cpqNicIfLogMapGroupType

CPQNIC-MIB · .1.3.6.1.4.1.232.18.2.2.1.1.4
MIB view Table view

Object

column mandatory Enumeration 
The type of Fault Tolerance supplied by this logical adapter.
              
The following types of Fault Tolerance are supported:
              
unknown(1)
  Indicates that the instrument agent does not recognize the
  controller.  You may need to upgrade the instrument agent.
              
none(2)
  Indicates the logical adapter is not fault tolerant.
  There is a single physical adapter associated with the
  logical adapter.
              
redundantPair(3)
  Indicates that the logical adapter has two adapters associated
  with it.  One adapter is active and the other adapter is a
  hot standby.  No longer used.
              
nft(4)
  Network Fault Tolerance.  The logical adapter has two or more
  adapters associated with it.  One adapter is active on the
  network and the other(s) are hot standby(s).
              
alb(5)
  Adaptive Load Balancing. Indicates that the logical adapter has
  more than one physical adapter associated with it.  One adapter
  transmits and receives, while the others only transmit.  If the
  receiving adapter fails, one of the other adapters assumes this
  role.  No longer used.
              
fec(6)
  Fast EtherChannel.  This allows all physical adapters
  associated with the logical adapter to both receive and
  transmit.  This requires a switch that cooperates with
  the adapters.  If any adapter fails, the load is spread
  among the remaining adapters.  No longer used.
              
gec(7)
  Gigabit EtherChannel.  This allows all physical adapters
  associated with the logical adapter to both receive and
  transmit.  This requires a gigabit switch that cooperates
  with the adapters.  If any adapter fails, the load is
  spread among the remaining adapters.  No longer used.
              
ad(8)
  IEEE802.3ad Link Aggregation.  This allows all physical
  adapters associated with the logical adapter to both receive
  and transmit.  This requires a switch that cooperates with
  the adapters.  If any adapter fails, the load is spread
  among the remaining adapters.  No longer used.
              
slb(9)
  Switch-assisted load balancing.  This allows all physical
  adapters associated with the logical adapter to both receive
  and transmit.  This requires a switch that cooperates with
  the adapters.  If any adapter fails, the load is spread
  among the remaining adapters.  Aggregates fec, gec, and ad.
              
tlb(10)
  Transmit Load Balancing. Indicates that the logical adapter has
  more than one physical adapter associated with it.  One adapter
  transmits and receives, while the others only transmit.  If the
  receiving adapter fails, one of the other adapters assumes this
  role.  Formerly alb.
               
		 redundancySet(11)
  Indicates that the logical adapter has more than one adapter associated
  with it. This value is used when the type of the team could not be determined.
              
		 switchInd(12)
			 The teaming will work with any Ethernet switches - even non-intelligent switches.
              
		 lacp(13)
			IEEE 802.1ax works by using the Link Aggregation Control Protocol (LACP) to 
			dynamically identify links that are connected between the host and a given switch. 
              
		 team(14)
			just team.

Context

MIB
CPQNIC-MIB
OID
.1.3.6.1.4.1.232.18.2.2.1.1.4
Type
column
Access
readonly
Status
mandatory
Parent
cpqNicIfLogMapEntry
Table
cpqNicIfLogMapTable
Siblings
22

Syntax

Enumeration

Values & Constraints

Enumerated Values
1unknown
2none
3redundantPair
4nft
5alb
6fec
7gec
8ad
9slb
10tlb
11redundancySet
12switchInd
13lacp
14team

