dataPortFiberStatusTrap
CAMBIUM-PTP800-MIB ·
.1.3.6.1.4.1.17713.8.99.0.18
Object
notification
If the fiber interface on the data Ethernet port is not OK, there are three possible causes: 1) the fiber interface has been installed but disabled, 2) the interface could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the interface is disabled at the other end of the fiber link), or 3) the interface could not be established and LOS is detected (i.e. no optical carrier is detected). NB: a change of status may generate an SNMP trap and/or SMTP email alert
Context
- MIB
- CAMBIUM-PTP800-MIB
- OID
.1.3.6.1.4.1.17713.8.99.0.18- Type
- notification
- Status
- current
- Parent
- ptpTrapPrefix
- Siblings
- 32
Syntax
No syntax metadata recorded.
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| alignmentModeTrap Indicates if the unit is undergoing alignment. NB: a
change of state during operation may generate an SNMP
trap and/or SMTP email alert | notification | - | .1.3.6.1.4.1.17713.8.99.0.10 |
| unitOutOfCalibrationTrap The unit is out of calibration | notification | - | .1.3.6.1.4.1.17713.8.99.0.11 |
| encryptionEnabledMismatchTrap Encryption has been enabled on one end of the wireless
link but not the other | notification | - | .1.3.6.1.4.1.17713.8.99.0.13 |
| dataPortDisabledWarningTrap The SNMP ifAdminStatus of the data Ethernet interface
has disabled Ethernet traffic | notification | - | .1.3.6.1.4.1.17713.8.99.0.17 |
| dataPortConfigurationMismatchTrap The detection of Ethernet fragments (runt packets) on
the data Ethernet port when the link is in full duplex is
an indication of an auto-negotiation or forced
configuration mis… | notification | - | .1.3.6.1.4.1.17713.8.99.0.19 |
| softwareVersionRemoteCompatibilityTrap Indicates a mismatch of software versions at the two
ends of the wireless link | notification | - | .1.3.6.1.4.1.17713.8.99.0.20 |
| sNTPSyncTrap If SNTP Sync fails then check the server settings in the
Remote Management page, or disable SNTP. NB: a change of
state may generate an SNMP trap and/or SMTP email alert | notification | - | .1.3.6.1.4.1.17713.8.99.0.21 |
| managementPortStatusTrap Current status of the out-of-band management Ethernet
link | notification | - | .1.3.6.1.4.1.17713.8.99.0.23 |
| managementPortDisabledWarningTrap The SNMP ifAdminStatus of the out-of-band management
Ethernet interface has disabled Ethernet traffic | notification | - | .1.3.6.1.4.1.17713.8.99.0.24 |
| rFUStatusTrap Current status of the RFU. A state of 'ok' indicates
that the RFU is fully operational, although may not be
transmitting. | notification | - | .1.3.6.1.4.1.17713.8.99.0.27 |
| managementPortConfigurationMismatchTrap The detection of Ethernet fragments (runt packets) on
the out-of-band management Ethernet port when the link is
in full duplex is an indication of an auto-negotiation or
forced… | notification | - | .1.3.6.1.4.1.17713.8.99.0.28 |
| wirelessLinkStatusTrap Current status of the wireless link | notification | - | .1.3.6.1.4.1.17713.8.99.0.29 |
| dataPortStatusTrap Current status of the data Ethernet link. NB: a change
of state may generate an SNMP trap and/or SMTP email
alert | notification | - | .1.3.6.1.4.1.17713.8.99.0.3 |
| protectionAvailabilityStatusTrap In a 1+1 Hot Standby configuration, the Protection
Availability Status attribute indicates whether the
Active unit is currently being protected by the Inactive
unit. If it isn'… | notification | - | .1.3.6.1.4.1.17713.8.99.0.31 |
| protectionConfigurationStatusTrap In a 1+1 Hot Standby configuration, this attribute will
indicate whether the configuration will support
protection. | notification | - | .1.3.6.1.4.1.17713.8.99.0.32 |
| protectionStateTrap In a 1+1 Hot Standby configuration, only one CMU / RFU
at a given end of the link is Active at any one time, the
neighbor CMU / RFU being Inactive. The Protection State
