mdlCDetailedStatus
RAD-Dacs-MIB ·
.1.3.6.1.4.1.164.3.3.2.1.2.1.10
Object
column
Bits
The module current status.
When moduleOperStatus is down(2), but not as a result of
setting the moduleAdminStatus to down(2), this object contains
the failure reason or reasons.
The moduleOperStatus value can be up(1) only when all bits of
this object are cleared.
The following failure reasons can be indicated:
initializing (0)
The module initialization procedure is in progress.
For a MC the start-up time may take a few minutes and the bit
should be set during this time.
cardMismatch (1)
There is a type mismatch between the pre-provisioned module and
the actual installed module.
initFailed (2)
A SW download problem from the Main Card to an I/O card.
provisionFailed (3)
Provisioning failure or any other initialization problem of an I/O card.
selfTestFailed (4)
Power-up or periodic diagnostics has detected a H/W malfunction of the card.
commFailure (5)
The MC detects loss of management communication with an I/O card that
it was previously talking to. In other words, the I/O card completed
its initialization and already established communication with the MC
and at some time later the management communication failed.
bpInterfaceFailure (6)
One or more of the module's backplane interfaces has detected bit errors
or loss of packets.
configurationMismatch(7)
Indication that a configuration mismatch was detected while
the card has been configured
noInputPower(8)
Indication that module (usually a power inlet) is plugged-in but no power
cable is attached to it.
Context
- MIB
- RAD-Dacs-MIB
- OID
.1.3.6.1.4.1.164.3.3.2.1.2.1.10- Type
- column
- Access
- readonly
- Status
- current
- Parent
- mdlCEntry
- Table
- mdlCTable
- Siblings
- 17
Syntax
Bits
Values & Constraints
Enumerated Values
0 | initializing |
1 | cardMismatch |
2 | initFailed |
3 | provisionFailed |
4 | selfTestFailed |
5 | commFailure |
6 | bpInterfaceFailure |
7 | configurationMismatch |
8 | noInputPower |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| mdlCConfigIdx This object indicates the Configuration number (1..255)
referred.
Value of 255 specifies the TmpCnfg (Scratch). | column | Integer32 | .1.3.6.1.4.1.164.3.3.2.1.2.1.1 |
| mdlCEntPhysicalIndex The object contains index of the related entPhysicalEntry of the
ENTITY-MIB, see RFC4133. It points the relevant card and not the
card slot. The agent should build this index acco… | column | ENTITY-MIBPhysicalIndexOrZero | .1.3.6.1.4.1.164.3.3.2.1.2.1.11 |
| mdlCReset Reset action to be performed on the module.
Agent should set mdlCReset to off (2) during initialization. | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.2.1.12 |
| mdlCConfigMismatchReason This object details the card configuration mismatch
in case the object mdlCDetailedStatus is equal to configurationMismatch(7) | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.2.1.13 |
| mdlCIpAddressType The object defines type of the mdlCIpAddress as defined
in the InetAddress MIB: IPv4 or IPv6. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.164.3.3.2.1.2.1.14 |
| mdlCIpAddress The object defines card IP address that will be associated
with the card loopback IP interface. | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.164.3.3.2.1.2.1.15 |
| mdlCHardwareFailureReason | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.2.1.16 |
| mdlCSlotIdx This object indicates a unique number of the slot position
in which the module is inserted.
The Kilomux should use enumerated values starting with kmx. | column | RAD-TCSlotType | .1.3.6.1.4.1.164.3.3.2.1.2.1.2 |
| mdlCFanControl The desired state of the fan.
Module fan control shall manage all fans on the module, if there are more than one.
When mdlCFanControl is 'up', all module's fans mus… | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.2.1.22 |
| mdlCFanOperStatus The current operational state of the module's fans. Provides the
aggregated state of all fans, if there are more than one on the module.
… | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.2.1.23 |
| mdlCProgCardType This object indicates the card type assigned to the specific
slot in the common configuration.
This object is identical for all the configurations (1..255).
Only the TmpCnf(255) … | column | RAD-TCCardType | .1.3.6.1.4.1.164.3.3.2.1.2.1.3 |
| mdlCNoOfExtPrt Number of external ports in the programmed module of
the specific slot position | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.2.1.2.1.4 |
| mdlCNoOfIntPrt Number of internal ports in the programmed module of
the specific slot position. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.2.1.2.1.5 |
| mdlCParam General configuration object at card level (per configuration).
NotApplicable=0, for cards that don't support this object.
For D8U and D16U cards of DXC, the objec… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.2.1.2.1.6 |
| mdlCAdminStatus The desired state of the module.
Module adminStatus should be managed for all modules in the shelf.
When adminStatus is 'down', this module is not operational i.e.
… | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.2.1.7 |
| mdlCActualCardType This object defines actual card type. | column | RAD-TCCardType | .1.3.6.1.4.1.164.3.3.2.1.2.1.8 |
| mdlCOperStatus The current operational state of the module.
up
The physical module agrees with the pre-provisioned card type,
and the configuration of the module succeeded.
… | column | Enumeration | .1.3.6.1.4.1.164.3.3.2.1.2.1.9 |