modmPrtDteRtsDcdEnable

Related Objects

Sibling Objects

Object	Type	Syntax	OID
modmPrtDteIndex The DTE port index.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.4.4.4.1.1.1`
modmPrtDteAlbEnable Enable/Disable Analog Loop-Back on this modem, externally initiated.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.10`
modmPrtDteDsrDtrEnable Enable/Disable DSR-DTR.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.12`
modmPrtDteSignaling Each bit represents a specific signal state. 1 - means : signal is ON , Enabled, Yes (exists) 0 - means : signal is OFF, Disabled, No . For detailed bit assignment see product's s…	column	OctetString	`.1.3.6.1.4.1.164.3.4.4.4.1.1.13`
modmPrtDteLoops Loops that can be run on the DTE port. none - no loop (stop running loop) ana - Local Analog Line loop rem - Remote Analog Line loop anaAndBert - ana & BERT together re…	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.14`
modmPrtDteTests This is a mask which indicates - for Get: which tests are running on the DTE port. - for Set: tests the user wishes to start or stop. Each test has its specific bit. - '1' means…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.4.4.4.1.1.15`
modmPrtDteClearAllTests Setting this attribute to on, clears all the running loops and tests of the DTE port. Upon completion, the value will automatically change to off(2).	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.16`
modmPrtDteBertResult Result of BERT for the selected DTE port. Applicable only if BERT is running on the DTE port.	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.164.3.4.4.4.1.1.17`
modmPrtDteErrCorrect notApplicable - for modems that do not support this object on - will start a random error correction process. onBurst - will start a burst error correction process. Setti…	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.18`
modmPrtDteV54DigitalTest Enables to start a remote digital loopback upon recognition of a special pattern. disable - will not start a digital loopback when a special pattern is recognized. enable - will…	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.19`
modmPrtDteProtocol The DTE port Protocol.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.2`
modmPrtDteV54DigitalTestStatus Indicates whether a remote digital test was triggered by a pattern by the remote modem or not. no - the digital test wasn't triggered by a pattern by the remote modem. yes - the …	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.20`
modmPrtDteTestTimeOut Indicates the timeout for LLB test. 0=Forever	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.4.4.4.1.1.21`
modmPrtDteAlarmForwarding This MIB object defines whether to enable or disable Alarm Forwarding for this port. It means whether this port will be affected by the failure of its respective Line port.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.22`
modmPrtDteDataBits The DTE number of data bits.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.3`
modmPrtDteStopBits The DTE minimum number of stop bits in the tx async frame.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.4`
modmPrtDteRate The DTE port rate.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.5`
modmPrtDteCtsDelay CTS/RTS delay, in msec. dxx = xx msec. notApplicable - for ASMi-31, ASMi-32.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.6`
modmPrtDteParity This attribute indicates the parity mode in async frame.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.7`
modmPrtDteIfType The interface type of the DTE port.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.8`
modmPrtDteRlbEnable Enable/Disable Remote Loop-Back on this modem, externally initiated.	column	Enumeration	`.1.3.6.1.4.1.164.3.4.4.4.1.1.9`

Object

Context

Syntax

Values & Constraints

Related Objects

`1`	notApplicable
`2`	disable
`3`	enable