oaVoaIfCurrentPowerOutOfRange

LUM-OA-MIB · .1.3.6.1.4.1.8708.2.19.2.4.1.1.20
MIB view Table view

Object

column LUM-TCFaultStatus 
Alarm raised when the current output power
is outside the 'regulation range'.
              
The regulation range is defined by
              
Wanted Output Power +/- Regulation Range
              
At this point, no regulation will be performed.
The operator must change the wantedOutputPower.

Context

MIB
LUM-OA-MIB
OID
.1.3.6.1.4.1.8708.2.19.2.4.1.1.20
Type
column
Access
readonly
Status
current
Parent
oaVoaIfEntry
Table
oaVoaIfTable
Siblings
21

Syntax

LUM-TCFaultStatus
Source
LUM-TCFaultStatus
Base type
Enumeration

Values & Constraints

Type Values
1ok
2alarm

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
oaVoaIfIndex
An arbitrary index assigned to each entry.
columnUnsigned32.1.3.6.1.4.1.8708.2.19.2.4.1.1.1
oaVoaIfOperStatus
The operational state for the interface. notPresent - The interface is not available. down - The interface is not used. up - The inter…
columnLUM-TCBoardOrInterfaceOperStatus.1.3.6.1.4.1.8708.2.19.2.4.1.1.10
oaVoaIfObjectProperty
Property mask.
columnLUM-TCObjectProperty.1.3.6.1.4.1.8708.2.19.2.4.1.1.11
oaVoaIfControlMode
The control mode of the VOA channel. constPower - regulate slowly towards a given output power. constAttenuation - set a fix attenuation…
columnEnumeration.1.3.6.1.4.1.8708.2.19.2.4.1.1.12
oaVoaIfWantedOutputPower
The wanted output power. Applicable for constPower.
columnInteger32.1.3.6.1.4.1.8708.2.19.2.4.1.1.13
oaVoaIfCurrentOutputPower
The actual output power.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.8708.2.19.2.4.1.1.14
oaVoaIfRegulationRange
An offset below the wanted output power at which the 'Current Power Out Of Range' alarm shall be raised. When the current output power is so far below the wanted ou…
columnUnsigned32.1.3.6.1.4.1.8708.2.19.2.4.1.1.15
oaVoaIfWantedAttenuation
The wanted attenuation. voa8ch: applicable for constAttenuation voa2ch: always applicable This attribute can be written via SNMP.
columnUnsigned32.1.3.6.1.4.1.8708.2.19.2.4.1.1.16
oaVoaIfCurrentAttenuation
The current attenuation. Applicable for constPower.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.8708.2.19.2.4.1.1.17
oaVoaIfSamplePeriod
The approximate period between 2 consecutive measurements of the output power
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.8708.2.19.2.4.1.1.18
oaVoaIfOuputPowerControlFailure
Alarm raised when the wanted output power can not be obtained. That is, even if the attenuation is reduced to zero, the wanted power can not be obtained.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.19.2.4.1.1.19
oaVoaIfName
The management name of the interface, for example 'voa:1:2:1'.
columnLUM-TCMgmtNameString.1.3.6.1.4.1.8708.2.19.2.4.1.1.2
oaVoaIfConfigurationCommand
Select which control mode to use: constPower constAttenuation
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.19.2.4.1.1.21
oaVoaIfInInstallationMode
Alarm raised when the VOA is put in the mode constPowerAtInstallation.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.19.2.4.1.1.22
oaVoaIfDescr
User configurable label.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.8708.2.19.2.4.1.1.3
oaVoaIfSubrack
The number of the subrack where the interface is located.
columnLUM-TCSubrackNumber.1.3.6.1.4.1.8708.2.19.2.4.1.1.4
oaVoaIfSlot
The number of the slot where the interface is located.
columnLUM-TCSlotNumber.1.3.6.1.4.1.8708.2.19.2.4.1.1.5
oaVoaIfTxPort
The number of the port where the TX part of the interface is located.
columnLUM-TCPortNumber.1.3.6.1.4.1.8708.2.19.2.4.1.1.6
oaVoaIfRxPort
The number of the port where the RX part of the interface is located.
columnLUM-TCPortNumber.1.3.6.1.4.1.8708.2.19.2.4.1.1.7
oaVoaIfInvPhysIndexOrZero
The row in the invPhysTable for this interface. Set to 0 if not known.
columnUnsigned32.1.3.6.1.4.1.8708.2.19.2.4.1.1.8
oaVoaIfAdminStatus
The administrative state for the interface. down - The interface should be inactive. service - The interface is activated but alarms are suppressed. …
columnLUM-TCBoardOrInterfaceAdminStatus.1.3.6.1.4.1.8708.2.19.2.4.1.1.9