circuitPoleSensorUnits
PDU2-MIB ·
.1.3.6.1.4.1.13742.6.3.11.6.1.6
Object
column
SensorUnitsEnumeration
The unit in which the sensor reading is reported. This parameter does not apply to sensors without numerical reading.
Context
- MIB
- PDU2-MIB
- OID
.1.3.6.1.4.1.13742.6.3.11.6.1.6- Type
- column
- Access
- readonly
- Status
- current
- Parent
- circuitPoleSensorConfigurationEntry
- Table
- circuitPoleSensorConfigurationTable
- Siblings
- 18
Syntax
SensorUnitsEnumeration
- Source
- SensorUnitsEnumeration
- Base type
Enumeration
Values & Constraints
Type Values
-1 | none |
0 | other |
1 | volt |
2 | amp |
3 | watt |
4 | voltamp |
5 | wattHour |
6 | voltampHour |
7 | degreeC |
8 | hertz |
9 | percent |
10 | meterpersec |
11 | pascal |
12 | psi |
13 | g |
14 | degreeF |
15 | feet |
16 | inches |
17 | cm |
18 | meters |
19 | rpm |
20 | degrees |
21 | lux |
22 | grampercubicmeter |
23 | var |
24 | feetpersec |
25 | lbspercubicfoot |
26 | microgrampercubicmeter |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| circuitPoleSensorMaximum The largest possible reading as an unsigned integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitP… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.11.6.1.11 |
| circuitPoleSensorMinimum The smallest possible reading as an unsigned integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuit… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.11.6.1.12 |
| circuitPoleSensorHysteresis The hysteresis used when crossing a threshold towards the normal state.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the valu… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.11.6.1.13 |
| circuitPoleSensorStateChangeDelay The delay measured in samples before a state is asserted.
If the value is zero, then the state is asserted as soon as
it is detected; if it is non-zero, say n, then the assertion
… | column | Unsigned32 | .1.3.6.1.4.1.13742.6.3.11.6.1.14 |
| circuitPoleSensorLowerCriticalThreshold The lower critical threshold as an unsigned integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitP… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.11.6.1.21 |
| circuitPoleSensorLowerWarningThreshold The lower warning threshold as an unsigned integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitPo… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.11.6.1.22 |
| circuitPoleSensorUpperCriticalThreshold The upper critical threshold as an unsigned integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitP… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.11.6.1.23 |
| circuitPoleSensorUpperWarningThreshold The upper warning threshold as an unsigned integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitPo… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.11.6.1.24 |
| circuitPoleSensorEnabledThresholds A bit string indicating which thresholds are enabled.
This parameter does not apply to sensors without numerical reading. | column | Bits | .1.3.6.1.4.1.13742.6.3.11.6.1.25 |
| circuitPoleSensorSignedMaximum The largest possible reading as a signed integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitPole… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.11.6.1.26 |
| circuitPoleSensorSignedMinimum The smallest possible reading as a signed integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitPol… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.11.6.1.27 |
| circuitPoleSensorSignedLowerCriticalThreshold The lower critical threshold as a signed integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitPole… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.11.6.1.28 |
| circuitPoleSensorSignedLowerWarningThreshold The lower warning threshold as a signed integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitPoleS… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.11.6.1.29 |
| circuitPoleSensorSignedUpperCriticalThreshold The upper critical threshold as a signed integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitPole… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.11.6.1.30 |
| circuitPoleSensorSignedUpperWarningThreshold The upper warning threshold as a signed integer.
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value is 1 and
circuitPoleS… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.11.6.1.31 |
| circuitPoleSensorLogAvailable Is data logging enabled for this sensor? | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.13742.6.3.11.6.1.4 |
| circuitPoleSensorDecimalDigits The number of digits displayed to the right of the decimal point.
This parameter does not apply to sensors without numerical reading. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.11.6.1.7 |
| circuitPoleSensorResolution The resolution: the minimum difference between any two measured values
The value of this OID variable should be scaled by
circuitPoleSensorDecimalDigits. For example, if the value… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.11.6.1.9 |