TPLINK-MLDSNOOPING-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
6
Rows
6
Columns
36

tpMldPortTable

table
.1.3.6.1.4.1.11863.6.43.1.1.2.1 · 1 row entry · 3 columns
Open in standard view 
MLD Snooping (Internet Group Management Protocol Snooping) 
is a multicast control mechanism running on Layer 2 switch. 
It can effectively prevent multicast groups being broadcasted 
in the network.
tpMldPortEntry entry .1.3.6.1.4.1.11863.6.43.1.1.2.1.1
An entry contains of the information of port configure.
Indexes
Column Syntax OID
tpMldSnoopingPortEnable
Select Enable/Disable MLD Snooping for the desired port.
0. Disable
1. Enable
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.43.1.1.2.1.1.2
tpMldFastLeavePortEnable
Select Enable/Disable Fast Leave feature for the desired port.
If Fast Leave is enabled for a port, the Switch will immediately
remove this port from the multicast group upon receiving MLD
leave messages.
0. Disable
…
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.43.1.1.2.1.1.3
tpMldPortLag
Displays the LAG number which the port belongs to.
OctetString
Constraints:
range: 0-255
 .1.3.6.1.4.1.11863.6.43.1.1.2.1.1.4

tpMldVlanTable

table
.1.3.6.1.4.1.11863.6.43.1.1.3.1 · 1 row entry · 16 columns
Open in standard view 
Multicast groups established by MLD Snooping are based on VLANs. 
You can configure different MLD parameters for different VLANs.
tpMldVlanEntry entry .1.3.6.1.4.1.11863.6.43.1.1.3.1.1
An entry contains of the information of mldsnooping.
Indexes
tpMldVlanId
Column Syntax OID
tpMldVlanId
Enter the VLAN ID to enable MLD Snooping for the desired VLAN,1-4094.
Integer32
Constraints:
range: 1-4094
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.1
tpMldVlanEnable
Select Enable/Disable MLD Snooping for the desired vlan.
0. Disable
1. Enable
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.2
tpMldVlanFastLeave
Select Enable/Disable Fast Leave feature for the desired vlan.
If Fast Leave is enabled for a vlan, the Switch will immediately
remove this port from the multicast group upon receiving MLD
leave messages.
0. Disable
…
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.3
tpMldVlanReportSuppression
Select Enable/Disable MLD Snooping report suppression function globally on the Switch.
0. Disable
1. Enable
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.4
tpMldRouterTime
Specify the aging time of the router port. Within this time,
if the switch don't receive MLD query message from the router port,
it will consider this port is not a router port any more,0,60-600 second.
Integer32r/w
Constraints:
range: 60-600
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.5
tpMldMemberTime
Specify the aging time of the member port. Within this time,
if the switch don't receive MLD report message from the member port,
it will consider this port is not a member port any more,0,60-600 second.
Integer32r/w
Constraints:
range: 60-600
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.6
tpMldLeaveTime
Specify the leave time for the VLAN.
When the switch receives a leave message from a port to leave a multicast group,
it will wait for a leave time before removing the port from the multicast group.
Integer32r/w
Constraints:
range: 1-30
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.7
tpMldRouterPort
Config the static router ports which are mainly used in the network with
stable topology.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.8
tpMldForbiddenRouterPort
Config the forbidden router ports which are mainly used to forbidden
specified ports to become router ports.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.9
tpMldQueryEnable
Select Enable/Disable MLD Querier.
0. Disable
1. Enable
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.10
tpMldQueryInterval
Enter the Query message interval time. The Querier will send General Query Message with this interval. The interval is ranging from 10 to 300 seconds.
Integer32r/w
Constraints:
range: 10-300
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.11
tpMldQueryMaxResponseTime
Enter the value of Maximum Response Time field of the Query message. The host is expected to response to an IGMP general query within this time. The time is ranging from 1 to 25 seconds.
Integer32r/w
Constraints:
range: 1-25
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.12
tpMldQueryGeneralSrcIp
Enter the General Query Message source IP address.
OctetStringr/w .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.13
tpMldQueryLastMemberCount
Enter the Last Listener Query numbers. When the multicast group has no more member ports,
it will send this numbers of Specific Query Message to check whether there is another member.
It is ranging from 1 to 5.
Integer32r/w
Constraints:
range: 1-5
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.14
tpMldQueryLastMemberInterval
Enter the Last Listener Query interval time. When the multicast group has no more member ports,
it will send the Specific Query Message with this interval time to check whether there is another
member. The interval is…
Integer32r/w
Constraints:
range: 1-5
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.15
tpMldVlanStatus
the following two values are states:
these values may be read or written
active(1),
notInService(2),

the following value is a state:
this value may be read, but not written
notReady(3),

the…
TPLINK-TC-MIBTPRowStatusr/w
Textual Convention: TPLINK-TC-MIBTPRowStatus Enumeration
Type Values:
1active
4createAndGo
6destroy
 .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.16

