modmPrtDteBertResult
RAD-MIB ·
.1.3.6.1.4.1.164.3.4.4.4.1.1.17
Object
column
SNMPv2-TCDisplayString
Result of BERT for the selected DTE port. Applicable only if BERT is running on the DTE port.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.3.4.4.4.1.1.17- Type
- column
- Access
- readonly
- Status
- current
- Parent
- modmPrtDteEntry
- Table
- modmPrtDteTable
- Siblings
- 21
Values & Constraints
Enumerated Values
1 | notApplicable |
2 | t1 |
3 | e1 |
Type Constraints
range: 0..255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| modmPrtDteIndex The DTE port index. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.4.4.4.1.1.1 |
| modmPrtDteAlbEnable Enable/Disable Analog Loop-Back on this modem, externally
initiated. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.10 |
| modmPrtDteRtsDcdEnable Enable/Disable RTS-DCD. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.11 |
| modmPrtDteDsrDtrEnable Enable/Disable DSR-DTR. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.12 |
| modmPrtDteSignaling Each bit represents a specific signal state.
1 - means : signal is ON , Enabled, Yes (exists)
0 - means : signal is OFF, Disabled, No .
For detailed bit assignment see product's s… | column | OctetString | .1.3.6.1.4.1.164.3.4.4.4.1.1.13 |
| modmPrtDteLoops Loops that can be run on the DTE port.
none - no loop (stop running loop)
ana - Local Analog Line loop
rem - Remote Analog Line loop
anaAndBert - ana & BERT together
re… | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.14 |
| modmPrtDteTests This is a mask which indicates
- for Get: which tests are running on the DTE port.
- for Set: tests the user wishes to start or stop.
Each test has its specific bit.
- '1' means… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.4.4.4.1.1.15 |
| modmPrtDteClearAllTests Setting this attribute to on, clears all the running loops
and tests of the DTE port. Upon completion, the value will
automatically change to off(2). | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.16 |
| modmPrtDteErrCorrect notApplicable - for modems that do not support this object
on - will start a random error correction process.
onBurst - will start a burst error correction process.
Setti… | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.18 |
| modmPrtDteV54DigitalTest Enables to start a remote digital loopback upon recognition of a special pattern.
disable - will not start a digital loopback when a special pattern is
recognized.
enable - will… | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.19 |
| modmPrtDteProtocol The DTE port Protocol. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.2 |
| modmPrtDteV54DigitalTestStatus Indicates whether a remote digital test was triggered by a pattern
by the remote modem or not.
no - the digital test wasn't triggered by a pattern by the remote modem.
yes - the … | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.20 |
| modmPrtDteTestTimeOut Indicates the timeout for LLB test.
0=Forever | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.4.4.4.1.1.21 |
| modmPrtDteAlarmForwarding This MIB object defines whether to enable or disable Alarm Forwarding for this port.
It means whether this port will be affected by the failure of its respective Line port. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.22 |
| modmPrtDteDataBits The DTE number of data bits. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.3 |
| modmPrtDteStopBits The DTE minimum number of stop bits in the tx async frame. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.4 |
| modmPrtDteRate The DTE port rate. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.5 |
| modmPrtDteCtsDelay CTS/RTS delay, in msec.
dxx = xx msec.
notApplicable - for ASMi-31, ASMi-32. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.6 |
| modmPrtDteParity This attribute indicates the parity mode in async frame. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.7 |
| modmPrtDteIfType The interface type of the DTE port. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.8 |
| modmPrtDteRlbEnable Enable/Disable Remote Loop-Back on this modem, externally
initiated. | column | Enumeration | .1.3.6.1.4.1.164.3.4.4.4.1.1.9 |