pdnAdslLineLdsf

PDN-ADSL-LINE-EXT-MIB · .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.10

Object

column r/w Enumeration

Defines whether the line should be forced into the loop
diagnostics mode by the near-end ATU on this line.
    ldsfMode0(1) - 0: Inhibits the near-end ATU from performing loop
                      diagnostics mode procedures on the line. Loop
                      diagnostic mode procedures may still be 
                      initiated by the far-end ATU.
    ldsModef1(2) - 1: Forces the near-end ATU to perform the loop
                      diagnostics procedures.
              
The line needs to be forced to the L3 state (idle state) before 
it can be forced to the loop diagnostics mode. Only while the 
line power management state is the L3 state, the line can be forced 
into the loop diagnostics mode procedures. 
              
The following are ways to force the line to the L3 state: 
(1) Set the ifAdminStatus to down.
              
When the loop diagnostics mode procedures are completed successfully,
this object shall reset to ldsf0 and the line shall return to and
remain in the L3 idle state. The loop diagnostics data shall be
available at least until the line is forced to the L0 state. If the
loop diagnostics procedures can't be completed successfully, then
an Initialization Failure occurs. As long as loop diagnostics
procedures are not completed successfully, attempts shall be made
to do so, until the loop diagnostics mode is no longer forced on 
the line through this configuration parameter.

Context

MIB: PDN-ADSL-LINE-EXT-MIB
OID: .1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.10
Type: column
Access: readwrite
Status: current
Parent: pdnAdslLineExtEntry
Table: pdnAdslLineExtTable
Siblings: 10

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	ldsfMode0
`2`	ldsfMode1

Related Objects

Sibling Objects

Object	Type	Syntax	OID
pdnAdslLineTransAtucCap The transmission modes, represented by a bitmask that the ATU-C is capable of supporting. The modes available are limited by the design of the equipment.	column	PdnAdslTransmissionModeType	`.1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.1`
pdnAdslLineL2Atprt This parameter represents the total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e.,…	column	dB Unsigned32	`.1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.11`
pdnAdslLineTransAtucConfig The transmission modes, represented by a bitmask, currently enabled by the ATU-C. The manager can only set those modes that are supported by the ATU-C. An ATU-C's supported mod…	column	PdnAdslTransmissionModeType	`.1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.2`
pdnAdslLineTransAtucActual The actual transmission mode of the ATU-C. During ADSL line initialization, the ADSL Transceiver Unit Remote terminal end (ATU-R) will determine the mode used for the link. This…	column	PdnAdslTransmissionModeType	`.1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.3`
pdnAdslLinePowerManagementConfig This object enables or disables power management functionality.	column	Enumeration	`.1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.4`
pdnAdslLineSpectrumProfile The value of this object identifies the row in the ADSL Line Spectrum Profile Table, pdnAdslLineSpectrumProfileTable, which applies for this ADSL line. If this object is not a zer…	column	OctetString	`.1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.5`
pdnAdslLinePmMode The line states the ATU-C or ATU-R may autonomously transition to on this line. It is coded in a bit-map representation (0 if not allowed, 1 if allowed) as follows: idleStateL…	column	Bits	`.1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.6`
pdnAdslLineL0Time The minimum time, in seconds, between and Exit from the L2 state and the next Entry into the L2 state.	column	seconds Unsigned32	`.1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.7`
pdnAdslLineL2Time The minimum time, in seconds, between an Entry into the L2 state and the first Power Trim in the L2 state and between two con- secutive Power Trims in the L2 State.	column	seconds Unsigned32	`.1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.8`
pdnAdslLineL2Atpr The maximum aggregate transmit power reduction, in dB, that can be performed through a single Power Trim in the L2 state. At the time this MIB was produced, the upp…	column	dB Unsigned32	`.1.3.6.1.4.1.1795.2.24.2.6.24.1.1.1.9`