jnxoptIfOChOperationalState
JNX-OPT-IF-EXT-MIB ·
.1.3.6.1.4.1.2636.3.73.1.3.2.1.1.14
Object
column
Enumeration
The Operational Status of an Interface: 0 - disabled 1 - enabled 2 - Fault 3 - Degraded
Context
- MIB
- JNX-OPT-IF-EXT-MIB
- OID
.1.3.6.1.4.1.2636.3.73.1.3.2.1.1.14- Type
- column
- Access
- readonly
- Status
- current
- Parent
- jnxoptIfOChConfigExtEntry
- Table
- jnxoptIfOChConfigExtTable
- Siblings
- 13
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | disabled |
1 | enabled |
2 | fault |
3 | degraded |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| jnxoptIfOChMiminumChannelSpacing A minimum nominal difference in frequency (GHz) between two adjacent
channels. | column | JnxoptIfChannelSpacing | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.1 |
| jnxoptIfOChOpticalInterfaceApplicationCode This parameter indicates the transceiver application code at Ss
and Rs as defined in [ITU.G698.2] Chapter 5.3 | column | OctetString | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.10 |
| jnxoptIfOChLaserAdminState The configured State of the laser:
0 - disabled
1 - enabled | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.11 |
| jnxoptIfOChLaserOperationalState The Operational Status of Laser:
0 - disabled
1 - Enabled
2 - fault
3 - degraded | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.12 |
| jnxoptIfOChAdminState The Administrative Status of an Interface:
0 - Out of Service
1 - In Service | column | Enumeration | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.13 |
| jnxoptIfOChBitRateLineCoding Optical tributary signal class
NRZ 2.5G (from nominally 622 Mbit/s to nominally 2.67 Gbit/s)
NRZ 10G (nominally 2.4 Gbit/s to nominally 10.71 Gbit/s) | column | JnxoptIfBitRateLineCoding | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.2 |
| jnxoptIfOChFEC This parameter indicates what Forward Error Correction (FEC) code
is used at Source and Sink.
GFEC (from G709) and the I.x EFEC's
(G.975 - Table I.1 super FEC).
1 - No FEC
2 -… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.3 |
| jnxoptIfOChSinkMaximumBERMantissa This parameter indicate the maximum Bit(mantissa) error rate can be
supported by the application at the Receiver. In case of FEC
applications it is intended after the FEC correct… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.4 |
| jnxoptIfOChSinkMaximumBERExponent This parameter indicate the maximum Bit(exponent) error rate can be
supported by the application at the Receiver. In case of FEC
applications it is intended after the FEC correct… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.5 |
| jnxoptIfOChMinWavelength This parameter indicate minimum wavelength spectrum in a
definite wavelength Band (L, C and S) | column | 0.01 nm SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.6 |
| jnxoptIfOChMaxWavelength This parameter indicate maximum wavelength spectrum in a
definite wavelength Band (L, C and S) | column | 0.01 nm SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.7 |
| jnxoptIfOChWavelength This parameter indicates the wavelength value. | column | 0.01 nm SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.8 |
| jnxoptIfOChVendorTransceiverClass As defined in G.698
Vendors can summarize a set of parameters in a
single proprietary parameter: the Class of transceiver. The
Transceiver classification will be based on the Ven… | column | OctetString | .1.3.6.1.4.1.2636.3.73.1.3.2.1.1.9 |