prtSInstIfIndex
RAD-MIB ·
.1.3.6.1.4.1.164.3.1.4.1.1.1.4
Object
column
SNMPv2-SMIInteger32
This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx the value will be '7fffffff'h.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.3.1.4.1.1.1.4- Type
- column
- Access
- readonly
- Status
- current
- Parent
- prtSInstEntry
- Table
- prtSInstTable
- Siblings
- 16
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| prtSInstSltIdx This attribute indicates a unique number to identify the
slot where the card is inserted.
In the ?004 Unit the entries io6(10)..io(16) are not valid.
For the Vmux2100 Main Board c… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.1 |
| prtSTstCmd Setting this attribute to any of the above values will
initiate a test on the specific port if the operation is
legal. If the operation is not legal, the mux will ignore
the opera… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.10 |
| prtSTstDuration This attribute indicates the maximum duration of executing
a test on the specific port. This entry applies to all the
test operations. The resolution will be a minute, and the
max… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.4.1.1.1.11 |
| prtSBertClrCmd Setting this attribute initiates bert count clear operation.
It is valid only when bert test is active on the specific
port. | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.12 |
| prtSBertTstRslt This attribute indicates the number of Bit Error Rate
indicated during the BERT operation.
It is valid only when bert test is active on the specific
port. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.4.1.1.1.13 |
| prtSInterfaceType This attribute indicates a unique HW interface type of the
selected port. | column | OctetString | .1.3.6.1.4.1.164.3.1.4.1.1.1.14 |
| prtSParamStatus This object indicates Status of parameters specific to the
selected port.
- For a port that has no special status or is supported
by prtSExHsfStatTable - 1 Octet: 00hex
… | column | OctetString | .1.3.6.1.4.1.164.3.1.4.1.1.1.15 |
| prtSTestMaskXp This is an Expanded test mask of the prtSTestMask object.
The prtSTestMask object reached its maximum, being an Integer with 32 bits.
This object indicates which tests from the '… | column | OctetString | .1.3.6.1.4.1.164.3.1.4.1.1.1.16 |
| prtSRdnStatus Redundancy Status of this port.
noRdn - this port is not part of a Redundancy pair/group.
offline - this port is offline from Redundancy point of view.
online - this port is onli… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.17 |
| prtSInstPrtIdx This attribute indicates a unique number to identify a port
in a specific card.
The valid ports depend on the installed card:
the valid external ports (interfaces) are (1..mdlCNoO… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.4.1.1.1.2 |
| prtSInstPrtType This attribute describes the type of the designated port.
In MX 3000 only external & internal options are used.
All the other options are only for MX 30/300 which need special han… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.3 |
| prtSActiveStatus This attribute describes the activity status of the port.
unknown(1) indicates that the information is not supported.
notUsed(2) indicates that the ch is not connected according
… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.5 |
| prtSAlrStatus Indicates the alarm state in the port(ch) agent level.
This attribute will be set to:
critical(7) - when there is at least one active (state ON)
critical alarm,
… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.6 |
| prtSMaskedAlrStat Indicates the alarm state in the port(ch) agent level,
including Masked alarms.
This attribute will be set to:
critical(7) - when there is at least one active (state ON)
… | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.7 |
| prtSClearAlrCmd Setting this attribute to on(3) enforces a clear operation
of the alarm status events in the given port. The clear
operation will not be applied for masked/inverted alarms. | column | Enumeration | .1.3.6.1.4.1.164.3.1.4.1.1.1.8 |
| prtSTestMask This is a mask which indicates which tests from the
'prtSTstCmd' list are allowed for the requested port.
If a specific test is allowed, its respective bit
will be SET in the mask… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.4.1.1.1.9 |