hwPPPoESmltCurrentPhase
HUAWEI-IPDSLAM-PPPOE-MIB ·
.1.3.6.1.4.1.2011.6.107.2.1.7
Object
column
Enumeration
Indicates the current stage of the simulation.
Options:
1. discovery(1) -indicates the discovery stage of PPPoE dialup
2. lcp(2) -indicates the LCP negotiation stage. In this stage,
the parameters required for creating, maintaining, and
terminating the PPP networking are negotiated.
3. authentication(3) -indicates the authentication stage. In this stage,
the user is authenticated after the PPPoE connection is
set up.
4. ncp(4) -indicates the NCP negotiation stage. In this stage, the
network-layer compression protocol and IP address are
negotiated.
5. online(5) -indicates the data transmission stage
6. stop(6) -indicates that PPPoE dialup is not performed
Context
- MIB
- HUAWEI-IPDSLAM-PPPOE-MIB
- OID
.1.3.6.1.4.1.2011.6.107.2.1.7- Type
- column
- Access
- readonly
- Status
- current
- Parent
- hwPPPoESmltAdminEntry
- Table
- hwPPPoESmltAdminTable
- Siblings
- 14
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | discovery |
2 | lcp |
3 | authentication |
4 | ncp |
5 | online |
6 | stop |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwPPPoESmltObjIndex Indicates the index of hwPPPoESmltAdminTable.
This leaf means the dialup ID. Currently, only
one user is supported. The maximum value of the
index is 1.
If you specify it to 42… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.107.2.1.1 |
| hwPPPoESmltEndTime Indicates the simulation end time.
Data type: DateAndTime.
For example, 2010-2-6,1:38:50.0,+8:0. | column | SNMPv2-TCDateAndTime | .1.3.6.1.4.1.2011.6.107.2.1.10 |
| hwPPPoESmltUserSessionId Indicates the obtained session ID of the user.
Range: 1-4294967295 | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2011.6.107.2.1.11 |
| hwPPPoESmltUserIp Indicates the obtained IP address of the user.
Data type: IpAddress. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2011.6.107.2.1.12 |
| hwPPPoESmltGatewayIp Indicates the obtained gateway IP address.
Data type: IpAddress. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2011.6.107.2.1.13 |
| hwPPPoESmltRowStatus Indicates the row status. It is used for starting or stopping the
PPPoE dialup simulation service. Only options active(1), createAndGo(4),
and destroy(6) are supported.
To start… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.2011.6.107.2.1.14 |
| hwPPPoESmltUserMac Indicates the user-side MAC address. It is an optional parameter. By default, it is bridge MAC address. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2011.6.107.2.1.15 |
| hwPPPoESmltSrvFlowIndex Indicates the service port ID. Here, it refers to the ID of a service port
that is already created on the current device. The service port ID on the
NMS is larger than the servi… | column | Integer32 | .1.3.6.1.4.1.2011.6.107.2.1.2 |
| hwPPPoESmltUserName Indicates the user name. | column | OctetString | .1.3.6.1.4.1.2011.6.107.2.1.3 |
| hwPPPoESmltUserPassword Indicates the user password for authentication. | column | OctetString | .1.3.6.1.4.1.2011.6.107.2.1.4 |
| hwPPPoESmltAuthMode Indicates the user authentication mode. Currently, the device supports two modes,
Options:
1. chap(1) -Challenge-Handshake Authentication Protocol mode
2. pap(2) -Password Authe… | column | Enumeration | .1.3.6.1.4.1.2011.6.107.2.1.5 |
| hwPPPoESmltOverTime Indicates the test timeout time. It is an optional parameter.
Unit: second
Range: 5-60
Default: 5 | column | Integer32 | .1.3.6.1.4.1.2011.6.107.2.1.6 |
| hwPPPoESmltResult Indicates the simulation result.
Options:
1. success(0) -indicates the PPPoE simulation is success
2. otherError(1) -indicates other errors
3. timeout(2) … | column | Enumeration | .1.3.6.1.4.1.2011.6.107.2.1.8 |
| hwPPPoESmltStartTime Indicates the simulation start time.
Data type: DateAndTime.
For example, 2010-2-6,1:38:50.0,+8:0. | column | SNMPv2-TCDateAndTime | .1.3.6.1.4.1.2011.6.107.2.1.9 |