modmPrtDteErrCorrect

RAD-MIB · .1.3.6.1.4.1.164.3.4.4.4.1.1.18
MIB view Table view

Object

column r/w Enumeration 
notApplicable - for modems that do not support this object
on      - will start a random error correction process.
	   onBurst - will start a burst error correction process.
Setting this object to 'off', will stop any kind of error correction process.

Context

MIB
RAD-MIB
OID
.1.3.6.1.4.1.164.3.4.4.4.1.1.18
Type
column
Access
readwrite
Status
current
Parent
modmPrtDteEntry
Table
modmPrtDteTable
Siblings
21

Syntax

Enumeration

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
modmPrtDteIndex
The DTE port index.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.164.3.4.4.4.1.1.1
modmPrtDteAlbEnable
Enable/Disable Analog Loop-Back on this modem, externally initiated.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.10
modmPrtDteRtsDcdEnable
Enable/Disable RTS-DCD.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.11
modmPrtDteDsrDtrEnable
Enable/Disable DSR-DTR.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.12
modmPrtDteSignaling
Each bit represents a specific signal state. 1 - means : signal is ON , Enabled, Yes (exists) 0 - means : signal is OFF, Disabled, No . For detailed bit assignment see product's s…
columnOctetString.1.3.6.1.4.1.164.3.4.4.4.1.1.13
modmPrtDteLoops
Loops that can be run on the DTE port. none - no loop (stop running loop) ana - Local Analog Line loop rem - Remote Analog Line loop anaAndBert - ana & BERT together re…
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.14
modmPrtDteTests
This is a mask which indicates - for Get: which tests are running on the DTE port. - for Set: tests the user wishes to start or stop. Each test has its specific bit. - '1' means…
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.164.3.4.4.4.1.1.15
modmPrtDteClearAllTests
Setting this attribute to on, clears all the running loops and tests of the DTE port. Upon completion, the value will automatically change to off(2).
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.16
modmPrtDteBertResult
Result of BERT for the selected DTE port. Applicable only if BERT is running on the DTE port.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.164.3.4.4.4.1.1.17
modmPrtDteV54DigitalTest
Enables to start a remote digital loopback upon recognition of a special pattern. disable - will not start a digital loopback when a special pattern is recognized. enable - will…
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.19
modmPrtDteProtocol
The DTE port Protocol.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.2
modmPrtDteV54DigitalTestStatus
Indicates whether a remote digital test was triggered by a pattern by the remote modem or not. no - the digital test wasn't triggered by a pattern by the remote modem. yes - the …
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.20
modmPrtDteTestTimeOut
Indicates the timeout for LLB test. 0=Forever
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.164.3.4.4.4.1.1.21
modmPrtDteAlarmForwarding
This MIB object defines whether to enable or disable Alarm Forwarding for this port. It means whether this port will be affected by the failure of its respective Line port.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.22
modmPrtDteDataBits
The DTE number of data bits.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.3
modmPrtDteStopBits
The DTE minimum number of stop bits in the tx async frame.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.4
modmPrtDteRate
The DTE port rate.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.5
modmPrtDteCtsDelay
CTS/RTS delay, in msec. dxx = xx msec. notApplicable - for ASMi-31, ASMi-32.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.6
modmPrtDteParity
This attribute indicates the parity mode in async frame.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.7
modmPrtDteIfType
The interface type of the DTE port.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.8
modmPrtDteRlbEnable
Enable/Disable Remote Loop-Back on this modem, externally initiated.
columnEnumeration.1.3.6.1.4.1.164.3.4.4.4.1.1.9