hpicfPoePethPsePortPowerMode
HP-ICF-POE-MIB ·
.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.10
Object
column
Enumeration
This field specifies the power mode of the port whether enabled or disabled or disableWithFiber
Context
- MIB
- HP-ICF-POE-MIB
- OID
.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.10- Type
- column
- Access
- readonly
- Status
- current
- Parent
- hpicfPoePethPsePortEntry
- Table
- hpicfPoePethPsePortTable
- Siblings
- 16
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | enable |
2 | disable |
6 | disableWithFiber |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hpicfPoePethPsePortCurrent This field specifies the current supplied at this port.
This value is specified in milli amperes(mA). | column | Integer32 | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.1 |
| hpicfPoePethPsePortAveragePower This field specifies the average power supplied to this port
which is used by the device connected to it. | column | watts SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.11 |
| hpicfPoePethPsePortPeakPower This field specifies the peak power supplied to this port
which is used by the device connected to it. | column | watts SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.12 |
| hpicfPoePethPsePortPreStdDetect This field specifies the pre standard detect status
for this port.
A value of On - indicates that power
pre-802.3af-standard devices.
A value of Off - indicates that only
pre-8… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.13 |
| hpicfPoePethPsePortLowPriority This object indicates whether a particular port
shuts down in the event of any PSU failure in the
system. A value of (1) indicates a low priority port
which shuts down in the even… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.14 |
| hpicfPoePethPsePortResetState This object is used to reset the
PoE controller HW to which the
port is associated. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.15 |
| hpicfPoePethPsePortPowerType This field specifies the PD type determined
during physical layer classification. The default value is -1. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.16 |
| hpicfPoePethPsePortForceTwoPairMode This field specifies the force two pair mode status
for this port.This applies only on devices that support
4 pair POE.
A value of On - indicates that force two pair
mode has been… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.17 |
| hpicfPoePethPsePortVoltage This field specifies the Voltage supplied at this port.
This value is specified in 10's of volts (dV) | column | Integer32 | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.2 |
| hpicfPoePethPsePortPower This field specifies the Power supplied at this port.
This value is specified in milliwatts (mW). | column | Integer32 | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.3 |
| hpicfPoePethPsePortPowerAllocateBy This field specifies the power allocation method for this port.
The default value is usage. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.4 |
| hpicfPoePethPsePortPowerValue This field specifies the power allocation defined for this port.
This value is specified in Watts (W). | column | Integer32 | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.5 |
| hpicfPoePethPsePortLLDPDetect This field specifies if power should be allocated using
LLDP advertised information regarding the PD. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.6 |
| hpicfPoePethPsePortPoePlusPowerValue This field specifies the power allocation defined
for this port. Use this object for equipment
supporting high power, that is greater than 15
Watts. This value is specified in W… | column | Watts Integer32 | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.7 |
| hpicfPoePethPsePortActualPower This field specifies the actual power drained by the device
connected to this port. | column | milli-watts SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.8 |
| hpicfPoePethPsePortOperStatus This field specifies the operational status of the port | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.9 |