem-unit 27
		local-and-bert-on-rem-unit 28
		local-loop-on-rem-unit 29
		localBert              30  --towards IO ports
		test-per-TS            31
              
 e.g : If the return value is 3 -> 0000000000000011  ->
       Bits 1 & 2 are set -> the allowed tests are :
                                    local-loop
                                    remote-loop

Context

MIB: RAD-MIB
OID: .1.3.6.1.4.1.164.3.1.4.1.1.1.9
Type: column
Access: readonly
Status: current
Parent: prtSInstEntry
Table: prtSInstTable
Siblings: 16

Syntax

SNMPv2-SMIInteger32

Source: SNMPv2-SMIInteger32
Base type: Integer32

Values & Constraints

Type Constraints

range: -2147483648..2147483647

Related Objects

Sibling Objects

Object	Type	Syntax	OID
prtSInstSltIdx This attribute indicates a unique number to identify the slot where the card is inserted. In the ?004 Unit the entries io6(10)..io(16) are not valid. For the Vmux2100 Main Board c…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.4.1.1.1.1`
prtSTstCmd Setting this attribute to any of the above values will initiate a test on the specific port if the operation is legal. If the operation is not legal, the mux will ignore the opera…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.4.1.1.1.10`
prtSTstDuration This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to all the test operations. The resolution will be a minute, and the max…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.4.1.1.1.11`
prtSBertClrCmd Setting this attribute initiates bert count clear operation. It is valid only when bert test is active on the specific port.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.4.1.1.1.12`
prtSBertTstRslt This attribute indicates the number of Bit Error Rate indicated during the BERT operation. It is valid only when bert test is active on the specific port.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.4.1.1.1.13`
prtSInterfaceType This attribute indicates a unique HW interface type of the selected port.	column	OctetString	`.1.3.6.1.4.1.164.3.1.4.1.1.1.14`
prtSParamStatus This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex …	column	OctetString	`.1.3.6.1.4.1.164.3.1.4.1.1.1.15`
prtSTestMaskXp This is an Expanded test mask of the prtSTestMask object. The prtSTestMask object reached its maximum, being an Integer with 32 bits. This object indicates which tests from the '…	column	OctetString	`.1.3.6.1.4.1.164.3.1.4.1.1.1.16`
prtSRdnStatus Redundancy Status of this port. noRdn - this port is not part of a Redundancy pair/group. offline - this port is offline from Redundancy point of view. online - this port is onli…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.4.1.1.1.17`
prtSInstPrtIdx This attribute indicates a unique number to identify a port in a specific card. The valid ports depend on the installed card: the valid external ports (interfaces) are (1..mdlCNoO…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.4.1.1.1.2`
prtSInstPrtType This attribute describes the type of the designated port. In MX 3000 only external & internal options are used. All the other options are only for MX 30/300 which need special han…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.4.1.1.1.3`
prtSInstIfIndex This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifind…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.4.1.1.1.4`
prtSActiveStatus This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the ch is not connected according …	column	Enumeration	`.1.3.6.1.4.1.164.3.1.4.1.1.1.5`
prtSAlrStatus Indicates the alarm state in the port(ch) agent level. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, …	column	Enumeration	`.1.3.6.1.4.1.164.3.1.4.1.1.1.6`
prtSMaskedAlrStat Indicates the alarm state in the port(ch) agent level, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) …	column	Enumeration	`.1.3.6.1.4.1.164.3.1.4.1.1.1.7`
prtSClearAlrCmd Setting this attribute to on(3) enforces a clear operation of the alarm status events in the given port. The clear operation will not be applied for masked/inverted alarms.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.4.1.1.1.8`