tpMldFilterPortTable

table
.1.3.6.1.4.1.11863.6.43.1.2.1.1 · 1 row entry · 4 columns
Open in standard view 
When the switch receives MLD report message, it examines 
the multicast filtering IP ID configured on the access port 
to determine if the port can join the multicast group. 
If the multicast IP is not filtered, the switch will add 
the port to the forward port list of the multicast group. 
Otherwise, the switch will drop the MLD report message. 
In that way, you can control the multicast groups that users 
can access.
tpMldFilterPortEntry entry .1.3.6.1.4.1.11863.6.43.1.2.1.1.1
An entry contains of the information of a port param.
Indexes
Column Syntax OID
tpMldFilterMaxGroup
Specify the maximum number of multicast groups to prevent some
ports taking up too much bandwidth.
Integer32r/w
Constraints:
range: 0-1000
 .1.3.6.1.4.1.11863.6.43.1.2.1.1.1.2
tpMldFilterMaxGroupAction
The policy should be taken when the number of multicast group
a port has joined reach the maximum.
0.Drop: drop the successive report packet, and this port can
not join any other multicast group.
1.Replace: when the p…
Enumerationr/w
Enumerated Values:
0drop
1replace
 .1.3.6.1.4.1.11863.6.43.1.2.1.1.1.3
tpMldFilterBindAddrId
Enter the profile ID the port will be bound to. Only one profile
can be bound to each port.
OctetStringr/w
Constraints:
range: 0-3
 .1.3.6.1.4.1.11863.6.43.1.2.1.1.1.4
tpMldFilterPortLag
Displays the LAG number which the port belongs to.
OctetString
Constraints:
range: 0-255
 .1.3.6.1.4.1.11863.6.43.1.2.1.1.1.5

tpMldPktStatTable

table
.1.3.6.1.4.1.11863.6.43.1.3.1.1 · 1 row entry · 5 columns
Open in standard view 
A list of  multicast statistic Table.
tpMldPktStatEntry entry .1.3.6.1.4.1.11863.6.43.1.3.1.1.1
An entry contains of multicast packet statistics over each port.
Indexes
Column Syntax OID
tpMldQueryPktStat
Displays the number of query packets the port received.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.43.1.3.1.1.1.2
tpMldReportV1PktStat
Displays the number of MLDv1 report packets the port received.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.43.1.3.1.1.1.3
tpMldReportV2PktStat
Displays the number of MLDv2 report packets the port received.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.43.1.3.1.1.1.4
tpMldDonePktStat
Displays the number of done packets the port received.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.43.1.3.1.1.1.6
tpMldErrorPktStat
Displays the number of error packets the port received.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.43.1.3.1.1.1.7

tpMldMulticastGroupTable

table
.1.3.6.1.4.1.11863.6.43.1.4.1.1 · 1 row entry · 4 columns
Open in standard view 
A list of  multicast groups Table.
tpMldMulticastGroupEntry entry .1.3.6.1.4.1.11863.6.43.1.4.1.1.1
An entry contains of multicast packet statistics over each port.
Indexes
tpMldMulticastIP tpMldVlanID
Column Syntax OID
tpMldMulticastIP
Displays the multicast IP address.
OctetString .1.3.6.1.4.1.11863.6.43.1.4.1.1.1.1
tpMldVlanID
Displays the VLAN ID.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.43.1.4.1.1.1.2
tpMldForwardPorts
Displays the forward ports of multicast group.
OctetString
Constraints:
range: 0-50
 .1.3.6.1.4.1.11863.6.43.1.4.1.1.1.3
tpMldGrouptype
Displays the type of multicast group.
Enumeration
Enumerated Values:
0static
1dynamic
 .1.3.6.1.4.1.11863.6.43.1.4.1.1.1.4

tpMldMulticastStaticGroupTable

table
.1.3.6.1.4.1.11863.6.43.1.5.1.1 · 1 row entry · 4 columns
Open in standard view 
A list of  multicast groups Table.
tpMldMulticastStaticGroupEntry entry .1.3.6.1.4.1.11863.6.43.1.5.1.1.1
An entry contains of multicast packet statistics over each port.
Indexes
tpMldStaticMulticastIP tpMldStaticVlanID
Column Syntax OID
tpMldStaticMulticastIP
The multicast IP address.
OctetStringr/w .1.3.6.1.4.1.11863.6.43.1.5.1.1.1.1
tpMldStaticVlanID
The VLAN ID.
Integer32r/w
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.11863.6.43.1.5.1.1.1.2
tpMldStaticForwardPorts
The forward ports of multicast group.
OctetStringr/w
Constraints:
range: 0-50
 .1.3.6.1.4.1.11863.6.43.1.5.1.1.1.3
tpMldStaticGroupStatus
The following values are states:
these values may be used as follow:

active(1),if the entry is being used.
notInService(2),destory the entry.
notReady(3),destory the entry.
createAndGo(4),not being used
c…
TPLINK-TC-MIBTPRowStatusr/w
Textual Convention: TPLINK-TC-MIBTPRowStatus Enumeration
Type Values:
1active
4createAndGo
6destroy
 .1.3.6.1.4.1.11863.6.43.1.5.1.1.1.4