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
cpqNicIfLogMapIndex mandatory
An index that uniquely specifies this entry.
columnInteger32.1.3.6.1.4.1.232.18.2.2.1.1.1
cpqNicIfLogMapCondition mandatory
The condition of this interface. This value represents the overall condition of the logical adapter group. This value is driven by the cpqNicIfLogMapStatus object a…
columnEnumeration.1.3.6.1.4.1.232.18.2.2.1.1.10
cpqNicIfLogMapStatus mandatory
The status of the logical group. The following values are valid for the logical group status: unknown(1) The instrument agent may not support this …
columnEnumeration.1.3.6.1.4.1.232.18.2.2.1.1.11
cpqNicIfLogMapNumSwitchovers mandatory
The number of times a fault tolerant switchover has occurred. Switchovers occur because the primary adapter fails.
columnRFC1155-SMICounter.1.3.6.1.4.1.232.18.2.2.1.1.12
cpqNicIfLogMapHwLocation optional
A text description of the hardware location, on complex multi SBB hardware only, for the adapters. A NULL string indicates that the hardware location could not be determined or is…
columnOctetString.1.3.6.1.4.1.232.18.2.2.1.1.13
cpqNicIfLogMapSpeed mandatory
An estimate of the interface`s current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this obje…
columnRFC1155-SMIGauge.1.3.6.1.4.1.232.18.2.2.1.1.14
cpqNicIfLogMapVlanCount mandatory
The number of VLANs associated with this logical adapter.
columnInteger32.1.3.6.1.4.1.232.18.2.2.1.1.15
cpqNicIfLogMapVlans mandatory
An array of octets corresponding to the indices in the cpqNicIfVlanMapTable of the VLANs associated with this logical adapter. The number of octets is equal to cpqNicIfLogMapVlan…
columnOctetString.1.3.6.1.4.1.232.18.2.2.1.1.16
cpqNicIfLogMapLastChange mandatory
The time the underlying link associated with this interface changed its status from either link up to link down or link down to link up.
columnRFC1155-SMITimeTicks.1.3.6.1.4.1.232.18.2.2.1.1.17
cpqNicIfLogMapAdvancedTeaming mandatory
This bitmap indicates the advanced features being used by the logical adapter (team). cpqNicIfLogMapAdvancedTeaming AND 1 is 1, Active Path Failover is enabled. cpqNicIfLogMapAdva…
columnInteger32.1.3.6.1.4.1.232.18.2.2.1.1.18
cpqNicIfLogMapSpeedMbps optional
An estimate of the interface`s current bandwidth in Megabits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this …
columnRFC1155-SMIGauge.1.3.6.1.4.1.232.18.2.2.1.1.19
cpqNicIfLogMapIfNumber mandatory
An OCTET STRING representing an array of MIB II Interface Numbers implemented by this logical adapter. Each entry is a 32-bit value, represented by 4 octets in LSB...MSB (Little-E…
columnOctetString.1.3.6.1.4.1.232.18.2.2.1.1.2
cpqNicIfLogMapIPV6Address optional
The CIDR(Classless Inter-Domain Routing) notation that the logical adapter presents to the network.
columnRFC1213-MIBDisplayString.1.3.6.1.4.1.232.18.2.2.1.1.20
cpqNicIfLogMapLACNumber optional
Local Area Connection number that the logical adapter presents to the network.
columnRFC1213-MIBDisplayString.1.3.6.1.4.1.232.18.2.2.1.1.21
cpqNicIfLogMapDHCP mandatory
This value indicates whether logical adapter ip address was obtained via a DHCP server. The following values are valid: true(1) ip address is a dhcp…
columnEnumeration.1.3.6.1.4.1.232.18.2.2.1.1.22
cpqNicIfLogMapPciLocation optional
A string designating the PCI device location for the controller, following the format DDDD:BB:DD.F, where DDDD is the PCI domain number, BB is the PCI bus number, DD is the PCI de…
columnOctetString.1.3.6.1.4.1.232.18.2.2.1.1.23
cpqNicIfLogMapDescription mandatory
Description of the logical adapter. This string is NULL terminated.
columnOctetString.1.3.6.1.4.1.232.18.2.2.1.1.3
cpqNicIfLogMapAdapterCount mandatory
The number of physical adapters associated with this logical adapter.
columnInteger32.1.3.6.1.4.1.232.18.2.2.1.1.5
cpqNicIfLogMapAdapterOKCount mandatory
The number of physical adapters associated with this logical adapter that have an OK condition.
columnInteger32.1.3.6.1.4.1.232.18.2.2.1.1.6
cpqNicIfLogMapPhysicalAdapters mandatory
An array of octets corresponding to the indices in the cpqNicIfPhysAdapterTable of the physical adapters associated with this logical adapter. The number of octets is equal to cp…
columnOctetString.1.3.6.1.4.1.232.18.2.2.1.1.7
cpqNicIfLogMapMACAddress mandatory
The MAC (physical) address that the logical adapter presents to the network.
columnOctetString.1.3.6.1.4.1.232.18.2.2.1.1.8
cpqNicIfLogMapSwitchoverMode mandatory
The algorithm used to determine when to switch network traffic from one adapter to another. The following algorithms are supported: unknown(1) Indi…
columnEnumeration.1.3.6.1.4.1.232.18.2.2.1.1.9