tpMldQueryEnable
TPLINK-MLDSNOOPING-MIB ·
.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.10
Object
column
r/w
Enumeration
Select Enable/Disable MLD Querier. 0. Disable 1. Enable
Context
- MIB
- TPLINK-MLDSNOOPING-MIB
- OID
.1.3.6.1.4.1.11863.6.43.1.1.3.1.1.10- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- tpMldVlanEntry
- Table
- tpMldVlanTable
- Siblings
- 15
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | disable |
1 | enable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| tpMldVlanId Enter the VLAN ID to enable MLD Snooping for the desired VLAN,1-4094. | column | Integer32 | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.1 |
| tpMldQueryInterval Enter the Query message interval time. The Querier will send General Query Message with this interval. The interval is ranging from 10 to 300 seconds. | column | Integer32 | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.11 |
| tpMldQueryMaxResponseTime Enter the value of Maximum Response Time field of the Query message. The host is expected to response to an IGMP general query within this time. The time is ranging from 1 to 25 s… | column | Integer32 | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.12 |
| tpMldQueryGeneralSrcIp Enter the General Query Message source IP address. | column | OctetString | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.13 |
| tpMldQueryLastMemberCount Enter the Last Listener Query numbers. When the multicast group has no more member ports,
it will send this numbers of Specific Query Message to check whether there is another me… | column | Integer32 | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.14 |
| tpMldQueryLastMemberInterval Enter the Last Listener Query interval time. When the multicast group has no more member ports,
it will send the Specific Query Message with this interval time to check whether t… | column | Integer32 | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.15 |
| tpMldVlanStatus the following two values are states:
these values may be read or written
active(1),
notInService(2),
the following value is a state:
this value may be read, but not… | column | TPLINK-TC-MIBTPRowStatus | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.16 |
| tpMldVlanEnable Select Enable/Disable MLD Snooping for the desired vlan.
0. Disable
1. Enable | column | Enumeration | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.2 |
| tpMldVlanFastLeave Select Enable/Disable Fast Leave feature for the desired vlan.
If Fast Leave is enabled for a vlan, the Switch will immediately
remove this port from the multicast group upon re… | column | Enumeration | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.3 |
| tpMldVlanReportSuppression Select Enable/Disable MLD Snooping report suppression function globally on the Switch.
0. Disable
1. Enable | column | Enumeration | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.4 |
| tpMldRouterTime Specify the aging time of the router port. Within this time,
if the switch don't receive MLD query message from the router port,
it will consider this port is not a router port … | column | Integer32 | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.5 |
| tpMldMemberTime Specify the aging time of the member port. Within this time,
if the switch don't receive MLD report message from the member port,
it will consider this port is not a member port … | column | Integer32 | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.6 |
| tpMldLeaveTime Specify the leave time for the VLAN.
When the switch receives a leave message from a port to leave a multicast group,
it will wait for a leave time before removing the port from… | column | Integer32 | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.7 |
| tpMldRouterPort Config the static router ports which are mainly used in the network with
stable topology. | column | OctetString | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.8 |
| tpMldForbiddenRouterPort Config the forbidden router ports which are mainly used to forbidden
specified ports to become router ports. | column | OctetString | .1.3.6.1.4.1.11863.6.43.1.1.3.1.1.9 |