jnxoptIfOChVendorTransceiverClass
JNX-OPT-IF-EXT-MIB ·
.1.3.6.1.4.1.2636.3.73.1.3.2.1.1.9
Object
column
OctetString
As defined in G.698 Vendors can summarize a set of parameters in a single proprietary parameter: the Class of transceiver. The Transceiver classification will be based on the Vendor Name and the main TX and RX parameters (i.e. Trunk Mode, Framing, Bit rate, Trunk Type etc). If this parameter is used, the MIB parameters specifying the Transceiver characteristics may not be significant and the vendor will be responsible to specify the Class contents and values. The Vendor can publish the parameters of its Classes or declare to be compatible with published Classes.(G) Optional for compliance. (not mentioned in G.698)
Context
- MIB
- JNX-OPT-IF-EXT-MIB
- OID
.1.3.6.1.4.1.2636.3.73.1.3.2.1.1.9- Type
- column
- Access
- readonly
- Status
- current
- Parent
- jnxoptIfOChConfigExtEntry
- Table
- jnxoptIfOChConfigExtTable
- Siblings
- 13
Syntax
OctetString
Values & Constraints
Object Constraints
range: 1-64
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| jnxoptIfOChMiminumChannelSpacing A minimum nominal difference in frequency (GHz) between two adjacent
channels. | column | JnxoptIfChannelSpacing | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.1 |
| jnxoptIfOChOpticalInterfaceApplicationCode This parameter indicates the transceiver application code at Ss
and Rs as defined in [ITU.G698.2] Chapter 5.3 | column | OctetString | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.10 |
| jnxoptIfOChLaserAdminState The configured State of the laser:
0 - disabled
1 - enabled | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.11 |
| jnxoptIfOChLaserOperationalState The Operational Status of Laser:
0 - disabled
1 - Enabled
2 - fault
3 - degraded | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.12 |
| jnxoptIfOChAdminState The Administrative Status of an Interface:
0 - Out of Service
1 - In Service | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.13 |
| jnxoptIfOChOperationalState The Operational Status of an Interface:
0 - disabled
1 - enabled
2 - Fault
3 - Degraded | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.14 |
| jnxoptIfOChBitRateLineCoding Optical tributary signal class
NRZ 2.5G (from nominally 622 Mbit/s to nominally 2.67 Gbit/s)
NRZ 10G (nominally 2.4 Gbit/s to nominally 10.71 Gbit/s) | column | JnxoptIfBitRateLineCoding | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.2 |
| jnxoptIfOChFEC This parameter indicates what Forward Error Correction (FEC) code
is used at Source and Sink.
GFEC (from G709) and the I.x EFEC's
(G.975 - Table I.1 super FEC).
1 - No FEC
2 -… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.3 |
| jnxoptIfOChSinkMaximumBERMantissa This parameter indicate the maximum Bit(mantissa) error rate can be
supported by the application at the Receiver. In case of FEC
applications it is intended after the FEC correct… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.4 |
| jnxoptIfOChSinkMaximumBERExponent This parameter indicate the maximum Bit(exponent) error rate can be
supported by the application at the Receiver. In case of FEC
applications it is intended after the FEC correct… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.5 |
| jnxoptIfOChMinWavelength This parameter indicate minimum wavelength spectrum in a
definite wavelength Band (L, C and S) | column | 0.01 nm SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.6 |
| jnxoptIfOChMaxWavelength This parameter indicate maximum wavelength spectrum in a
definite wavelength Band (L, C and S) | column | 0.01 nm SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.7 |
| jnxoptIfOChWavelength This parameter indicates the wavelength value. | column | 0.01 nm SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.8 |