hpicfPoePethPsePortPoePlusPowerValue

HP-ICF-POE-MIB · .1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.7
MIB view Table view

Object

column r/w Watts Integer32 
This field specifies the power allocation defined
for this port. Use this object for equipment
supporting high power, that is greater than 15  
Watts. This value is specified in Watts (W). This 
object may only be read or written when               
hpicfPoePethPsePortPowerAllocateBy is set to  
value(3). For 2540, 2930F, 2930M, 3810 and 5400R
platforms the default value is 15 Watts and for other
platforms the default value is 17 Watts.

Context

MIB
HP-ICF-POE-MIB
OID
.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.7
Type
column
Access
readwrite
Status
current
Units
Watts
Parent
hpicfPoePethPsePortEntry
Table
hpicfPoePethPsePortTable
Siblings
16

Syntax

Watts Integer32

Values & Constraints

Object Constraints
range: 0-255

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
hpicfPoePethPsePortCurrent
This field specifies the current supplied at this port. This value is specified in milli amperes(mA).
columnInteger32.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.1
hpicfPoePethPsePortPowerMode
This field specifies the power mode of the port whether enabled or disabled or disableWithFiber
columnEnumeration.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.10
hpicfPoePethPsePortAveragePower
This field specifies the average power supplied to this port which is used by the device connected to it.
columnwatts SNMPv2-SMIInteger32.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.11
hpicfPoePethPsePortPeakPower
This field specifies the peak power supplied to this port which is used by the device connected to it.
columnwatts SNMPv2-SMIInteger32.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.12
hpicfPoePethPsePortPreStdDetect
This field specifies the pre standard detect status for this port. A value of On - indicates that power pre-802.3af-standard devices. A value of Off - indicates that only pre-8…
columnEnumeration.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.13
hpicfPoePethPsePortLowPriority
This object indicates whether a particular port shuts down in the event of any PSU failure in the system. A value of (1) indicates a low priority port which shuts down in the even…
columnEnumeration.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.14
hpicfPoePethPsePortResetState
This object is used to reset the PoE controller HW to which the port is associated.
columnEnumeration.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.15
hpicfPoePethPsePortPowerType
This field specifies the PD type determined during physical layer classification. The default value is -1.
columnEnumeration.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.16
hpicfPoePethPsePortForceTwoPairMode
This field specifies the force two pair mode status for this port.This applies only on devices that support 4 pair POE. A value of On - indicates that force two pair mode has been…
columnEnumeration.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.17
hpicfPoePethPsePortVoltage
This field specifies the Voltage supplied at this port. This value is specified in 10's of volts (dV)
columnInteger32.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.2
hpicfPoePethPsePortPower
This field specifies the Power supplied at this port. This value is specified in milliwatts (mW).
columnInteger32.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.3
hpicfPoePethPsePortPowerAllocateBy
This field specifies the power allocation method for this port. The default value is usage.
columnEnumeration.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.4
hpicfPoePethPsePortPowerValue
This field specifies the power allocation defined for this port. This value is specified in Watts (W).
columnInteger32.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.5
hpicfPoePethPsePortLLDPDetect
This field specifies if power should be allocated using LLDP advertised information regarding the PD.
columnEnumeration.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.6
hpicfPoePethPsePortActualPower
This field specifies the actual power drained by the device connected to this port.
columnmilli-watts SNMPv2-SMIInteger32.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.8
hpicfPoePethPsePortOperStatus
This field specifies the operational status of the port
columnEnumeration.1.3.6.1.4.1.11.2.14.11.1.9.1.1.1.9