lgpPwrAutomaticBatteryTest

LIEBERT-GP-POWER-MIB · .1.3.6.1.4.1.476.1.42.3.5.4.15
MIB view Table view

Object

scalar r/w Enumeration 
Automatic battery test option.  If enabled, the battery will be tested
on a fixed interval.  If disabled, the battery test must be initiated
by a battery test command.  The interval at which a battery test is
performed is defined by 'lgpPwrAutomaticBatteryTestInterval'.

Context

MIB
LIEBERT-GP-POWER-MIB
OID
.1.3.6.1.4.1.476.1.42.3.5.4.15
Type
scalar
Access
readwrite
Status
current
Parent
lgpPwrSettings
Siblings
20

Syntax

Enumeration

Values & Constraints

Enumerated Values
1on
2off

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
lgpPwrPreferredSource
The well known measurement source from the 'lgpPwrWellKnownMeasurements' sub-tree that is the preferred input source of the system.
scalarObjectIdentifier.1.3.6.1.4.1.476.1.42.3.5.4.1
lgpPwrAutoRestartBatteryChargeThreshold
The battery charge percentage required before the device can automatically restart.
scalarpercent SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.10
lgpPwrParallelModuleCount
The number of modules in the parallel system.
scalarCount SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.11
lgpPwrParallelRedundancyCount
The number of redundant modules in the parallel system.
scalarCount SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.12
lgpPwrLoadBusSyncMode
The configuration of Load Bus Synchronization (LBS) between independent systems.
scalarEnumeration.1.3.6.1.4.1.476.1.42.3.5.4.13
lgpPwrEconomicOperationMode
The configuration of the economic operation mode of the system.
scalarEnumeration.1.3.6.1.4.1.476.1.42.3.5.4.14
lgpPwrMinimumRedundantPowerModule
The minimum number of redundant power modules that must be present before sending a loss of power redundancy alarm. If 0, there is no redundant power functionality.
scalarCount SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.16
lgpPwrMinimumRedundantBatteryModule
The minimum number of redundant battery modules that must be present before sending an alarm. If 0, the redundant battery module alarm is disabled.
scalarCount SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.17
lgpPwrOutputToLoadUserOverloadLimit
This is the user specified maximum load the device can support without sending an alarm.
scalarVolt-Amp SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.18
lgpPwrNoLoadWarningLimit
The minimum current draw on the output in which the device considers there to be a load present on the output. The condition lgpConditionWarningNoLoadDetected will be triggered i…
scalarAmp SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.19
lgpPwrLoadOnSource
The well known measurement source from the 'lgpPwrWellKnownMeasurements' sub-tree that is currently powering the output (load).
scalarObjectIdentifier.1.3.6.1.4.1.476.1.42.3.5.4.2
lgpPwrNoLoadWarningDelay
The amount of time to delay before annunciation of the condition lgpConditionNoLoadDetectedWarning after the output current load falls below the threshold lgpPwrOutputNoLoadWarnin…
scalarminutes Integer32.1.3.6.1.4.1.476.1.42.3.5.4.20
lgpPwrEconomicOperationModeControl
The configuration of the economic operation mode of the system. Note that this supersedes lgpPwrEconomicOperationMode in newer devices.
scalarEnumeration.1.3.6.1.4.1.476.1.42.3.5.4.21
lgpPwrNominalVoltageDeviation
The nominal voltage deviation between the well known measurement source lgpPwrSource1Input and lgpPwrSource2Input.
scalarVolt SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.3
lgpPwrNominalVoltageDeviationPercent
The percentage of the nominal voltage deviation between the well known measurement source lgpPwrSource1Input and lgpPwrSource2Input.
scalarpercent SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.4
lgpPwrPhaseDifferenceLimit
The maximum phase difference (between the well known input sources ) in which a transfer to an available input source is permitted.
scalar0.1 Degrees SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.5
lgpPwrFrequencyDeviationLimit
The maximum frequency deviation (between the well known input sources ) in which a transfer to an available input source is permitted.
scalar0.1 Hertz SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.6
lgpPwrThresholdTable
A list of power thresholds for a given power measurement at a point/location in the system. The lgpPwrThresholdType in this table corresponds to the type of measurement the high a…
table-.1.3.6.1.4.1.476.1.42.3.5.4.7
lgpPwrUpsAutoRestart
The device will automatically restart when utility power is restored following a battery discharge.
scalarEnumeration.1.3.6.1.4.1.476.1.42.3.5.4.8
lgpPwrUpsAutoRestartDelay
The device will automatically delay a certain number of seconds and then restart after utility power is restored following a battery discharge. The number of seconds to delay is…
scalarseconds SNMPv2-SMIInteger32.1.3.6.1.4.1.476.1.42.3.5.4.9