attribu… | notification | - | .1.3.6.1.4.1.17713.8.99.0.33 |
| wirelessReceiveSignalStatusTrap The Wireless Receive Signal Status indicates if the
receiver is able to demodulate the transmit signal from
the remote end of the link. If it cannot demodulate the
signal, a pr… | notification | - | .1.3.6.1.4.1.17713.8.99.0.34 |
| licensedTransmitCapacityStatusTrap In a 1+1 Hot Standby configuration, the Licensed
Transmit Capacity Status attribute indicates when the
Licensed Transmit Capacity is below that of its
neighbor. | notification | - | .1.3.6.1.4.1.17713.8.99.0.36 |
| dataPortEthernetSpeedStatusTrap In a 1+1 Hot Standby configuration, the Data Port
Ethernet Speed Status attribute indicates if the Ethernet
Speed of the Data Port is below that of its neighbor. | notification | - | .1.3.6.1.4.1.17713.8.99.0.37 |
| managementPortEthernetSpeedStatusTrap In a 1+1 Hot Standby configuration, the Management Port
Ethernet Speed Status attribute indicates if the Ethernet
Speed of the Management Port is below that of its
neighbor. | notification | - | .1.3.6.1.4.1.17713.8.99.0.38 |
| protectionInterfaceStatusTrap In a 1+1 Hot Standby configuration, information is
shared between neighbor CMUs over the Protection
Interface. The Protection Interface Status attribute
reports whether the nei… | notification | - | .1.3.6.1.4.1.17713.8.99.0.39 |
| syslogStateTrap The syslog service has been enabled or disabled | notification | - | .1.3.6.1.4.1.17713.8.99.0.40 |
| syslogLocalNearlyFullTrap The syslog local log is nearly full (90%) | notification | - | .1.3.6.1.4.1.17713.8.99.0.41 |
| syslogLocalWrappedTrap The syslog local log has wrapped | notification | - | .1.3.6.1.4.1.17713.8.99.0.42 |
| secureModeAlarmTrap The secure mode (e.g. FIPS, UC-APL) state of the unit.
The secure mode is not configured(1) state indicates that
the unit is capable of secure mode operation, and one or
more o… | notification | - | .1.3.6.1.4.1.17713.8.99.0.43 |
| endWirelessReceiveSignalStatusTrap The End Wireless Receive Signal Status indicates if the
end of a link is unable to demodulate the signal
transmitted from the remote end of the link. When
Protection is set to … | notification | - | .1.3.6.1.4.1.17713.8.99.0.44 |
| rxDiversityDataPortStatusTrap When Receive Diversity is enabled, the Inactive CMU
sends Rx Diversity Ethernet Frames to the Active CMU.
Before sending these frames, the Data Port MUST be
negotiated at 1000 … | notification | - | .1.3.6.1.4.1.17713.8.99.0.45 |
| rxDiversityAvailabilityStatusTrap The Rx Diversity Availability Status attribute will
indicate when Receive Diversity is not operating
correctly, either due to a fault or due to an incorrect
configuration | notification | - | .1.3.6.1.4.1.17713.8.99.0.46 |
| rxDiversityConfigurationStatusTrap For Receive Diversity to operate correctly, certain
attributes must be configured correctly on both neighbor
CMUs. The Rx Diversity Configuration Status attribute
will indicate… | notification | - | .1.3.6.1.4.1.17713.8.99.0.47 |
| rFUPowerButtonPressedTrap IRFU power button have been pressed, IFRU has powered
down unexpectedly | notification | - | .1.3.6.1.4.1.17713.8.99.0.48 |
| syslogClientTrap Enable or disable the syslog client | notification | - | .1.3.6.1.4.1.17713.8.99.0.49 |
| linkNameMismatchTrap Signaling was received with the wrong Link Name. Either
the Link Name is configured differently at each end of
the wireless link, or this unit is aligned to the wrong
link part… | notification | - | .1.3.6.1.4.1.17713.8.99.0.9 |
Notification Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dataPortFiberStatus If the fiber interface on the data Ethernet port is not
OK, there are three possible causes: 1) the fiber
interface has been installed but disabled, 2) the
interface could not … | scalar | Enumeration | .1.3.6.1.4.1.17713.8.13.8 |