jnxoptIfOChSinkMaximumBERMantissa
JNX-OPT-IF-EXT-MIB ·
.1.3.6.1.4.1.2636.3.73.1.3.2.1.1.4
Object
column
SNMPv2-SMIUnsigned32
This parameter indicate the maximum Bit(mantissa) error rate can be supported by the application at the Receiver. In case of FEC applications it is intended after the FEC correction.
Context
- MIB
- JNX-OPT-IF-EXT-MIB
- OID
.1.3.6.1.4.1.2636.3.73.1.3.2.1.1.4- Type
- column
- Access
- readonly
- Status
- current
- Parent
- jnxoptIfOChConfigExtEntry
- Table
- jnxoptIfOChConfigExtTable
- Siblings
- 13
Syntax
SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| jnxoptIfOChMiminumChannelSpacing A minimum nominal difference in frequency (GHz) between two adjacent
channels. | column | JnxoptIfChannelSpacing | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.1 |
| jnxoptIfOChOpticalInterfaceApplicationCode This parameter indicates the transceiver application code at Ss
and Rs as defined in [ITU.G698.2] Chapter 5.3 | column | OctetString | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.10 |
| jnxoptIfOChLaserAdminState The configured State of the laser:
0 - disabled
1 - enabled | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.11 |
| jnxoptIfOChLaserOperationalState The Operational Status of Laser:
0 - disabled
1 - Enabled
2 - fault
3 - degraded | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.12 |
| jnxoptIfOChAdminState The Administrative Status of an Interface:
0 - Out of Service
1 - In Service | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.13 |
| jnxoptIfOChOperationalState The Operational Status of an Interface:
0 - disabled
1 - enabled
2 - Fault
3 - Degraded | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.14 |
| jnxoptIfOChBitRateLineCoding Optical tributary signal class
NRZ 2.5G (from nominally 622 Mbit/s to nominally 2.67 Gbit/s)
NRZ 10G (nominally 2.4 Gbit/s to nominally 10.71 Gbit/s) | column | JnxoptIfBitRateLineCoding | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.2 |
| jnxoptIfOChFEC This parameter indicates what Forward Error Correction (FEC) code
is used at Source and Sink.
GFEC (from G709) and the I.x EFEC's
(G.975 - Table I.1 super FEC).
1 - No FEC
2 -… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.3 |
| jnxoptIfOChSinkMaximumBERExponent This parameter indicate the maximum Bit(exponent) error rate can be
supported by the application at the Receiver. In case of FEC
applications it is intended after the FEC correct… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.5 |
| jnxoptIfOChMinWavelength This parameter indicate minimum wavelength spectrum in a
definite wavelength Band (L, C and S) | column | 0.01 nm SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.6 |
| jnxoptIfOChMaxWavelength This parameter indicate maximum wavelength spectrum in a
definite wavelength Band (L, C and S) | column | 0.01 nm SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.7 |
| jnxoptIfOChWavelength This parameter indicates the wavelength value. | column | 0.01 nm SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.8 |
| jnxoptIfOChVendorTransceiverClass As defined in G.698
Vendors can summarize a set of parameters in a
single proprietary parameter: the Class of transceiver. The
Transceiver classification will be based on the Ven… | column | OctetString | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.9 |