optSelectLink

RAD-MIB · .1.3.6.1.4.1.164.3.5.1.1.7

Object

column r/w Enumeration

This object is used by Optimuxes.
- For Optimux 4E1/T1 Old Look: 
  This MIB object enables the user to force the device to use specific link.
autoredundancy= Main (Link 1) is the default link. When it will fail, the 
             device will use Backup (Link 2). If Main recovers, it 
             automatically returns to Main.
autoWoReturn  = Automatic Without Return. Main (Link 1) is the default link. 
             When it will fail, the device will use Backup (Link 2). 
             If Main recovers, it will NOT return to Main. It will 
                  continue using Backup.
			        This option is supported only by LRS cards.
  main         =  Forces the device to start immediately use of Main (Link 1),
                  no matter what is its state and stay there. No Redundancy.
  back         =  Forces the device to start immediately use of Backup (Link 2),
                  no matter what is its state and stay there. No Redundancy.
- For Optimux-T3, Optimux-155, Optimux-XL and OP-4 (New Look):
  This MIB object is used to select which Link will be used as MAIN.
	Therefore:
  autoredundancy - not supported 
  main = Link A is MAIN (=default).
  back = Link B is MAIN.

Context

MIB: RAD-MIB
OID: .1.3.6.1.4.1.164.3.5.1.1.7
Type: column
Access: readwrite
Status: current
Parent: optMxConfigEntry
Table: optMxConfigTable
Siblings: 26

Syntax

Enumeration

Values & Constraints

Enumerated Values

`2`	auto
`3`	manual

Related Objects

Sibling Objects

Object	Type	Syntax	OID
optIndex optIndex = 1 is for local Optimux. optIndex = 2 is for remote Optimux.	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.1`
optRedundancyStatus If there are two modules 'links', then this field should be set to available(2). If there is only one module 'link', this field should be set to notAvailable(3).	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.10`
optRedundancyCnf This object is used by Optimux-XL, FomiE3/T3, Optimux-T3 and Optimux-155. For Optimux-XL: If optRedundancyStatus = notAvailable(3), then this field can be off(2) or forcedBU(6…	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.11`
optFarEndType Far-End type of product. This object is especially relevant for the local optimux. notApplicable - for devices that don't have a far-end unit.	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.12`
optServiceChEnable Service Channel Enable/Disable for each Optimux (local/remote).	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.13`
optMaskChAlr Mask Channel Alarm. This object is applicable only for Optimux cards. The value of this object is a sum of 2**n, where n is a bit assigned to a certain Channel. Bit='1' means ma…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.5.1.1.14`
optAisEnable AIS enable/disable. notApplicable - for devices that do not support this feature.	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.15`
optFarMng This object is used by Optimux-XL and FomiE3/T3. Is there possibility of Far-End Management (no/yes). This object is applicable only for the Local device. notApplicable - for Remo…	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.16`
optClockDivision This object is applicable only for FomiE3/T3 having an HSSI Electrical interface. It gives the possibility of Clock Division, so that Clock Rate will be less than T3/E3. notApplic…	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.17`
optDteLoopEnable DTE Loop enable/disable (for example loop command requested by router). This object is applicable only for products having HSSI interface. notApplicable - for devices that do…	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.18`
optGrpClockSourcePrt This object is applicable for Optimux-T3, when optGrpClockSource=localExternal. It enables the user to select the Channel or Station Clock from which the Clock is received. Valid…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.5.1.1.19`
optHWVersion HW Version of the device.	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.164.3.5.1.1.2`
optIncomingAlarm State of the Incoming Alarm (On/Off), via Alarm Relay connector. This object is applicable only for Optimux-T3.	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.20`
optDefChannelSet Default configuration for all Optimux Channels: T1 or E1. This object is applicable only for Optimux-T3.	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.21`
optWaitToRestore This parameter defines the time (sec) device has to wait in the redundant state until it goes back to the default Link.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.5.1.1.22`
optEnforcedLink This parameter is not applicable when optRedundancyCnf = off. It enables user to enforce a Link in spite of the redundancy mechanism. Selecting the noEnforcement(2) value cause re…	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.23`
optFlipUponEvent This object allows user to define if Flip to the other port will be performed (or not), for certain possible events. Each event is represented by a bit. The value of the object is…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.5.1.1.24`
optHwMaskChAlr Mask Channel Alarm done by the HW dip-switches. This object is applicable only for Optimux cards. The value of this object is a sum of 2**n, where n is a bit assigned to a certai…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.5.1.1.25`
optServiceChExist Service Channel Existence indication for each Optimux (local/remote).	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.26`
optMaskSystemAlr Mask all system alarms for each Optimux (local/remote).	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.27`
optSWVersion SW Version of the device.	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.164.3.5.1.1.3`
optPSPrimary The status of the primary Power Supply Unit.	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.4`
optPSSecondary The status of the secondary Power Supply Unit.	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.5`
optLinkActive This object indicates which link is active. For Optimux-4 it may be: 5, 6 or 105, 106 For FOMi-E3/T3 it may be: 51, 61 or 151, 161. For Optimux-T3 it may be: 51 or 61. For Optimu…	column	IF-MIBInterfaceIndex	`.1.3.6.1.4.1.164.3.5.1.1.6`
optGrpPayLoadLoop Performs payload loop ( remote loop) to 4 E1 channels at once.	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.8`
optGrpClockSource For Optimux XL: If dsx3TransmitClockSource = localTiming(2), then the user can configure this field as: localInternal(2) = use the internal clock of the device localExternal(3) = …	column	Enumeration	`.1.3.6.1.4.1.164.3.5.1.1.9`